Difference between revisions of "Saleae Logic Pro 8"
m (→Hardware) |
Uwe Hermann (talk | contribs) (Not actually supported currently.) |
||
| Line 2: | Line 2: | ||
| image = [[File:Saleae_logic_pro_8-bottom.png|180px]] | | image = [[File:Saleae_logic_pro_8-bottom.png|180px]] | ||
| name = Saleae Logic Pro 8 | | name = Saleae Logic Pro 8 | ||
| status = | | status = planned | ||
| source_code_dir = saleae-logic-pro | | source_code_dir = saleae-logic-pro | ||
| channels = 8 | | channels = 8 | ||
| Line 74: | Line 74: | ||
[[Category:Oscilloscope]] | [[Category:Oscilloscope]] | ||
[[Category:Mixed-signal oscilloscope]] | [[Category:Mixed-signal oscilloscope]] | ||
[[Category: | [[Category:Planned]] | ||
Revision as of 10:50, 29 October 2018
 | |
| Status | planned |
|---|---|
| Source code | saleae-logic-pro |
| Channels | 8 |
| Samplerate | 500/100MHz (4ch/8ch) |
| Samplerate (state) | — |
| Triggers | none (SW-only) |
| Min/max voltage | -25 — 25V tolerant |
| Threshold voltage | 1.2V to 12V digital, -10 to 10V analog |
| Memory | none |
| Compression | yes |
| Website | saleae.com |
The Saleae Logic Pro 8 is a USB 3.0-based, 8-channel logic analyzer with 500/100MHz sampling rate (at 4/8 enabled channels) and analog sampling support on all 8 channels.
It is part of the second-generation Saleae Logic series, which consists of the Logic 4, Logic 8, Logic Pro 8 and Logic Pro 16. See Saleae Logic and Saleae Logic8 for the predecessor products.
The case requires a Torx TX6 screwdriver to open.
See Saleae Logic Pro 8/Info for more details (such as lsusb -v output) about the device.
Note: Saleae Logic Pro 8 support in sigrok should be considered experimental for now. Only the logic analyzer parts are currently implemented (analog sampling is not).
Hardware
- FPGA: Xilinx Spartan-6 XC6SLX9, 9,152 logic elements (family overview) (datasheet)
- USB interface chip: Cypress CYUSB3014-BZXI (FX3) (datasheet)
- ADCs: 1x Exar CDK8307B (datasheet) (seems to have same I2C reg mapping than HMCAD1100 used in Saleae Logic Pro 16)
- 32Kbit I2C EEPROM: 24C32A (datasheet)
- 6x amplifiers: Analog Devices ADA4891-4 (datasheet)
Photos
Device, bottom
PCB, top
PCB, bottom
XC6SLX9 IC
CYUSB3014-BZXI IC
CDK8307 IC
24c32A IC
ADA4891-4 IC
Firmware
You can use the sigrok-fwextract-saleae-logic16 (sic!) tool to extract (from the "Logic" Linux binary; tested with the Saleae 1.2.10 software) the FX3 firmware and the FPGA bitstreams required for using the Saleae Logic Pro 16:
$ sigrok-fwextract-saleae-logic16 Logic saved 5217 bytes to saleae-logic16-fx2.fw saved 149516 bytes to saleae-logic16-fpga-18.bitstream saved 149516 bytes to saleae-logic16-fpga-33.bitstream saved 178702 bytes from 46 blobs to saleae-logicpro16-fx3.fw saved 178702 bytes from 46 blobs to saleae-logicpro8-fx3.fw saved 465028 bytes to saleae-logicpro16-fpga.bitstream saved 341160 bytes to saleae-logicpro8-fpga.bitstream
Copy these files to the directory where your libsigrok installation expects them (usually /usr/local/share/sigrok-firmware) and they will be found and used automatically by the libsigrok saleae-logic-pro driver.
Note that sigrok-util (commit 20e302a2) only works Saleae Logic software up to 1.2.10 !
Resources
- User guide
- Download vendor software
- Vendor software version 1.2.10 32-bit (needed to extract firmwares)
- SDKs