Hantek DSO4004C series/Info
Jump to navigation
Jump to search
lsusb DSO4104C
$ lsusb -v -d 049f:505c
Bus 002 Device 109: ID 049f:505c Compaq Computer Corp. NOT defined
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 2.00
bDeviceClass 0
bDeviceSubClass 0
bDeviceProtocol 0
bMaxPacketSize0 64
idVendor 0x049f Compaq Computer Corp.
idProduct 0x505c
bcdDevice 2.30
iManufacturer 1 NOT defined
iProduct 2 NOT defined
iSerial 3 CN1943002003936
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 0x0027
bNumInterfaces 1
bConfigurationValue 1
iConfiguration 0
bmAttributes 0xc0
Self Powered
MaxPower 500mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 3
bInterfaceClass 254 Application Specific Interface
bInterfaceSubClass 3 Test and Measurement
bInterfaceProtocol 0
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x81 EP 1 IN
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0200 1x 512 bytes
bInterval 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x02 EP 2 OUT
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0200 1x 512 bytes
bInterval 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x83 EP 3 IN
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x0040 1x 64 bytes
bInterval 2
Device Qualifier (for other device speed):
bLength 10
bDescriptorType 6
bcdUSB 2.00
bDeviceClass 0
bDeviceSubClass 0
bDeviceProtocol 0
bMaxPacketSize0 64
bNumConfigurations 1
can't get debug descriptor: Resource temporarily unavailable
Device Status: 0x0000
(Bus Powered)
bootlog DSO4104C
OM*** Warning - bad CRC, using default environment
##### EmbedSky BIOS for SKY2416/TQ2416 #####
This Board: SDRAM is 64MB; Press Space key to Download Mode.!
NAND read: device 0 offset 0x380000, size 0x800
2048 bytes read: OK
**************************normal start*******************************
NAND erase: device 0 offset 0x380000, size 0x80000
Erasing at 0x3e0000 -- 100% complete.
OK
NAND write: device 0 offset 0x380000, size 0x800
Writing data at 0x380800 -- 100% complete.
2048 bytes written: OK
NAND read: device 0 offset 0x380000, size 0x800
2048 bytes read: OK
Saving Environment to NAND...
Erasing Nand...
Warning: Erase size 0x00004000 smaller than one erase block 0x00020000
Erasing 0x00020000 instead
Erasing at 0x80000 -- 100% complete.
Writing to Nand... done
NAND read: device 0 offset 0x400000, size 0x400000
4194304 bytes read: OK
Boot with zImage
Starting kernel ...
Uncompressing Linux... done, booting the kernel.
Linux version 3.2.35 (root@zgt) (gcc version 4.3.3 (Sourcery G++ Lite 2009q1-176) ) #122 PREEMPT Fri Sep 20 23:29:30 CST 2019
CPU: ARM926EJ-S [41069265] revision 5 (ARMv5TEJ), cr=00053177
CPU: VIVT data cache, VIVT instruction cache
Machine: SMDK2416
Ignoring unrecognised tag 0x54410008
Memory policy: ECC disabled, Data cache writeback
CPU S3C2416/S3C2450 (id 0x32450003)
S3C24XX Clocks, Copyright 2004 Simtec Electronics
CPU: MPLL on 800.000 MHz, cpu 400.000 MHz, mem 133.333 MHz, pclk 66.666 MHz
CPU: EPLL on 96.000 MHz, usb-bus 48.000 MHz
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 16256
Kernel command line: noinitrd ubi.mtd=5 ubi.mtd=6 root=ubi0:rootfs rootfstype=ubifs init=/linuxrc console=ttySAC0 lcd=X480Y272
PID hash table entries: 256 (order: -2, 1024 bytes)
Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
Memory: 64MB = 64MB total
Memory: 58944k/58944k available, 6592k reserved, 0K highmem
Virtual kernel memory layout:
vector : 0xffff0000 - 0xffff1000 ( 4 kB)
fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB)
vmalloc : 0xc4800000 - 0xf6000000 ( 792 MB)
lowmem : 0xc0000000 - 0xc4000000 ( 64 MB)
modules : 0xbf000000 - 0xc0000000 ( 16 MB)
.text : 0xc0008000 - 0xc03fc000 (4048 kB)
.init : 0xc03fc000 - 0xc041b000 ( 124 kB)
.data : 0xc041c000 - 0xc05b6200 (1641 kB)
.bss : 0xc05b6224 - 0xc05d3ffc ( 120 kB)
SLUB: Genslabs=13, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
NR_IRQS:107
irq: clearing subpending status 00000002
Calibrating delay loop... 198.45 BogoMIPS (lpj=496128)
pid_max: default: 4096 minimum: 301
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
NET: Registered protocol family 16
S3C2416: Initializing architecture
S3C2416: IRQ Support
S3C24XX DMA Driver, Copyright 2003-2006 Simtec Electronics
DMA channel 0 at c4804000, irq 88
DMA channel 1 at c4804100, irq 89
DMA channel 2 at c4804200, irq 90
DMA channel 3 at c4804300, irq 91
DMA channel 4 at c4804400, irq 92
DMA channel 5 at c4804500, irq 93
bio: create slab <bio-0> at 0
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
s3c-i2c s3c2410-i2c: slave address 0x10
s3c-i2c s3c2410-i2c: bus frequency set to 9 KHz
s3c-i2c s3c2410-i2c: i2c-0: S3C I2C adapter
Advanced Linux Sound Architecture Driver Version 1.0.24.
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 2048 (order: 2, 16384 bytes)
TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
TCP: Hash tables configured (established 2048 bind 2048)
TCP reno registered
NET: Registered protocol family 1
RPC: Registered named UNIX socket transport module.
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
RPC: Registered tcp NFSv4.1 backchannel transport module.
s3c-adc s3c24xx-adc: attached adc driver
msgmni has been set to 115
io scheduler noop registered (default)
io scheduler cfq registered
s3c-fb s3c-fb: window 0: fb
s3c-fb s3c-fb: LCD type is TN83 800*480, default_bpp=16, pixclock=5
s3c-fb s3c-fb: window 1: fb
s3c-fb s3c-fb: LCD type is TN83 800*480, default_bpp=16, pixclock=5
s3c2440-uart.0: ttySAC0 at MMIO 0x50000000 (irq = 70) is a S3C2440
console [ttySAC0] enabled
s3c2440-uart.1: ttySAC1 at MMIO 0x50004000 (irq = 73) is a S3C2440
s3c2440-uart.2: ttySAC2 at MMIO 0x50008000 (irq = 76) is a S3C2440
s3c2440-uart.3: ttySAC3 at MMIO 0x5000c000 (irq = 94) is a S3C2440
loop: module loaded
S3C24XX NAND Driver, (c) 2004 Simtec Electronics
info->cpu_type=3, tacls_max=8
s3c24xx-nand s3c2416-nand: Tacls=3, 22ns Twrph0=7 52ns, Twrph1=3 22ns
s3c24xx-nand s3c2416-nand: System booted from NAND
s3c24xx-nand s3c2416-nand: NAND ECC disabled
NAND device: Manufacturer ID: 0xc8, Chip ID: 0xd1 (ISSI NAND 128MiB 3,3V 8-bit)
NAND_ECC_NONE selected by board driver. This is not recommended!
Scanning device for bad blocks
Bad eraseblock 588 at 0x000004980000
Bad eraseblock 982 at 0x000007ac0000
Creating 9 MTD partitions on "NAND":
0x000000000000-0x000000100000 : "uboot"
0x000000100000-0x000000180000 : "params"
0x000000180000-0x000000380000 : "logo"
0x000000380000-0x000000400000 : "misc"
0x000000400000-0x000000800000 : "kernel"
0x000000800000-0x000003a00000 : "rootfs"
0x000003a00000-0x000004e00000 : "config"
0x000004e00000-0x000005200000 : "kernel_bk"
0x000005200000-0x000008000000 : "recover"
UBI: attaching mtd5 to ubi0
UBI: physical eraseblock size: 131072 bytes (128 KiB)
UBI: logical eraseblock size: 126976 bytes
UBI: smallest flash I/O unit: 2048
UBI: VID header offset: 2048 (aligned 2048)
UBI: data offset: 4096
UBI: max. sequence number: 858
UBI: attached mtd5 to ubi0
UBI: MTD device name: "rootfs"
UBI: MTD device size: 50 MiB
UBI: number of good PEBs: 400
UBI: number of bad PEBs: 0
UBI: number of corrupted PEBs: 0
UBI: max. allowed volumes: 128
UBI: wear-leveling threshold: 4096
UBI: number of internal volumes: 1
UBI: number of user volumes: 1
UBI: available PEBs: 0
UBI: total number of reserved PEBs: 400
UBI: number of PEBs reserved for bad PEB handling: 4
UBI: max/mean erase counter: 5/2
UBI: image sequence number: 0
UBI: background thread "ubi_bgt0d" started, PID 341
UBI: attaching mtd6 to ubi1
UBI: physical eraseblock size: 131072 bytes (128 KiB)
UBI: logical eraseblock size: 126976 bytes
UBI: smallest flash I/O unit: 2048
UBI: VID header offset: 2048 (aligned 2048)
UBI: data offset: 4096
UBI: max. sequence number: 692
UBI: attached mtd6 to ubi1
UBI: MTD device name: "config"
UBI: MTD device size: 20 MiB
UBI: number of good PEBs: 159
UBI: number of bad PEBs: 1
UBI: number of corrupted PEBs: 0
UBI: max. allowed volumes: 128
UBI: wear-leveling threshold: 4096
UBI: number of internal volumes: 1
UBI: number of user volumes: 1
UBI: available PEBs: 0
UBI: total number of reserved PEBs: 159
UBI: number of PEBs reserved for bad PEB handling: 2
UBI: max/mean erase counter: 7/5
UBI: image sequence number: 0
UBI: background thread "ubi_bgt1d" started, PID 344
ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
s3c2410-ohci s3c2410-ohci: S3C24XX OHCI
s3c2410-ohci s3c2410-ohci: new USB bus registered, assigned bus number 1
s3c2410-ohci s3c2410-ohci: irq 42, io mem 0x49000000
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
usbcore: registered new interface driver usblp
usbcore: registered new interface driver uas
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
samsung-ts s3c2416-ts: driver attached, registering input device
input: S3C24XX TouchScreen as /devices/virtual/input/input0
S3C24XX RTC, (c) 2004,2006 Simtec Electronics
s3c-rtc s3c2410-rtc: rtc disabled, re-enabling
s3c-rtc s3c2410-rtc: rtc core: registered s3c as rtc0
i2c /dev entries driver
S3C2410 Watchdog Timer, (c) 2004 Simtec Electronics
s3c2410-wdt s3c2410-wdt: watchdog inactive, reset disabled, irq disabled
sdhci: Secure Digital Host Controller Interface driver
sdhci: Copyright(c) Pierre Ossman
s3c-sdhci s3c-sdhci.1: clock source 0: hsmmc (133333333 Hz)
s3c-sdhci s3c-sdhci.1: clock source 1: hsmmc (133333333 Hz)
s3c-sdhci s3c-sdhci.1: clock source 2: hsmmc-if (24000000 Hz)
mmc0: SDHCI controller on samsung-hsmmc [s3c-sdhci.1] using ADMA
usbcore: registered new interface driver usbhid
usbhid: USB HID core driver
S3C24XX_UDA134X SoC Audio driver
S3C24XX_UDA134X SoC Audio: l3 data pin already in use
s3c24xx_uda134x: probe of s3c24xx_uda134x.0 failed with error -16
ALSA device list:
No soundcards found.
TCP cubic registered
NET: Registered protocol family 17
Registering the dns_resolver key type
s3c-rtc s3c2410-rtc: setting system clock to 2020-04-10 08:59:58 UTC (1586509198)
UBIFS: recovery needed
UBIFS: recovery completed
UBIFS: mounted UBI device 0, volume 0, name "rootfs"
UBIFS: file system size: 48377856 bytes (47244 KiB, 46 MiB, 381 LEBs)
UBIFS: journal size: 9023488 bytes (8812 KiB, 8 MiB, 72 LEBs)
UBIFS: media format: w4/r0 (latest is w4/r0)
UBIFS: default compressor: lzo
UBIFS: reserved for root: 0 bytes (0 KiB)
VFS: Mounted root (ubifs filesystem) on device 0:10.
Freeing init memory: 124K
UBIFS: recovery needed
UBIFS: recovery completed
UBIFS: mounted UBI device 1, volume 0, name "config"
UBIFS: file system size: 18030592 bytes (17608 KiB, 17 MiB, 142 LEBs)
UBIFS: journal size: 9023488 bytes (8812 KiB, 8 MiB, 72 LEBs)
UBIFS: media format: w4/r0 (latest is w4/r0)
UBIFS: default compressor: lzo
UBIFS: reserved for root: 0 bytes (0 KiB)
Please press Enter to activate this console. dso-iobank: install ok
0x603
gpio_major_n = 6, io_minor_n = 3, output 0
0x408
gpio_major_n = 4, io_minor_n = 8, output 1
AFG3050 fpga configure init
adc init
TQ2416 ADC driver
tq2416_backlight_init_timer0:0x200, 0x2
bkl tq2416-backlight initialized done...
dso-buzzer s3c2416-beep initialized done...
user file is /lib/firmware/dso4000.bit
nstatus0 :0x0
nstatus1 :0x1
fpga state :0x1
file len is 460418
FPGA CONFIGURE DATA DOWN finish.0x1, 0
FPGA CONFIGURE ok.
fpga bank 11811
input: dso_kbd as /devices/virtual/misc/dso-fpga/input1
dso-fpga: install ok
make snd node.
dm9000 Ethernet Driver, V1.31
dm9000 dm9000: read wrong id 0x2b2a2928
dm9000 dm9000: read wrong id 0x2b2a2928
dm9000 dm9000: read wrong id 0x2b2a2928
dm9000 dm9000: read wrong id 0x2b2a2928
dm9000 dm9000: read wrong id 0x2b2a2928
dm9000 dm9000: read wrong id 0x2b2a2928
dm9000 dm9000: read wrong id 0x2b2a2928
dm9000 dm9000: read wrong id 0x2b2a2928
dm9000 dm9000: wrong id: 0x2b2a2928
dm9000 dm9000: not found (-19).
ifconfig: SIOCSIFADDR: No such device
Erasing 128 Kibyte @ 80000 - 100% complete.
--------------------------------------------------------------------------------
start
--------------------------------------------------------------------------------
reg is 0x2, val is 0x1
reg is 0x2, val is 0x3
reg is 0x3, val is 0x0
reg is 0x4, val is 0x39
reg is 0x7, val is 0x3f
reg is 0x8, val is 0x8
reg is 0x9, val is 0x80
reg is 0xd, val is 0x8
reg is 0xf, val is 0x1b
reg is 0x10, val is 0x20
reg is 0x11, val is 0x5c
reg is 0x12, val is 0x40
reg is 0x13, val is 0x2a
reg is 0x14, val is 0x11
reg is 0x15, val is 0x11
reg is 0x16, val is 0xe0
reg is 0x17, val is 0x8
reg is 0x19, val is 0x1f
reg is 0x1a, val is 0x8
reg is 0x1b, val is 0x23
reg is 0x1c, val is 0x20
reg is 0x1d, val is 0x20
reg is 0x1f, val is 0x28
reg is 0x20, val is 0x80
reg is 0x21, val is 0x12
reg is 0x22, val is 0x58
reg is 0x23, val is 0x74
reg is 0x25, val is 0x1
reg is 0x26, val is 0x4
reg is 0x37, val is 0x20
reg is 0x39, val is 0x20
reg is 0x3b, val is 0x20
reg is 0x41, val is 0x9a
reg is 0x4d, val is 0x3
reg is 0x4e, val is 0x50
reg is 0x4f, val is 0xda
reg is 0x50, val is 0x74
reg is 0x51, val is 0x4b
reg is 0x52, val is 0x12
reg is 0x53, val is 0x13
reg is 0x55, val is 0xe5
reg is 0x5e, val is 0x80
reg is 0x69, val is 0x64
reg is 0x77, val is 0x3
reg is 0x7d, val is 0x62
reg is 0x4, val is 0x38
reg is 0x6, val is 0x71
reg is 0x3, val is 0x0
reg is 0x3, val is 0x0
reg is 0x3, val is 0x0
reg is 0x3, val is 0x0
reg is 0x3, val is 0x0
reg is 0x6, val is 0x70
reg is 0x2, val is 0x2
reg is 0x2, val is 0x3
reg is 0x4, val is 0x0
fpga_ctl_kbd_open:1: (null)
fpga_ctl_kbd_open:2:c3b497a0
open kbd dso_kbd successful
dbus is valid and addr is unix:path=/tmp/dbus-lmSHWwAP0O,guid=7b4394ba4a0c7c3399a88a975e903592
system info do begin
init system info ...
read_sytem_infos_from_file:1:100M$DSO4104C
read_sytem_infos_from_file:2:DSO4104C,100M
init system info over
system info do end
anolis_init:machine is 100M
anolis_init:after adjust intensity
anolis_init:over
fpga_init:0x40011000
pll is locked
gpio_major_n = 0, io_minor_n = 2, output 0
gpio_major_n = 0, io_minor_n = 3, output 0
gpio_major_n = 0, io_minor_n = 4, output 0
gpio_major_n = 0, io_minor_n = 8, output 0
gpio_major_n = 10, io_minor_n = 12, output 1
util_helper_load_setup:0, 0
init_calibration_result: in:/config/root/cali.dat
init_calibration_result:1:12345678, 12345678
init_calibration_result:2:101, 101
init_calibration_result:3:89abcdef, 89abcdef
init_calibration_result: has calibration result
measure_helper_set_one_chn_all_only:0
fpga pll is ok
acq_dot_nm_of_timerange =4000,time_range=80000000000,dso_acq.dot_factor =1,sample_rate =50000.000000
dso_acq_control:1:2056, 2056,1800
dso_acq_control:2:3856, 256
dso_acq_control:3:9640000, 680000
dso_acq_control:4:after= 9640000, before= 680000
acq_dot_nm_of_timerange =4000,time_range=80000000000,dso_acq.dot_factor =1,sample_rate =50000.000000
dso_acq_control:1:2056, 2056,1800
dso_acq_control:2:3856, 256
dso_acq_control:3:9640000, 680000
dso_acq_control:4:after= 9640000, before= 680000
util_thread_start_with_sched_priority:thread 0x9ed690 is running
dds_calibration_load:success,read_data = 40
dds_calibrate_uniformlize_offset:0x100011
dds_calibrate_uniformlize_offset:-0.000526, 3.909857, -3.903463, 0.000000, 1.000000, 0.255973, -0.000526
dds_calibrate_uniformlize_amp:0x100011
dds_calibrate_uniformlize_amp:7.813320, 1.500000
**********amp_value = 0.191980,amp = 393,cal_value =1.000000
CN*********
android_init_functions tmc init
android_usb gadget: android_usb ready
s3c-hsudc s3c-hsudc: bound driver android_usb
android_enable_function: tmc enabled
android_bind_enabled_functions bind name: tmc
dual speed tmc: IN/ep1in, OUT/ep2out, INTep3in/
dso_wave_plot_init_normal:0xddba0:770,400
anolis_picture_width:21 picture!=NULL failed.
anolis_picture_width:21 picture!=NULL failed.
anolis_picture_width:21 picture!=NULL failed.
anolis_picture_width:21 picture!=NULL failed.
anolis_picture_width:21 picture!=NULL failed.
fpga_ctl_kbd_event:in
fpga_ctl_kbd_event:17, 3, 1, 4fpga_ctl_kbd_event:in
fpga_ctl_kbd_event:17, 6, 1, 24fpga_ctl_kbd_event:in
fpga_ctl_kbd_event:17, 2, 1, 26fpga_ctl_kbd_event:in
fpga_ctl_kbd_event:17, 7, 1, 66update_trigtime:0.036000, 36ms
util_thread_start_with_sched_priority:thread 0xa06b70 is running
unix:path=/tmp/dbus-lmSHWwAP0O,guid=7b4394ba4a0c7c3399a88a975e903592
[root@Hantek ~]#ls
bin etc model spi_pll.data var
config lib proc sys version
dev linuxrc root tmp www
dso mnt sbin usr
[root@Hantek ~]#mount
rootfs on / type rootfs (rw)
ubi0:rootfs on / type ubifs (rw,relatime)
proc on /proc type proc (rw,relatime)
tmpfs on /tmp type tmpfs (rw,relatime)
sysfs on /sys type sysfs (rw,relatime)
tmpfs on /dev type tmpfs (rw,relatime)
tmpfs on /var type tmpfs (rw,relatime)
devpts on /dev/pts type devpts (rw,relatime,mode=600,ptmxmode=000)
ubi1:config on /config type ubifs (rw,relatime)
[root@Hantek ~]#uname -a
Linux dso4000 3.2.35 #122 PREEMPT Fri Sep 20 23:29:30 CST 2019 armv5tejl GNU/Linux
[root@Hantek ~]#cat /proc/cpuinfo
Processor : ARM926EJ-S rev 5 (v5l)
BogoMIPS : 198.45
Features : swp half fastmult edsp java
CPU implementer : 0x41
CPU architecture: 5TEJ
CPU variant : 0x0
CPU part : 0x926
CPU revision : 5
Hardware : SMDK2416
Revision : 0000
Serial : 0000000000000000
[root@Hantek ~]#cat /proc/mtd
dev: size erasesize name
mtd0: 00100000 00020000 "uboot"
mtd1: 00080000 00020000 "params"
mtd2: 00200000 00020000 "logo"
mtd3: 00080000 00020000 "misc"
mtd4: 00400000 00020000 "kernel"
mtd5: 03200000 00020000 "rootfs"
mtd6: 01400000 00020000 "config"
mtd7: 00400000 00020000 "kernel_bk"
mtd8: 02e00000 00020000 "recover"
mtd9: 02f78000 0001f000 "rootfs"
mtd10: 01287000 0001f000 "config"
[root@Hantek ~]#cat /proc/cmdline
noinitrd ubi.mtd=5 ubi.mtd=6 root=ubi0:rootfs rootfstype=ubifs init=/linuxrc console=ttySAC0 lcd=X480Y272
[root@Hantek ~]#
[root@Hantek ~]#cat /config/root/system.inf
[machine]
Model=250M$DSO4254C
Vendor=Hantek
Product=DSO
Manufacturer=hantek
Serial=CN*********
[version]
Pcb=501.001.001.000.000.000.0
Keyboard=1
[language]
Lans=163190
Language=0
[add]
Start=39
Update=0
[root@Hantek ~]#