Difference between revisions of "TekPower TP4000ZC"
Jump to navigation
Jump to search
| (One intermediate revision by one other user not shown) | |||
| Line 7: | Line 7: | ||
| categories = CAT II (600V) | | categories = CAT II (600V) | ||
| connectivity = [[Device_cables#Digitek_DT4000ZC_cable|RS232]] | | connectivity = [[Device_cables#Digitek_DT4000ZC_cable|RS232]] | ||
| measurements = voltage, resistance, continuity, diode, capacitance, frequency, temperature, current, | | measurements = voltage, resistance, continuity, diode, capacitance, frequency, temperature, current, duty cycle | ||
| features = autorange, data hold, relative | | features = autorange, data hold, relative | ||
| website = [http://www.tekpower.us tekpower.us] | | website = [http://www.tekpower.us tekpower.us] | ||
| Line 20: | Line 20: | ||
'''Multimeter:''' | '''Multimeter:''' | ||
* '''Multimeter IC''': The microcontroller is an unidentifiable plastic blob (based on the communication protocol, probably a [[Multimeter_ICs#Fortune_Semiconductor_FS9721_LP3 | * '''Multimeter IC''': The microcontroller is an unidentifiable plastic blob (based on the communication protocol, probably a [[Multimeter_ICs#Fortune_Semiconductor_FS9721_LP3|Fortune Semiconductor FS9721_LP3]]) | ||
* LM358 opamp | * LM358 opamp | ||
* HEF4013BT flip-flop | * HEF4013BT flip-flop | ||
* The RS-232 connector is a standard 3.5m stereo jack, with the ring left unconnected. The transmitter is optically insulated from the rest of the device. | |||
The RS-232 connector is a standard 3.5m stereo jack, with the ring left unconnected. The transmitter is optically insulated from the rest of the device. | |||
'''Cable:''' | '''Cable:''' | ||
See [[Device_cables#Digitek_DT4000ZC_cable]]. | * See [[Device_cables#Digitek_DT4000ZC_cable]]. | ||
* The DB-9 connector has a loopback resistor between the RX and TX pins. | |||
The DB-9 connector has a loopback resistor between the RX and TX pins. | |||
== Photos == | == Photos == | ||
Latest revision as of 22:12, 21 January 2013
 | |
| Status | supported |
|---|---|
| Source code | serial-dmm |
| Counts | 4000 |
| IEC 61010-1 | CAT II (600V) |
| Connectivity | RS232 |
| Measurements | voltage, resistance, continuity, diode, capacitance, frequency, temperature, current, duty cycle |
| Features | autorange, data hold, relative |
| Website | tekpower.us |
The TekPower TP4000ZC is a 4000 counts, CAT II (600V) handheld digital multimeter with RS232 connectivity.
This multimeter is a rebadged Digitek DT4000ZC.
Hardware
Multimeter:
- Multimeter IC: The microcontroller is an unidentifiable plastic blob (based on the communication protocol, probably a Fortune Semiconductor FS9721_LP3)
- LM358 opamp
- HEF4013BT flip-flop
- The RS-232 connector is a standard 3.5m stereo jack, with the ring left unconnected. The transmitter is optically insulated from the rest of the device.
Cable:
- See Device_cables#Digitek_DT4000ZC_cable.
- The DB-9 connector has a loopback resistor between the RX and TX pins.
Photos
Multimeter:
Device, angle
Mugshot
Device, back
Package contents
Holster removed, front
Holster removed, back
Battery compartment
Rear cover
Front cover
Rear cover, PCB removed
PCB, front
PCB, back
Chip
HEF4013BT flip-flop
LM358 opamp
RS-232 optoisolation
RS-232 module
RS-232 PCB, bottom
RS-232 PCB, top
Cable:
See Device_cables#Digitek_DT4000ZC_cable.
Protocol
See Multimeter_ICs#Fortune_Semiconductor_FS9721_LP3.
User bit 2 is used to indicate temperature measurement in degrees Celsius.