Supported hardware

sigrok is intended as a flexible, cross-platform, and hardware-independent software suite, i.e., it supports various devices from many different vendors.

Here is a list of currently supported devices (various stages of completeness) and devices we plan to support in the near future.

The lists are sorted by category (supported, in progress, planned), and alphabetically within those categories.

Logic analyzers

Device	Status	Comments
	supported	The ARMFLY Mini-Logic is a USB-based, 8-channel logic analyzer with up to 24MHz sampling rate.
File:Sigma2 2.png	supported	The ASIX SIGMA is a USB-based, 16-channel logic analyzer with up to 200MHz sampling rate, and with 256Mbit on-board memory.
	supported	The Braintechnology USB Interface V2.x is a Cypress FX2 eval board, which can be used as USB-based, 16-channel logic analyzer with up to 24MHz sampling rate.
	supported	The Braintechnology USB-LPS is a USB-based, 16-channel logic analyzer (and signal generator) with up to 24MHz sampling rate.
	supported	The ChronoVu LA8 is a USB-based, 8-channel logic analyzer with up to 100MHz sampling rate.
	supported	The CWAV USBee SX is a USB-based, 8-channel logic analyzer (and signal generator) with up to 24MHz sampling rate.
	in progress	The Dangerous Prototypes Buspirate is a USB-based, 5-channel logic analyzer with up to 1MHz sampling rate. It uses the extended SUMP protocol. The Buspirate supports a logic analyzer mode and can thus be used for sample captures, however only at low speeds.
	supported	The EE Electronics ESLA100 is a USB-based, 8-channel logic analyzer with up to 24MHz sampling rate.
	supported	The Lcsoft Mini Board is a Cypress FX2 eval board, which can be used as USB-based, 16-channel logic analyzer with up to 24MHz sampling rate.
	supported	The Logic Shrimp is a USB-based, 4-channel logic analyzer with up to 20MHz sampling rate. It uses the extended SUMP protocol.
	supported	The Openbench Logic Sniffer (OLS) is a USB-based (and FPGA-based), 32-channel logic analyzer with up to 100MHz sampling rate and advanced trigger functionality. It is a fully open source device — the circuit design, VHDL code for the FPGA, firmware for the PIC microcontroller and Java-based client software are all freely available. It uses the extended SUMP protocol.
	supported	The Robomotic BugLogic 3 is a USB-based, 8-channel logic analyzer with up to 24MHz sampling rate.
	supported	The Robomotic MiniLogic is a USB-based, 8-channel logic analyzer with up to 24MHz sampling rate.
	supported	The Saleae Logic is a USB-based, 8-channel logic analyzer with up to 24MHz sampling rate.
	supported	The ZEROPLUS Logic Cube LAP-C(16032) is a USB-based, 16-channel logic analyzer with up to 100MHz sampling rate.
	in progress	The RockyLogic Ant8 is a USB-based, 8-channel logic analyzer with up to 500MHz sampling rate.
	in progress	The RockyLogic Ant18e is a USB-based, 18-channel logic analyzer with up to 1GHz sampling rate.
	planned	The Acute PKLA-1216 is a USB-based, 16-channel logic analyzer with up to 200MHz sampling rate.
	planned	The Ideofy LA-08 is a USB-based, 8-channel logic analyzer with a max. samplerate of 96Msps@2ch (or 60msps@4ch, or 30msps@8ch).
	planned	The Ikalogic SCANALOGIC-2 PRO is a USB-based, 4-channel logic analyzer with up to 20MHz sampling rate.
	planned	The Intronix Logicport LA1034 is a USB-based (and FPGA-based), 34-channel logic analyzer with up to 500MHz sampling rate.
	planned	The Microchip PICkit2 is a USB-based, 3-channel logic analyzer with up to 1MHz sampling rate. The PICkit2 is actually a programmer/debugger for PIC microcontrollers, but it can also be used as logic analyzer.
	planned	The MiniLA Mockup is a USB-based, 32-channel logic analyzer with up to 100MHz sampling rate.
	planned	The Saleae Logic16 is a USB-based, 16-channel logic analyzer with 100/50/25/12.5MHz sampling rate (at 2/4/8/16 enabled channels).
	planned	The Sysclk LWLA1016 is a USB-based, 16-channel logic analyzer with up to 100MHz sampling rate.
	planned	The TechTools DigiView DV1-100 is a USB-based, 18-channel logic analyzer with 100MHz sampling rate.
	planned	The ZEROPLUS LAP-16128U is a USB-based, 16-channel logic analyzer with up to 200MHz sampling rate.
	planned	The ZEROPLUS Logic Cube LAP-C(322000) is a USB-based, 32-channel logic analyzer with a max. samplerate of 200MHz.
	planned	The ZLG LA1032 is a USB-based, 32-channel, 100MHz logic analyzer.

Mixed-signal devices

Devices which can be used as both logic analyzer and oscilloscopes.

Device	Status	Comments
	supported	The ARMFLY AX-Pro is a USB-based, 8-channel logic analyzer with up to 24MHz sampling rate, and with 2 additional analog channels. Note: Only the logic analyzer functionality is supported so far, analog support is work in progress.
	supported	The EE Electronics ESLA201A is a USB-based, 8-channel logic analyzer with up to 24MHz sampling rate, and with 2 additional analog channels. Note: Only the logic analyzer functionality is supported so far, analog support is work in progress.
	supported	The XZL Studio DX is a USB-based, 16-channel logic analyzer with up to 24MHz sampling rate, and with 2 additional analog channels. Note: Only the logic analyzer functionality is supported so far, analog support is work in progress.
	in progress	The Link Instruments MSO-19 is a USB-based, 1-channel 2GSa/s oscilloscope, 8-channel 200MSa/s logic analyzer, 100MSa/s pattern generator and a TDR.
	planned	The Agilent MSO7104A is a standalone, 4-channel mixed-signal digital storage oscilloscope (1GHz bandwidth, 4GSa/s samplerate, 16-channel logic analyzer).
	planned	The Digilent Analog Discovery is a USB-based 100MSa/s dual channel oscilloscope, function generator, logic analyzer and pattern generator.
	planned	The Meilhaus MEphisto Scope1 is a USB-based multifunction acquisition device.
	planned	The PoLabs PoScope Basic2 is a USB-based, 16-channel logic analyzer (plus oscilloscope, signal/pattern generator, and more) with up to 8MHz sampling rate.
File:QA100.png	planned	The QuantAsylum QA100 is a USB-based, mixed-mode oscilloscope with 12 digital inputs, 2 analog, 1 trigger and 1 audio waveform generator.
File:Rigol VS5202D Full.jpg	planned	The Rigol VS5202D is a USB-based, 2-channel analog oscilloscope (400MSa/S, 200MHz bandwidth) and 16-channel logic analyzer (200MHz sampling rate).

Oscilloscopes

Device	Status	Comments
	supported	The Fluke ScopeMeter 199B is a handheld combined multimeter and oscilloscope. Only the multimeter functionality is supported; the device's slow communication speed does not allow for properly supporting it as an oscilloscope in sigrok.
	supported	The Hantek DSO-2090 is a USB-based, 2-channel oscilloscope with an analog bandwidth of 40MHz and 100MS/s sampling rate.
	in progress	The Hantek DSO-5200A is a USB-based, 2-channel oscilloscope with an analog bandwidth of 200MHz and 250MS/s sampling rate.
	in progress	The Velleman PCSU1000 is a USB-based, 2-channel oscilloscope with an analog bandwidth of 50MHz and 1GS/s sampling rate.
	planned	The Hantek DSO-1200 is a USB-based, 2-channel oscilloscope with an analog bandwidth of 200MHz and 500MS/s sampling rate (and a multimeter).
	planned	The Fluke ScopeMeter 123 is a handheld, 2-channel oscilloscope with an analog bandwidth of 20MHz and 25MS/s sampling rate.
	planned	The Focussz Fosc21 is a USB-based, 2-channel oscilloscope with an analog bandwidth of 3kHz and a sampling rate of 8kHz (1 channel) / 4kHz (2 channels).
	planned	The Nexus-Computing OsciPrime is a USB-based, 2-channel oscilloscope with an analog bandwidth of 3.3MHz-8MHz. It is 100% open source hardware and software.
	planned	The Pico Technology PicoScope 2203 is a USB-based, 2-channel oscilloscope with an analog bandwidth of 5MHz and 40/20MS/s sampling rate (1-/2-channel one-shot mode).
	planned	The Pico Technology PicoScope 2205 is a USB-based, 2-channel oscilloscope with an analog bandwidth of 25MHz and 200/100MS/s sampling rate (1-/2-channel one-shot mode).
	planned	The Pico Technology PicoScope 3206 is a USB-based, 2-channel oscilloscope with an analog bandwidth of 200MHz and 200/100MS/s sampling rate (1-/2-channel one-shot mode).
	planned	The Pico Technology PicoScope 5203 is a USB-based, 2-channel oscilloscope with an analog bandwidth of 250MHz and 1/0,5GS/s sampling rate (1-/2-channel one-shot mode).
	planned	The Rigol DS1052E is a 50MHz, 1GSa/s, 2-channel digital storage oscilloscope. It can be upgraded to 100MHz analog bandwidth with a software modification.
	planned	The USB-DUXfast is an USB-based analog data acquisition device. It supports up to 16 channels at 3 MHz.
	planned	The Voltcraft DSO-3062C is a 60MHz, 1GSa/s, 2-channel digital storage oscilloscope. It can be upgraded to 200MHz analog bandwidth with a software modification.

Multimeters

Device	Status	Comments
	supported	The Agilent U1231A is a 6000 counts, CAT III (600V) handheld digital multimeter with USB or Bluetooth connectivity.
	supported	The Agilent U1232A is a 6000 counts, CAT III (600V) handheld digital multimeter with USB or Bluetooth connectivity.
	supported	The Agilent U1233A is a 6000 counts, CAT III (600V) handheld digital multimeter with USB or Bluetooth connectivity.
	in progress	The Brymen BM857 is a 50000 counts (500000 DC), CAT III (1000V) / CAT IV (600V) handheld digital multimeter with RS232 connectivity.
	supported	The Digitek DT4000ZC is a 4000 counts, CAT II (600V) handheld digital multimeter with RS232 connectivity.
	supported	The Fluke 187/189 are 50000 counts, handheld digital multimeters with RS232 connectivity.
	supported	The Fluke 287/289 are 50000 counts handheld digital multimeters with RS232 connectivity.
	supported	The MASTECH MAS345 is a 4000 counts, CAT II handheld digital multimeter with RS232 connectivity.
	supported	The PCE PCE-DM32 is a 4000 counts, CAT III (1000V) / CAT IV (600V) handheld digital multimeter with RS232 connectivity.
	supported	The PeakTech 3410 is a 4000 counts, CAT II (1000V) handheld digital multimeter with RS232 connectivity.
	supported	The PeakTech 4370 is a 2000 counts, CAT II (1000V) handheld digital multimeter with RS232 connectivity.
	supported	The RadioShack 22-168 is a 2000 counts, handheld digital multimeter with RS232 connectivity.
	supported	The RadioShack 22-812 is a 4000 counts, CAT II (600V) handheld digital multimeter with RS232 connectivity.
	supported	The TekPower TP4000ZC is a 4000 counts, CAT II (600V) handheld digital multimeter with RS232 connectivity.
	supported	The UNI-T UT61D is a 6000 counts, CAT II (600V) / CAT III (300V) handheld digital multimeter with RS232 or USB connectivity.
	supported	The V&A VA18B is a 6000 counts, CAT II (1000V) handheld digital multimeter with USB connectivity.
	supported	The Victor 86C is a 4000 counts, CAT III (1000V) handheld digital multimeter with USB connectivity.
	supported	The Victor 70C is a 4000 counts, CAT II handheld digital multimeter with USB connectivity.
	supported	The Voltcraft VC-820 is a 4000 counts, CAT III (1000V) / CAT IV (600V) handheld digital multimeter with RS232 or USB connectivity.
	in progress	The UNI-T UT61E is a 22000 counts, CAT II (600V) / CAT III (300V) handheld digital multimeter with RS232 or USB connectivity.
	in progress	The Voltcraft VC-840 is a 4000 counts, CAT IV (600V) handheld digital multimeter with RS232 or USB connectivity.
	planned	The Escort 179 is a 10000 counts, handheld digital multimeter with RS232 connectivity.
	planned	The MASTECH M9803R is a 4000 counts, CAT II (1000V) digital bench multimeter with RS232 connectivity.
	planned	The Protek 6500 is a 50000 counts handheld digital multimeter with RS232 connectivity.
	planned	The Voltcraft M-4660A is a 20000 counts, handheld digital multimeter with RS232 connectivity.

LCR meters

TODO.

Sound level meters

Device	Status	Comments
	supported	The Colead SL-5868P is a sound level meter with RS232 connectivity.
	supported	The Tondaj SL-814 is a sound level meter with USB connectivity.
	planned	The CEM DT-8852 is an IEC 61672-1 class 2-compliant sound level meter with USB connectivity.
	planned	The PCE PCE-222 is a multi-function measurement device (light meter, thermometer, hygrometer, and sound level meter) with RS232 connectivity.
	planned	The Voltcraft DL-160S is a sound level meter with USB connectivity.

Thermometers

Device	Status	Comments
	supported	The Lascar Electronics EL-USB-2 is a USB-based temperature and humidity logger.
	planned	The PCE PCE-222 is a multi-function measurement device (light meter, thermometer, hygrometer, and sound level meter) with RS232 connectivity.
	planned	The RDing TEMPer is a USB-based temperature logger.
	planned	The RDing TEMPer Gold is a USB-based temperature logger.
	planned	The RDing TEMPer1 is a USB-based temperature logger.
	planned	The RDing TEMPer1K2 is a USB-based temperature logger.
	planned	The Voltcraft DL-120TH is a USB-based temperature logger.
	planned	The Voltcraft DL-140TH is a USB-based temperature logger.
	planned	The UNI-T UT325 is a dual thermocouple logging thermometer.

Hygrometers

Device	Status	Comments
	planned	The PCE PCE-222 is a multi-function measurement device (light meter, thermometer, hygrometer, and sound level meter) with RS232 connectivity.

Anemometers

Device	Status	Comments
	planned	The MASTECH MS6252B an anemometer with USB connectivity.

Light meters

Device	Status	Comments
	planned	The Lutron YK-2005LX is a light meter with RS232 connectivity.
	planned	The PCE PCE-222 is a multi-function measurement device (light meter, thermometer, hygrometer, and sound level meter) with RS232 connectivity.

Dataloggers

Device	Status	Comments
	supported	The Lascar Electronics EL-USB-CO is a standalone carbon monoxide (CO) logger.
	planned	The GSG Indoor Air Monitor is a USB-based air quality monitor.
	planned	The MAUL studio i is an RS232-based weighing scale.
	planned	The Voltcraft CO-20 is a USB-based air quality monitor.

Function generators

Device	Status	Comments
	planned	The Hantek DDS-3X25 is a 25MHz PC-based function generator (requires a USB connection to work).
	planned	The Siglent SDG1010 is a 10MHz function generator with USB connectivity.

Power supplies

TODO

GPIB interfaces

Device	Status	Comments
	planned	The Beiming S82357 is a USB-based, hardware-implemented GPIB interface (a clone of the Agilent 82357B USB/GPIB interface).
	planned	The ICS 488-USB is a USB-based, hardware-implemented GPIB interface.
	planned	The GPIB-USB 82357B clone is a USB-based, hardware-implemented GPIB interface (a clone of the Agilent 82357B USB/GPIB interface).
	planned	The National Instruments GPIB-ENET is an Ethernet-based, hardware-implemented GPIB interface.
	planned	The National Instruments GPIB-USB-HS is a USB-based, hardware-implemented GPIB interface.
	planned	The Prologix GPIB-USB is a USB-based, firmware-implemented GPIB interface.

Potential other candidates

If you own any other logic analyzers (or oscilloscopes, multimeters, dataloggers, etc.) and want to add support for them in sigrok (or donate/lend devices to developers), please let us know. We're always happy to add more hardware support! Contact Bert Vermeulen and Uwe Hermann if you want to help out.