Difference between revisions of "Lcsoft Mini Board"
Uwe Hermann (talk | contribs) m |
Uwe Hermann (talk | contribs) |
||
| Line 21: | Line 21: | ||
In sigrok, we use the open-source [[fx2lafw]] firmware for this logic analyzer. | In sigrok, we use the open-source [[fx2lafw]] firmware for this logic analyzer. | ||
See [[Lcsoft Mini Board/Info]] for some more details (such as '''lsusb - | See [[Lcsoft Mini Board/Info]] for some more details (such as '''lsusb -v''' output) on the device. | ||
== Hardware == | == Hardware == | ||
| Line 51: | Line 51: | ||
This version doesn't have the "Lcsoft" silkscreen (for unknown reasons). The EEPROM was desoldered manually by the owner. | This version doesn't have the "Lcsoft" silkscreen (for unknown reasons). The EEPROM was desoldered manually by the owner. | ||
'''Yet another version''': | |||
<gallery> | |||
File:Lcsoft cy7c68013a pcb top.jpg|<small>PCB, top</small> | |||
File:Lcsoft cy7c68013a pcb bottom.jpg|<small>PCB, bottom</small> | |||
</gallery> | |||
== Protocol == | == Protocol == | ||
| Line 56: | Line 63: | ||
Since we use the open-source [[fx2lafw]] firmware for this device, we don't need to know the protocol. | Since we use the open-source [[fx2lafw]] firmware for this device, we don't need to know the protocol. | ||
== Possible | == Possible issues == | ||
* With some kernel versions, and if the onboard EEPROM is disconnected (the jumper not connected) the kernel will automatically claim the device with a '''usbtest''' kernel module, seen in dmesg like '''usbtest 2-2:1.0: FX2 device''' — if this happens, sigrok will be unable to claim the device. Remove the '''usbtest''' kernel module as root to be able to use it: | * With some kernel versions, and if the onboard EEPROM is disconnected (the jumper not connected) the kernel will automatically claim the device with a '''usbtest''' kernel module, seen in dmesg like '''usbtest 2-2:1.0: FX2 device''' — if this happens, sigrok will be unable to claim the device. Remove the '''usbtest''' kernel module as root to be able to use it: | ||
| Line 66: | Line 73: | ||
$ '''sudo sh -c "echo 'blacklist usbtest' >> /etc/modprobe.d/blacklist.conf"''' | $ '''sudo sh -c "echo 'blacklist usbtest' >> /etc/modprobe.d/blacklist.conf"''' | ||
== Required | == Required testing hardware extensions == | ||
'''Do not directly hook the board pins to another circuit, if you don't know what you are doing! This could damage the board!''' | '''Do not directly hook the board pins to another circuit, if you don't know what you are doing! This could damage the board!''' | ||
Revision as of 23:20, 7 December 2014
 | |
| Status | supported |
|---|---|
| Source code | fx2lafw |
| Channels | 8/16 |
| Samplerate | 24MHz |
| Samplerate (state) | — |
| Triggers | none (SW-only) |
| Min/max voltage | -0.5V — 5.25V |
| Threshold voltage | Fixed: VIH=2.0V—5.25V, VIL=-0.5V—0.8V |
| Memory | none |
| Compression | none |
| Website | lctech-inc.com |
The Lcsoft CY7C68013A Mini Board is a Cypress FX2(LP) eval board, which can be used as USB-based, 16-channel logic analyzer with up to 24MHz sampling rate.
It is a clone of the Saleae Logic.
In sigrok, we use the open-source fx2lafw firmware for this logic analyzer.
See Lcsoft Mini Board/Info for some more details (such as lsusb -v output) on the device.
Hardware
- Main chip: Cypress CY7C68013A-56PVXC (FX2LP)
- 3.3V voltage regulator: Advanced Monolithic Systems ASM1117-3.3
- 16kB I2C EEPROM: Atmel AT24C128A
- 24MHz crystal: JY24.0000601
All the pins on the FX2(LP) are broken out to 40 header pins. There's an on/off toggle switch, a reset button, and a jumper that lets you select whether the FX2LP gets its configuration from a small EEPROM, or boots into the default mode. The EEPROM's default settings make it come up with the same VID:PID as a Saleae Logic.
Photos
PCB, front
PCB, back
A.M.S. AMS1117
Atmel AT24C128A
24MHz crystal
Cypress FX2LP
Slightly different version without "Lcsoft" silkscreen:
PCB, top
PCB, bottom
This version doesn't have the "Lcsoft" silkscreen (for unknown reasons). The EEPROM was desoldered manually by the owner.
Yet another version:
PCB, top
PCB, bottom
Protocol
Since we use the open-source fx2lafw firmware for this device, we don't need to know the protocol.
Possible issues
- With some kernel versions, and if the onboard EEPROM is disconnected (the jumper not connected) the kernel will automatically claim the device with a usbtest kernel module, seen in dmesg like usbtest 2-2:1.0: FX2 device — if this happens, sigrok will be unable to claim the device. Remove the usbtest kernel module as root to be able to use it:
$ sudo rmmod usbtest
You can add the usbtest module to a module blacklist permanently, at least in Debian-based distributions found in /etc/modprobe.d/blacklist.conf:
$ sudo sh -c "echo 'blacklist usbtest' >> /etc/modprobe.d/blacklist.conf"
Required testing hardware extensions
Do not directly hook the board pins to another circuit, if you don't know what you are doing! This could damage the board!
The simplest circuit would be adding at least resistors in between your circuit-in-test and the Lcsoft board, but be aware here that the Cypress FX2(LP) chip can only tolerate a maximum of 5V I/O. Better would be to use a clamp circuit like shown at Spiralbrain's Blog (but you do not need to add another EEPROM for sigrok with fx2lafw!). A buffer circuit using a 74HC241 IC for protection is also possible. Check the fx2lafw page to see which protection circuits are used on other logic analyzer boards.
More information can be found in Circuits for barebone boards.