Difference between revisions of "Noname XL-LOGIC16-100M"
| Line 18: | Line 18: | ||
The existing Saleae Logic16 support detects this device as an original, but fails to initialize the FPGA for capture. | The existing Saleae Logic16 support detects this device as an original, but fails to initialize the FPGA for capture. | ||
See [[XL-LOGIC16-100M/Info]] for more details (such as '''lsusb -v''' output) about the device. | See [[XL-LOGIC16-100M/Info]] for more details (such as '''lsusb -v''' output) about the device. (if ever desired) | ||
== Hardware == | == Hardware == | ||
A single phillips head screw holds the case together. The parts selection seem to be almost identical to the [[WayEngineer_Saleae16]] but that page doesn't have any internal photos for full comparison. | |||
Most notable are the complete lack of test points or programming headers! There are some unpopulated resistor/capacitor pairs on the backside, | |||
* '''FPGA''': [http://www.xilinx.com/support/index.html/content/xilinx/en/supportNav/silicon_devices/fpga/spartan-3a.html Xilinx Spartan-3A XC3S200A], 200K gates ([http://www.xilinx.com/support/documentation/data_sheets/ds529.pdf datasheeet]) | |||
* '''USB interface chip''': [http://www.cypress.com/?mpn=CY7C68013A-56PVXC Cypress CY7C68013A-56PVXC (FX2LP)] ([http://www.cypress.com/?docID=34060 datasheet]) | |||
* '''I2C EEPROM''': 2Kbit [http://www.atmel.com/devices/AT24C02B.aspx Atmel 24C02B] (markings: "ATMEL317 24C02BN SU27 D") ([http://www.atmel.com/Images/doc5126.pdf datasheet]) | |||
* '''3.3V voltage regulator''': [http://www.advanced-monolithic.com/products/voltreg.html#1117 Advanced Monolithic Systems AMS1117-3.3] ([http://ams-semitech.com/attachments/File/AMS1117_20120314.pdf datasheet], [http://www.advanced-monolithic.com/pdf/ds1117.pdf older datasheet]) | |||
* '''1.2V voltage regulator''': [http://www.advanced-monolithic.com/products/voltreg.html#1117 Advanced Monolithic Systems AMS1117-1.2] ([http://ams-semitech.com/attachments/File/AMS1117_20120314.pdf datasheet], [http://www.advanced-monolithic.com/pdf/ds1117.pdf older datasheet]) | |||
* '''Crystal:''' 24.000 | |||
Three LEDs, USB (green) COM (blue) and RUN (red) are on the board. | |||
== Photos == | == Photos == | ||
Revision as of 16:38, 29 January 2014
 | |
| Status | planned |
|---|---|
| Channels | 3/6/9/16 |
| Samplerate | 100/50/32/16MHz |
| Samplerate (state) | — |
| Triggers | ? |
| Min/max voltage | ? |
| Threshold voltage | ? |
| Memory | ? |
| Compression | ? |
| Website | aliexpress.com |
The XL-LOGIC16-100M is a USB-based, 16-channel logic analyzer with up to 100MHz sampling rate. It is labelled and sold as a Saleae Logic16 Clone, and comes with "modified" Saleae Logic software on a cdrom. The existing Saleae Logic16 support detects this device as an original, but fails to initialize the FPGA for capture.
See XL-LOGIC16-100M/Info for more details (such as lsusb -v output) about the device. (if ever desired)
Hardware
A single phillips head screw holds the case together. The parts selection seem to be almost identical to the WayEngineer_Saleae16 but that page doesn't have any internal photos for full comparison.
Most notable are the complete lack of test points or programming headers! There are some unpopulated resistor/capacitor pairs on the backside,
- FPGA: Xilinx Spartan-3A XC3S200A, 200K gates (datasheeet)
- USB interface chip: Cypress CY7C68013A-56PVXC (FX2LP) (datasheet)
- I2C EEPROM: 2Kbit Atmel 24C02B (markings: "ATMEL317 24C02BN SU27 D") (datasheet)
- 3.3V voltage regulator: Advanced Monolithic Systems AMS1117-3.3 (datasheet, older datasheet)
- 1.2V voltage regulator: Advanced Monolithic Systems AMS1117-1.2 (datasheet, older datasheet)
- Crystal: 24.000
Three LEDs, USB (green) COM (blue) and RUN (red) are on the board.
Photos
Firmware
Firmware and FPGA bitstream usage
You can use the sigrok-fwextract-saleae-logic16 tool to extract (from the "Logic" Linux binary) the FX2 firmware and the FPGA bitstreams, exactly as for a real Logic 16. Note, the md5sum of the fx2 firmware is identical to the original Saleae firmware, but the fpga bitstreams are different. Attempting to connect to this device with the "modified" fpga bitstream, which _works_ with the vendor supplied "modified" Logic software fails to load in sigrok, with a FPGA version mismatch. The fx2 firmware loads successfully, at least in as much as the LED blinks a heartbeat pattern as expected.
Protocol
Presumably as per Logic16