Difference between revisions of "Pico Technology PicoScope 2204A"
Jump to navigation
Jump to search
(test) |
|||
| (2 intermediate revisions by the same user not shown) | |||
| Line 1: | Line 1: | ||
[[File:Picoscope 2204A.png|thumb|right|PicoScope 2204A.]] | |||
The [https://www.picotech.com/download/datasheets/picoscope-2000-series-data-sheet.pdf Pico Technology PicoScope 2204A] is a 2-channel USB-based PC oscilloscope (and spectrum analyzer and data logger and logic analyzer and function generator). | |||
The oscilloscope supports a bandwidth of 10MHz. The max. sampling rate is 100 MS/s. The memory depth is 8 kS. The function generator/signal generator and arbitrary waveform generator/AWG has a bandwidth of 100 kHz. | |||
See [[Pico Technology PicoScope 2204A/Info]] for more details (such as '''lsusb -vvv''' output) about the device. | |||
== Hardware == | |||
Active components are almost identical to [https://sigrok.org/wiki/Pico_Technology_PicoScope_2203 PicoScope 2203] | |||
* Xilinx Spartan XC3S250E (Field-Programmable Gate Arrays) | |||
* Cypress CY7C68013A-56PVXC (High-Speed USB Peripheral Controller) | |||
* ST 24C02 (2kB EEPROM) | |||
* HC4052 (Dual 4-ch Multiplexer) | |||
* Analog Devices AD8132 (High Speed Differential Amplifier) | |||
* Analog Devices AD9288 (Dual 8-bit ADC) | |||
* Comus 3570-1332-053 (Reed Relais) | |||
* Maxim MAX889S (Inverting Charge Pump) | |||
== Photos == | |||
<gallery> | |||
File:PicoScope_2204A_front.jpg|<small>Front</small> | |||
File:PicoScope_2204A_back.jpg|<small>Back</small> | |||
File:PicoScope_2204A_pcb_front.jpg|<small>PCB front</small> | |||
File:PicoScope_2204A_pcb_back.jpg|<small>PCB back</small> | |||
</gallery> | |||
== Protocol == | |||
=== Firmware === | |||
The usual Cypress FX2 firmware upload mechanism is used to upload a special FX2 firmware. | |||
=== Start acquisition === | |||
=== Sample format === | |||
=== End acquisition === | |||
=== Triggers === | |||
=== Voltage ranges === | |||
== Resources == | |||
* [https://www.picotech.com/download/datasheets/picoscope-2000-series-data-sheet.pdf Datasheet] | |||
* [https://www.picotech.com/downloads Vendor software etc. download page] | |||
* [https://www.picotech.com/download/manuals/picoscope-2000-series-a-api-programmers-guide.pdf Vendor oscilloscope programmer's guide] | |||
* [https://www.picotech.com/download/manuals/TriggeringAPicoScopeSignalGeneratorUsingThePicoScopeAPIFunctions.pdf Vendor signal generator programmer's guide] | |||
[[Category:Device]] | |||
[[Category:Oscilloscope]] | |||
[[Category:Planned]] | |||
Latest revision as of 13:28, 4 January 2020
The Pico Technology PicoScope 2204A is a 2-channel USB-based PC oscilloscope (and spectrum analyzer and data logger and logic analyzer and function generator).
The oscilloscope supports a bandwidth of 10MHz. The max. sampling rate is 100 MS/s. The memory depth is 8 kS. The function generator/signal generator and arbitrary waveform generator/AWG has a bandwidth of 100 kHz.
See Pico Technology PicoScope 2204A/Info for more details (such as lsusb -vvv output) about the device.
Hardware
Active components are almost identical to PicoScope 2203
- Xilinx Spartan XC3S250E (Field-Programmable Gate Arrays)
- Cypress CY7C68013A-56PVXC (High-Speed USB Peripheral Controller)
- ST 24C02 (2kB EEPROM)
- HC4052 (Dual 4-ch Multiplexer)
- Analog Devices AD8132 (High Speed Differential Amplifier)
- Analog Devices AD9288 (Dual 8-bit ADC)
- Comus 3570-1332-053 (Reed Relais)
- Maxim MAX889S (Inverting Charge Pump)
Photos
Front
Back
PCB front
PCB back
Protocol
Firmware
The usual Cypress FX2 firmware upload mechanism is used to upload a special FX2 firmware.