Supported hardware
Revision as of 22:28, 17 October 2013 by Matthias Heidbrink (talk | contribs) (→Logic analyzers: Updated status of Dangerous Prototypes Buspirate to supported.)
sigrok is intended as a flexible, cross-platform, and hardware-independent software suite, i.e., it supports various devices from many different vendors.
Here is a list of currently supported devices (various stages of completeness) and devices we plan to support in the near future.
The lists are sorted by category (supported, in progress, planned), and alphabetically within those categories.
Logic analyzers
| Device | Status | Comments |
|---|---|---|
 |
 supported |
The ARMFLY Mini-Logic is a USB-based, 8-channel logic analyzer with up to 24MHz sampling rate. |
supported |
The ASIX SIGMA is a USB-based, 16-channel logic analyzer with up to 200MHz sampling rate, and with 256Mbit on-board memory. | |
 |
supported |
The Braintechnology USB Interface V2.x is a Cypress FX2 eval board, which can be used as USB-based, 16-channel logic analyzer with up to 24MHz sampling rate. |
 |
supported |
The Braintechnology USB-LPS is a USB-based, 16-channel logic analyzer (and signal generator) with up to 24MHz sampling rate. |
 |
supported |
The ChronoVu LA8 is a USB-based, 8-channel logic analyzer with up to 100MHz sampling rate. |
 |
supported |
The CWAV USBee SX is a USB-based, 8-channel logic analyzer (and signal generator) with up to 24MHz sampling rate. |
 |
supported |
The Dangerous Prototypes Buspirate is a USB-based, 5-channel logic analyzer with up to 1MHz sampling rate. It uses the extended SUMP protocol. The Buspirate supports a logic analyzer mode and can thus be used for sample captures, however only at low speeds. |
 |
supported |
The EE Electronics ESLA100 is a USB-based, 8-channel logic analyzer with up to 24MHz sampling rate. |
 |
supported |
The IKALOGIC Scanalogic-2 is a USB-based, 4-channel logic analyzer with up to 20MHz sampling rate. |
 |
supported |
The IKALOGIC ScanaPLUS is a USB-based, 9-channel logic analyzer with up to 100MHz sampling rate. |
 |
supported |
The KingST KQS3506-LA16100 is a USB-based, 16-channel logic analyzer with 100/50/32/16MHz sampling rate (at 3/6/9/16 enabled channels). |
 |
supported |
The Lcsoft Mini Board is a Cypress FX2 eval board, which can be used as USB-based, 16-channel logic analyzer with up to 24MHz sampling rate. |
 |
supported |
The Logic Shrimp is a USB-based, 4-channel logic analyzer with up to 20MHz sampling rate. It uses the extended SUMP protocol. |
 |
supported |
The MCU123 Saleae Logic clone is a USB-based, 8-channel logic analyzer with up to 24MHz sampling rate. |
 |
supported |
The MCU123 USBee AX Pro clone is a USB-based, 8-channel logic analyzer with up to 24MHz sampling rate. |
 |
supported |
The Openbench Logic Sniffer (OLS) is a USB-based (and FPGA-based), 32-channel logic analyzer with up to 100MHz sampling rate and advanced trigger functionality. It is a fully open source device — the circuit design, VHDL code for the FPGA, firmware for the PIC microcontroller and Java-based client software are all freely available. It uses the extended SUMP protocol. |
 |
supported |
The Robomotic BugLogic 3 is a USB-based, 8-channel logic analyzer with up to 24MHz sampling rate. |
 |
supported |
The Robomotic MiniLogic is a USB-based, 8-channel logic analyzer with up to 24MHz sampling rate. |
 |
supported |
The Saleae Logic is a USB-based, 8-channel logic analyzer with up to 24MHz sampling rate. |
 |
supported |
The Saleae Logic16 is a USB-based, 16-channel logic analyzer with 100/50/32/16MHz sampling rate (at 3/6/9/16 enabled channels). |
 |
supported |
The WayEngineer Saleae16 is a USB-based, 16-channel logic analyzer with 100/50/32/16MHz sampling rate (at 3/6/9/16 enabled channels). |
 |
supported |
The ZEROPLUS Logic Cube LAP-C(16032) is a USB-based, 16-channel logic analyzer with up to 100MHz sampling rate. |
 |
supported |
The ZEROPLUS LAP-16128U is a USB-based, 16-channel logic analyzer with up to 200MHz sampling rate. |
 |
 in progress |
The ChronoVu LA16 is a USB-based, 16-channel logic analyzer with up to 200MHz sampling rate. |
 |
in progress |
The RockyLogic Ant8 is a USB-based, 8-channel logic analyzer with up to 500MHz sampling rate. |
 |
in progress |
The RockyLogic Ant18e is a USB-based, 18-channel logic analyzer with up to 1GHz sampling rate. |
 |
 planned |
The Acute PKLA-1216 is a USB-based, 16-channel logic analyzer with up to 200MHz sampling rate. |
 |
planned |
The Hantek 4032L is a USB-based, 32-channel, 400MHz logic analyzer with 2Gbit memory. |
 |
planned |
The Ideofy LA-08 is a USB-based, 8-channel logic analyzer with a max. samplerate of 96Msps@2ch (or 60msps@4ch, or 30msps@8ch). |
 |
planned |
The Intronix Logicport LA1034 is a USB-based (and FPGA-based), 34-channel logic analyzer with up to 500MHz sampling rate. |
 |
planned |
The Link Instruments LA-5580 is a USB-based, 80-channel logic analyzer with up to 500MHz samplerate. There's an optional pattern generator pod with 100 Mpoints/s. |
 |
planned |
The Microchip PICkit2 is a USB-based, 3-channel logic analyzer with up to 1MHz sampling rate. The PICkit2 is actually a programmer/debugger for PIC microcontrollers, but it can also be used as logic analyzer. |
 |
planned |
The MiniLA is a parallel port based, 32-channel logic analyzer with up to 100MHz sampling rate. |
 |
planned |
The MiniLA Mockup is a USB-based, 32-channel logic analyzer with up to 100MHz sampling rate. |
 |
planned |
The Sysclk LWLA1016 is a USB-based, 16-channel logic analyzer with up to 100MHz sampling rate. |
 |
planned |
The TechTools DigiView DV1-100 is a USB-based, 18-channel logic analyzer with 100MHz sampling rate. |
 |
planned |
The XMOS XTAG-2 is a USB based, ????-channel logic analyzer with up to 50MHz sampling rate. |
|
planned |
The ZEROPLUS Logic Cube LAP-C(322000) is a USB-based, 32-channel logic analyzer with a max. samplerate of 200MHz. |
 |
planned |
The ZLG LA1032 is a USB-based, 32-channel, 100MHz logic analyzer. |
Mixed-signal devices
Devices which can be used as both logic analyzer and oscilloscopes.
| Device | Status | Comments |
|---|---|---|
 |
supported |
The ARMFLY AX-Pro is a USB-based, 8-channel logic analyzer with up to 24MHz sampling rate, and with 2 additional analog channels.
Note: Only the logic analyzer functionality is supported so far, analog support is work in progress. |
 |
supported |
The EE Electronics ESLA201A is a USB-based, 8-channel logic analyzer with up to 24MHz sampling rate, and with 2 additional analog channels.
Note: Only the logic analyzer functionality is supported so far, analog support is work in progress. |
 |
supported |
The XZL_Studio AX is a USB-based, 8-channel logic analyzer with up to 24MHz sampling rate, with 2 additional analog channels and an independent trigger pin.
Note: Only the logic analyzer functionality is supported so far, analog support is work in progress, as is trigger. |
 |
in progress |
The BitScope BS10 is a mixed-signal oscilloscope, logic analyzer and spectrum analyzer. |
 |
in progress |
The Link Instruments MSO-19 is a USB-based, 1-channel 2GSa/s oscilloscope, 8-channel 200MSa/s logic analyzer, 100MSa/s pattern generator and a TDR. |
 |
planned |
The Agilent MSO7104A is a standalone, 4-channel mixed-signal digital storage oscilloscope (1GHz bandwidth, 4GSa/s samplerate, 16-channel logic analyzer). |
 |
planned |
The Digilent Analog Discovery is a USB-based 100MSa/s dual channel oscilloscope, function generator, logic analyzer and pattern generator. |
 |
planned |
The Hantek 1008C is a USB-based 8-channel oscilloscope, with 8 channel digital pattern generator |
 |
planned |
The Meilhaus MEphisto Scope1 is a USB-based multifunction acquisition device. |
 |
planned |
The PoLabs PoScope Basic2 is a USB-based, 16-channel logic analyzer (plus oscilloscope, signal/pattern generator, and more) with up to 8MHz sampling rate. |
planned |
The QuantAsylum QA100 is a USB-based, mixed-mode oscilloscope with 12 digital inputs, 2 analog, 1 trigger and 1 audio waveform generator. | |
 |
planned |
The Rigol VS5202D is a USB-based, 2-channel analog oscilloscope (400MSa/S, 200MHz bandwidth) and 16-channel logic analyzer (200MHz sampling rate). |
|
planned |
The XZL_Studio DX is a USB-based, 16-channel logic analyzer with up to 24MHz sampling rate, and with 2 additional analog channels. |
Oscilloscopes
| Device | Status | Comments |
|---|---|---|
 |
supported |
The Fluke ScopeMeter 199B is a handheld combined multimeter and oscilloscope. Only the multimeter functionality is supported; the device's slow communication speed does not allow for properly supporting it as an oscilloscope in sigrok. |
 |
supported |
The Hantek DSO-2090 is a USB-based, 2-channel oscilloscope with an analog bandwidth of 40MHz and 100MS/s sampling rate. |
 |
supported |
The Rigol DS1052E is a 50MHz, 1GSa/s, 2-channel digital storage oscilloscope. It can be upgraded to 100MHz analog bandwidth with a software modification. |
 |
supported |
The Rigol DS1102E is a 100MHz, 1GSa/s, 2-channel digital storage oscilloscope. |
 |
in progress |
The Focussz Fosc21 is a USB-serial based, 2-channel oscilloscope with an analog bandwidth of 3kHz and a sampling rate of 8kHz (1 channel) / 4kHz (2 channels). |
 |
in progress |
The Hantek DSO-5200A is a USB-based, 2-channel oscilloscope with an analog bandwidth of 200MHz and 250MS/s sampling rate. |
 |
in progress |
The Nexus-Computing OsciPrime is a USB-based, 2-channel oscilloscope with an analog bandwidth of 3.3MHz-8MHz. It is 100% open source hardware and software. |
 |
in progress |
The Velleman PCSU1000 is a USB-based, 2-channel oscilloscope with an analog bandwidth of 50MHz and 1GS/s sampling rate. |
 |
in progress |
The Hantek DSO-2250 is a USB-based, 2-channel oscilloscope with an analog bandwidth of 100MHz and 250MS/s sampling rate. |
|
planned |
The Hantek DSO-1200 is a USB-based, 2-channel oscilloscope with an analog bandwidth of 200MHz and 500MS/s sampling rate (and a multimeter). |
 |
planned |
The Fluke ScopeMeter 123 is a handheld, 2-channel oscilloscope with an analog bandwidth of 20MHz and 25MS/s sampling rate. |
 |
planned |
The Pico Technology PicoScope 2203 is a USB-based, 2-channel oscilloscope with an analog bandwidth of 5MHz and 40/20MS/s sampling rate (1-/2-channel one-shot mode). |
 |
planned |
The Pico Technology PicoScope 2205 is a USB-based, 2-channel oscilloscope with an analog bandwidth of 25MHz and 200/100MS/s sampling rate (1-/2-channel one-shot mode). |
 |
planned |
The Pico Technology PicoScope 3206 is a USB-based, 2-channel oscilloscope with an analog bandwidth of 200MHz and 200/100MS/s sampling rate (1-/2-channel one-shot mode). |
 |
planned |
The Pico Technology PicoScope 5203 is a USB-based, 2-channel oscilloscope with an analog bandwidth of 250MHz and 1/0,5GS/s sampling rate (1-/2-channel one-shot mode). |
 |
planned |
The Incite Technology USB-DUXfast is an USB-based analog data acquisition device. It supports up to 16 channels at 3MHz. |
 |
planned |
The Voltcraft DSO-220 is a USB-based, 2-channel oscilloscope with an analog bandwidth of 20MHz and 60MS/s sampling rate. |
 |
planned |
The Voltcraft DSO-3062C is a 60MHz, 1GSa/s, 2-channel digital storage oscilloscope. It can be upgraded to 200MHz analog bandwidth with a software modification. |
Multimeters
| Device | Status | Comments |
|---|---|---|
|
supported |
The Agilent U1231A is a 6000 counts, CAT III (600V) handheld digital multimeter with USB or Bluetooth connectivity. |
 |
supported |
The Agilent U1232A is a 6000 counts, CAT III (600V) handheld digital multimeter with USB or Bluetooth connectivity. |
|
supported |
The Agilent U1233A is a 6000 counts, CAT III (600V) handheld digital multimeter with USB or Bluetooth connectivity. |
 |
supported |
The Brymen BM857 is a 50000 counts (500000 DC), CAT III (1000V) / CAT IV (600V) handheld digital multimeter with RS232 connectivity. |
 |
supported |
The Digitek DT4000ZC is a 4000 counts, CAT II (600V) handheld digital multimeter with RS232 connectivity. |
 |
supported |
The Fluke 187/189 are 50000 counts, handheld digital multimeters with RS232 connectivity. |
 |
supported |
The Fluke 287/289 are 50000 counts handheld digital multimeters with RS232 connectivity. |
 |
supported |
The ISO-TECH IDM103N is a 4000 counts, handheld digital multimeter with RS232 connectivity. |
 |
supported |
The MASTECH MAS345 is a 4000 counts, CAT II handheld digital multimeter with RS232 connectivity. |
 |
supported |
The PCE PCE-DM32 is a 4000 counts, CAT III (1000V) / CAT IV (600V) handheld digital multimeter with RS232 connectivity. |
 |
supported |
The PeakTech 3410 is a 4000 counts, CAT II (1000V) handheld digital multimeter with RS232 connectivity. |
 |
supported |
The PeakTech 4370 is a 2000 counts, CAT II (1000V) handheld digital multimeter with RS232 connectivity. |
 |
supported |
The RadioShack 22-168 is a 2000 counts, handheld digital multimeter with RS232 connectivity. |
 |
supported |
The RadioShack 22-805 is a 4000 counts, CAT II (600V) handheld digital multimeter with RS232 connectivity. |
 |
supported |
The RadioShack 22-812 is a 4000 counts, CAT II (600V) handheld digital multimeter with RS232 connectivity. |
 |
supported |
The Tecpel DMM-8061 is a 4000 counts, CAT IV (600V) handheld digital multimeter with RS232 or USB connectivity. |
 |
supported |
The TekPower TP4000ZC is a 4000 counts, CAT II (600V) handheld digital multimeter with RS232 connectivity. |
 |
supported |
The UNI-T UT60E is a 4000 counts, CAT III (1000V) / CAT IV (600V) handheld digital multimeter with RS232 or USB connectivity. |
 |
supported |
The UNI-T UT61D is a 6000 counts, CAT II (600V) / CAT III (300V) handheld digital multimeter with RS232 or USB connectivity. |
 |
supported |
The UNI-T UT61E is a 22000 counts, CAT II (600V) / CAT III (300V) handheld digital multimeter with RS232 or USB connectivity. |
 |
supported |
The V&A VA18B is a 6000 counts, CAT II (1000V) handheld digital multimeter with USB connectivity. |
 |
supported |
The Victor 86C is a 4000 counts, CAT III (1000V) handheld digital multimeter with USB connectivity. |
 |
supported |
The Victor 70C is a 4000 counts, CAT II handheld digital multimeter with USB connectivity. |
 |
supported |
The Voltcraft M-3650D is a 2000 counts, handheld digital multimeter with RS232 connectivity. |
 |
supported |
The Voltcraft VC-820 is a 4000 counts, CAT III (1000V) / CAT IV (600V) handheld digital multimeter with RS232 or USB connectivity. |
 |
supported |
The Voltcraft VC-830 is a 6000 counts, CAT III (1000V) / CAT IV (600V) handheld digital multimeter with RS232 or USB connectivity. |
 |
supported |
The Voltcraft VC-840 is a 4000 counts, CAT IV (600V) handheld digital multimeter with RS232 or USB connectivity. |
 |
planned |
The APPA 107 is a 4000 / 20000 counts, handheld digital multimeter with RS232 connectivity. |
 |
planned |
The Digitek DT8000 is a 8000 counts, handheld digital multimeter with RS232 connectivity. |
 |
planned |
The Digitek DT80000 is a 80000 counts, handheld digital multimeter with RS232 connectivity. |
 |
planned |
The Escort 179 is a 10000 counts, handheld digital multimeter with RS232 connectivity. |
 |
planned |
The Gossen-Metrawatt METRAHIT 30M is a 200000 counts, CAT II (600V) / CAT III (300V) handheld digital multimeter with RS232 or USB connectivity. |
 |
planned |
The MASTECH M9803R is a 4000 counts, CAT II (1000V) digital bench multimeter with RS232 connectivity. |
 |
planned |
The Metex M-3650CR is a 2000 counts, handheld digital multimeter with RS232 connectivity. |
 |
planned |
The Metrix MX53 is a 50000 counts, handheld digital multimeter with RS232 connectivity. |
 |
planned |
The Metrix MX56C is a 50000 counts, handheld digital multimeter with RS232 connectivity. |
 |
planned |
The Norma DM9x0 are a series of 21000 counts, handheld digital multimeters with RS232 connectivity. |
|
planned |
The Protek 6500 is a 50000 counts handheld digital multimeter with RS232 connectivity. |
 |
planned |
The Voltcraft M-3890DT is a 4000 counts, CAT II handheld digital multimeter with USB connectivity. |
 |
planned |
The Voltcraft M-4650CR is a ???? counts, handheld digital multimeter with RS232 connectivity. |
 |
planned |
The Voltcraft M-4660A is a 20000 counts, handheld digital multimeter with RS232 connectivity. |
 |
planned |
The Voltcraft VC-920 is a 40000/4000 counts, handheld digital multimeter with RS232 or USB connectivity. |
 |
planned |
The Voltcraft VC-940 is a 40000/4000 counts, handheld digital multimeter with RS232 or USB connectivity. |
LCR meters
TODO.
Sound level meters
| Device | Status | Comments |
|---|---|---|
 |
supported |
The CEM DT-8852 is an IEC 61672-1 class 2-compliant sound level meter with USB connectivity. |
 |
supported |
The Colead SL-5868P is a sound level meter with RS232 connectivity. |
 |
supported |
The Kecheng KC-330B is a cheap sound level data logger with USB interface. |
 |
supported |
The Tondaj SL-814 is a sound level meter with USB connectivity. |
 |
in progress |
The Voltcraft DL-161S is a sound level meter with USB connectivity. |
 |
planned |
The PCE PCE-222 is a multi-function measurement device (light meter, thermometer, hygrometer, and sound level meter) with RS232 connectivity. |
 |
planned |
The Voltcraft DL-160S is a sound level meter with USB connectivity. |
Thermometers
| Device | Status | Comments |
|---|---|---|
 |
supported |
The Lascar Electronics EL-USB-2 is a USB-based temperature and humidity logger. |
 |
supported |
The MIC 98581 is a USB-based temperature logger. |
 |
supported |
The MIC 98583 is a USB-based temperature and humidity logger. |
 |
supported |
The UNI-T UT325 is a dual thermocouple logging thermometer. |
 |
supported |
The Voltcraft K204 is a 4-channel temperature logger with RS232 connectivity. |
 |
planned |
The Elitech RC-3 is a USB-based temperature logger. |
|
planned |
The PCE PCE-222 is a multi-function measurement device (light meter, thermometer, hygrometer, and sound level meter) with RS232 connectivity. |
 |
planned |
The RDing TEMPer is a USB-based temperature logger. |
 |
planned |
The RDing TEMPer Gold is a USB-based temperature logger. |
 |
planned |
The RDing TEMPer1 is a USB-based temperature logger. |
 |
planned |
The RDing TEMPer1K2 is a USB-based temperature logger. |
 |
planned |
The Voltcraft DL-120TH is a USB-based temperature logger. |
 |
planned |
The Voltcraft DL-140TH is a USB-based temperature logger. |
Hygrometers
| Device | Status | Comments |
|---|---|---|
|
supported |
The Lascar Electronics EL-USB-2 is a USB-based temperature and humidity logger. |
|
supported |
The MIC 98583 is a USB-based temperature and humidity logger. |
|
planned |
The PCE PCE-222 is a multi-function measurement device (light meter, thermometer, hygrometer, and sound level meter) with RS232 connectivity. |
 |
planned |
The SiLabs Si7005USB-Dongle is a USB-based temperature and humidity logger. |
Anemometers
| Device | Status | Comments |
|---|---|---|
 |
planned |
The MASTECH MS6252B an anemometer with USB connectivity. |
Light meters
| Device | Status | Comments |
|---|---|---|
 |
planned |
The Lutron YK-2005LX is a light meter with RS232 connectivity. |
|
planned |
The PCE PCE-222 is a multi-function measurement device (light meter, thermometer, hygrometer, and sound level meter) with RS232 connectivity. |
DAQs
| Device | Status | Comments |
|---|---|---|
 |
planned |
The NI USB-6008 is a USB-based DAQ with 8 analog inputs (12 bits, max. 10kS/s), 2 analog outputs (12 bits, 150Hz update rate), and 12 digital I/Os. |
Dataloggers
| Device | Status | Comments |
|---|---|---|
 |
supported |
The Lascar Electronics EL-USB-CO is a standalone carbon monoxide (CO) logger. |
 |
planned |
The GSG Indoor Air Monitor is a USB-based air quality monitor. |
 |
planned |
The MAUL studio i is an RS232-based weighing scale. |
 |
planned |
The Voltcraft CO-20 is a USB-based air quality monitor. |
Function generators
| Device | Status | Comments |
|---|---|---|
 |
planned |
The Hantek DDS-3X25 is a 25MHz PC-based function generator (requires a USB connection to work). |
 |
planned |
The Siglent SDG1010 is a 10MHz function generator with USB connectivity. |
RF Receivers
| Device | Status | Comments |
|---|---|---|
|
in progress |
The Per Vices Noctar is a PCIe IQ modulator/demodulator board. |
Spectrum analyzers
TODO.
Power supplies
| Device | Status | Comments |
|---|---|---|
 |
planned |
The Manson HCS-3202 is a 1-channel programmable power supply (1-36V/0-10A) with USB connectivity. |
GPIB interfaces
| Device | Status | Comments |
|---|---|---|
 |
planned |
The Beiming S82357 is a USB-based, hardware-implemented GPIB interface (a clone of the Agilent 82357B USB/GPIB interface). |
 |
planned |
The ICS 488-USB is a USB-based, hardware-implemented GPIB interface. |
 |
planned |
The GPIB-USB 82357B clone is a USB-based, hardware-implemented GPIB interface (a clone of the Agilent 82357B USB/GPIB interface). |
 |
planned |
The National Instruments GPIB-ENET is an Ethernet-based, hardware-implemented GPIB interface. |
 |
planned |
The National Instruments GPIB-USB-HS is a USB-based, hardware-implemented GPIB interface. |
 |
planned |
The Prologix GPIB-USB is a USB-based, firmware-implemented GPIB interface. |
Potential other candidates
If you own any other logic analyzers (or oscilloscopes, multimeters, dataloggers, etc.) and want to add support for them in sigrok (or donate/lend devices to developers), please let us know. We're always happy to add more hardware support! Contact Bert Vermeulen and Uwe Hermann if you want to help out.