Supported hardware
Jump to navigation
Jump to search
sigrok is intended as a flexible, cross-platform, and hardware-independent software suite, i.e., it supports various devices from many different vendors.
Here is a list of currently supported devices (various stages of completeness) and devices we plan to support in the near future.
The lists are sorted by category (supported, in progress, planned), and alphabetically within those categories.
Logic analyzers
| Device | Status | Comments |
|---|---|---|
 |
 supported |
The ARMFLY Mini-Logic is a USB-based, 8-channel logic analyzer with up to 24MHz sampling rate. |
supported |
The ASIX SIGMA/SIGMA2 is a USB-based, 16-channel logic analyzer with up to 200MHz sampling rate, and with 256Mbit on-board memory. | |
 |
supported |
The Braintechnology USB Interface V2.x is a Cypress FX2 eval board, which can be used as USB-based, 16-channel logic analyzer with up to 24MHz sampling rate. |
 |
supported |
The Braintechnology USB-LPS is a USB-based, 16-channel logic analyzer (and signal generator) with up to 24MHz sampling rate. |
 |
supported |
The ChronoVu LA8 is a USB-based, 8-channel logic analyzer with up to 100MHz sampling rate. |
 |
supported |
The CWAV USBee SX is a USB-based, 8-channel logic analyzer (and signal generator) with up to 24MHz sampling rate. |
 |
supported |
The EE Electronics ESLA100 is a USB-based, 8-channel logic analyzer with up to 24MHz sampling rate. |
 |
supported |
The Lcsoft Mini Board is a Cypress FX2 eval board, which can be used as USB-based, 16-channel logic analyzer with up to 24MHz sampling rate. |
 |
supported |
The Logic Shrimp is a USB-based, 4-channel logic analyzer with up to 20MHz sampling rate. It uses the extended SUMP protocol. |
 |
supported |
The Openbench Logic Sniffer (OLS) is a USB-based (and FPGA-based), 32-channel logic analyzer with up to 100MHz sampling rate and advanced trigger functionality. It is a fully open source device — the circuit design, VHDL code for the FPGA, firmware for the PIC microcontroller and Java-based client software are all freely available. It uses the extended SUMP protocol. |
 |
supported |
The Robomotic BugLogic 3 is a USB-based, 8-channel logic analyzer with up to 24MHz sampling rate. |
 |
supported |
The Robomotic MiniLogic is a USB-based, 8-channel logic analyzer with up to 24MHz sampling rate. |
 |
supported |
The Saleae Logic is a USB-based, 8-channel logic analyzer with up to 24MHz sampling rate. |
 |
supported |
The ZEROPLUS Logic Cube LAP-C (16032) is a USB-based, 16-channel logic analyzer with up to 100MHz sampling rate. |
 in progress |
The Buspirate v3 is a USB-based, 5-channel logic analyzer with up to 1MHz sampling rate. It uses the extended SUMP protocol. The Buspirate supports a logic analyzer mode and can thus be used for sample captures, however only at low speeds. | |
 |
in progress |
The RockyLogic Ant18e is a USB-based, 18-channel logic analyzer with up to 1GHz sampling rate. |
 |
in progress |
The RockyLogic Ant8 is a USB-based, 8-channel logic analyzer with up to 500MHz sampling rate. |
 |
 planned |
The Acute PKLA-1216 is a USB-based, 16-channel logic analyzer with up to 200MHz sampling rate. |
planned |
The Ideofy LA-08 is a USB-based, 8-channel logic analyzer with a max. samplerate of 96Msps@2ch (or 60msps@4ch, or 30msps@8ch). | |
 |
planned |
The Ikalogic SCANALOGIC-2 PRO is a USB-based, 4-channel logic analyzer with up to 20MHz sampling rate. |
 |
planned |
The Intronix Logicport LA1034 is a USB-based (and FPGA-based), 34-channel logic analyzer with up to 500MHz sampling rate. |
 |
planned |
The Microchip PICkit2 is a USB-based, 3-channel logic analyzer with up to 1MHz sampling rate. The PICkit2 is actually a programmer/debugger for PIC microcontrollers, but it can also be used as logic analyzer. |
 |
planned |
The MiniLA Mockup is a USB-based, 32-channel logic analyzer with up to 100MHz sampling rate. |
 |
planned |
The Saleae Logic16 is a USB-based, 16-channel logic analyzer with 100/50/25/12.5MHz sampling rate (at 2/4/8/16 enabled channels). |
planned |
The ZLG LA1032 is a USB-based, 32-channel, 100MHz logic analyzer. |
Mixed-signal devices
Devices which can be used as both logic analyzer and oscilloscopes.
| Device | Status | Comments |
|---|---|---|
 |
supported |
The ARMFLY AX-Pro is a USB-based, 8-channel logic analyzer with up to 24MHz sampling rate, and with 2 additional analog channels.
Note: Only the logic analyzer functionality is supported so far, analog support is work in progress. |
 |
supported |
The EE Electronics ESLA201A is a USB-based, 8-channel logic analyzer with up to 24MHz sampling rate, and with 2 additional analog channels.
Note: Only the logic analyzer functionality is supported so far, analog support is work in progress. |
 |
in progress |
The Link Instruments MSO-19 is a USB-based, 1-channel 2GSa/s oscilloscope, 8-channel 200MSa/s logic analyzer, 100MSa/s pattern generator and a TDR. |
 |
planned |
The Agilent MSO7104A is a standalone, 4-channel mixed-signal digital storage oscilloscope (1GHz bandwidth, 4GSa/s samplerate, 16-channel logic analyzer). |
 |
planned |
The PoLabs PoScope Basic2 is a USB-based, 16-channel logic analyzer (plus oscilloscope, signal/pattern generator, and more) with up to 8MHz sampling rate. |
planned |
The QuantAsylum QA100 is a USB-based, mixed-mode oscilloscope with 12 digital inputs, 2 analog, 1 trigger and 1 audio waveform generator. | |
planned |
The Rigol VS5202D is a USB-based, 2-channel analog oscilloscope (400MSa/S, 200MHz bandwidth) and 16-channel logic analyzer (200MHz sampling rate). |
Oscilloscopes
| Device | Status | Comments |
|---|---|---|
 |
supported |
The Hantek DSO-2090 is a USB-based, 2-channel oscilloscope with an analog bandwidth of 40MHz and 100MS/s sampling rate. |
 |
in progress |
The Hantek DSO-5200A is a USB-based, 2-channel oscilloscope with an analog bandwidth of 200MHz and 250MS/s sampling rate. |
 |
planned |
The Pico Technology PicoScope 2203 is a USB-based, 2-channel oscilloscope with an analog bandwidth of 5MHz and 40/20MS/s sampling rate (1-/2-channel one-shot mode). |
 |
planned |
The Pico Technology PicoScope 2205 is a USB-based, 2-channel oscilloscope with an analog bandwidth of 25MHz and 200/100MS/s sampling rate (1-/2-channel one-shot mode). |
 |
planned |
The Pico Technology PicoScope 3206 is a USB-based, 2-channel oscilloscope with an analog bandwidth of 200MHz and 200/100MS/s sampling rate (1-/2-channel one-shot mode). |
 |
planned |
The Velleman PCSU1000 is a USB-based, 2-channel oscilloscope with an analog bandwidth of 50MHz and 1GS/s sampling rate. |
Multimeters
| Device | Status | Comments |
|---|---|---|
 |
supported |
The Agilent U123xA series are 6000 counts handheld digital multimeters with IR connectivity. |
 |
supported |
The Fluke 187/189 are 50000 counts, handheld digital multimeters with RS232 connectivity. |
 |
supported |
The Fluke 287/289 are 50000 counts handheld digital multimeters with RS232 connectivity. |
 |
supported |
The RadioShack 22-812 is a 4000 counts handheld digital multimeter with RS232 connectivity. |
 |
supported |
The TekPower TP4000ZC is a 4000 counts, CAT II (600V) handheld digital multimeter with RS232 connectivity. |
 |
supported |
The UNI-T UT61D is a 6000 counts, CAT II (600V) / CAT III (300V) handheld digital multimeter with RS232 or USB connectivity. |
 |
supported |
The Victor 86C is a 4000 counts, CAT III (1000V) handheld digital multimeter with USB connectivity. |
 |
supported |
The Victor 70C is a 4000 counts, CAT II handheld digital multimeter with USB connectivity. |
 |
in progress |
The V&A VA18B is a 6000 counts, CAT II (1000V) handheld digital multimeter with USB connectivity. |
 |
planned |
The Digitek DT4000ZC is a 4000 counts, CAT II (600V), handheld digital multimeter with RS232 connectivity. |
 |
planned |
The Escort 179 is a 10000 counts, handheld digital multimeter with RS232 connectivity. |
 |
planned |
The MASTECH MAS345 is a 4000 counts, CAT II handheld digital multimeter with RS232 connectivity. |
 |
planned |
The MASTECH M9803R is a 4000 counts, CAT II (1000V) digital bench multimeter with RS232 connectivity. |
 |
planned |
The Peaktech 4370 is a 2000 counts, CAT II (1000V) handheld digital multimeter with RS232 connectivity. |
 |
planned |
The Protek 6500 is a 50000 counts handheld digital multimeter with RS232 connectivity. |
 |
planned |
The UNI-T UT61E is a 22000 counts, CAT II (600V) / CAT III (300V) handheld digital multimeter with RS232 or USB connectivity. |
 |
planned |
The Voltcraft M-4660A is a 20000 counts, handheld digital multimeter with RS232 connectivity. |
 |
planned |
The Voltcraft VC-820 is a 4000 counts, CAT III (1000V) / CAT IV (600V) handheld digital multimeter with RS232 or USB connectivity. |
 |
planned |
The Voltcraft VC-840 is a 4000 counts, CAT IV (600V) handheld digital multimeter with RS232 or USB connectivity. |
Sound Level Meters
| Device | Status | Comments |
|---|---|---|
 |
in progress |
The Colead SL-5868P is a sound level meter with serial connectivity. |
 |
in progress |
The Tondaj SL-814 is a sound level meter with USB connectivity. |
Dataloggers
| Device | Status | Comments |
|---|---|---|
 |
planned |
The RDing TEMPer is a USB-based temperature logger. |
 |
planned |
The RDing TEMPer1 is a USB-based temperature logger. |
 |
planned |
The RDing TEMPer Gold is a USB-based temperature logger. |
 |
planned |
The UNI-T UT325 is a dual thermocouple logging thermometer. |
Function generators
| Device | Status | Comments |
|---|---|---|
 |
planned |
The Hantek DDS-3X25 is a 25MHz PC-based function generator (requires a USB connection to work). |
 |
planned |
The Siglent SDG1010 is a 10MHz function generator with USB connectivity. |
Power supplies
TODO
GPIB interfaces
| Device | Status | Comments |
|---|---|---|
 |
planned |
The Beiming S82357 is a USB-based, hardware-implemented GPIB interface (a clone of the Agilent 82357B USB/GPIB interface). |
 |
planned |
The ICS 488-USB is a USB-based, hardware-implemented GPIB interface. |
 |
planned |
The GPIB-USB 82357B clone is a USB-based, hardware-implemented GPIB interface (a clone of the Agilent 82357B USB/GPIB interface). |
 |
planned |
The National Instruments GPIB-ENET is an Ethernet-based, hardware-implemented GPIB interface. |
 |
planned |
The National Instruments GPIB-USB-HS is a USB-based, hardware-implemented GPIB interface. |
 |
planned |
The Prologix GPIB-USB a USB-based, firmware-implemented GPIB interface. |
Potential other candidates
If you own any other logic analyzers (or oscilloscopes, multimeters, dataloggers, etc.) and want to add support for them in sigrok (or donate/lend devices to developers), please let us know. We're always happy to add more hardware support! Contact Bert Vermeulen and Uwe Hermann if you want to help out.