Difference between revisions of "User talk:Mrnuke"
| Line 26: | Line 26: | ||
It is clear at this point that the protocol on the RS-232 side is not the same as the protocol used on the IR side. This raises an interesting question: Can the protocol be reversed-engineered and implemented as a simple UART? If the IR encoding is a simple UART, then it is feasible. A "brymen-dmm-raw" driver could provide users with a quick way to put together a circuit and communicate with their Brymen. | It is clear at this point that the protocol on the RS-232 side is not the same as the protocol used on the IR side. This raises an interesting question: Can the protocol be reversed-engineered and implemented as a simple UART? If the IR encoding is a simple UART, then it is feasible. A "brymen-dmm-raw" driver could provide users with a quick way to put together a circuit and communicate with their Brymen. | ||
==== Connector pinout ==== | |||
{| border="0" style="font-size: smaller" class="alternategrey sigroktable" | |||
|- | |||
! style="width: 8em;" | RS232 pin | |||
! style="width: 8em;" | Conductor color | |||
|- | |||
| 1 - DCD | |||
| NC | |||
|- | |||
! style="background-color:red" | 2 - Rx | |||
! style="background-color:red" | Red | |||
|- | |||
! style="background-color:yellow" | 3 - Tx | |||
! style="background-color:yellow" | Yellow | |||
|- | |||
! style="background-color:green" | 4 - DTR | |||
! style="background-color:green" | Green | |||
|- | |||
! style="background-color:blue" | 5 - GND | |||
! style="background-color:blue" | Blue | |||
|- | |||
! style="background-color:gray" | 6 - DSR | |||
! style="background-color:gray" | Gray | |||
|- | |||
! style="background-color:white" | 7 - RTS | |||
! style="background-color:white" | White | |||
|- | |||
! style="backgorund-color:black" | 8 - CTS | |||
! style="background-color:black" | Black | |||
|- | |||
| 9 - RI | |||
| NC | |||
|} | |||
=== Photos === | === Photos === | ||
Revision as of 20:34, 8 December 2012
BM857 PC interface cable
I'm trying to build a PC interface cable for my Brymen BM857. I have used Radioshack 276-142 IR diode and photo-transistor set, and a PL2303 USB to serial converter.
If you have a real cable you'd like to donate, hop on to #sigrok and contact me.
Info
This is an experimental homebrew design. It does NOT work. The manufacturer's cable contains a PIC microcontroller that communicates with the PC, and multimeter. The data sent through the serial port is not what the DMM receives/sends. Any straight cable will not work.
It is unclear if the IR protocol is a simple UART, or is pulse-width based, or if it uses any other encoding.
Schematic
Photos
The IR diode and phototransistor are prominent on the board
Board being held in place by the rubber holster
Brymen BC-58Xa interface cable
This is the official interface cable sold by Brymen. It works with the BM857a and BM859a, but does not work with thw non-a models.
Reverse engineering the cable
It is clear at this point that the protocol on the RS-232 side is not the same as the protocol used on the IR side. This raises an interesting question: Can the protocol be reversed-engineered and implemented as a simple UART? If the IR encoding is a simple UART, then it is feasible. A "brymen-dmm-raw" driver could provide users with a quick way to put together a circuit and communicate with their Brymen.
Connector pinout
| RS232 pin | Conductor color
|
|---|---|
| 1 - DCD | NC |
| 2 - Rx | Red |
| 3 - Tx | Yellow |
| 4 - DTR | Green |
| 5 - GND | Blue |
| 6 - DSR | Gray |
| 7 - RTS | White |
| 8 - CTS | Black |
| 9 - RI | NC |
Photos
These are from the Extech SW810a kit. The components are all manufactured by Brymen, and carry the Brymen part numbers.
Kit contents (software disc not shown)
BC-58Xa DB9 connector
BC-58Xa DMM connector
BUA2303 USB-to-serial converter
BUA2303 USB-to-serial converter, back
BUA2303 USB-to-serial converter, bottom
IR side, opened
IR side casing
IR side PCB, top
IR side PCB, botoom
BUA2303 PCB, top
BUA2303 PCB, bottom
