Difference between revisions of "Rigol DS1000Z series"
Jump to navigation
Jump to search
(Created the page for Rigol DS1000Z series (based on DS2000 series page)) |
Whitequark (talk | contribs) |
||
| (6 intermediate revisions by 4 users not shown) | |||
| Line 1: | Line 1: | ||
{{Infobox oscilloscope | {{Infobox oscilloscope | ||
| image = | | image = [[File:Rigol DS1074Z front.png|180px]] | ||
| name = Rigol DS1000Z Series | | name = Rigol DS1000Z Series | ||
| status = | | status = supported | ||
| source_code_dir = | | source_code_dir = | ||
| channels = 4 | | channels = 4 | ||
| Line 17: | Line 17: | ||
}} | }} | ||
The [http://www.rigolna.com/products/digital-oscilloscopes/ds1000Z/ Rigol DS1000Z Series] are 4-channel oscilloscopes with an analog bandwidth of 50-100MHz and | The [http://www.rigolna.com/products/digital-oscilloscopes/ds1000Z/ Rigol DS1000Z Series] are 4-channel oscilloscopes with an analog bandwidth of 50-100MHz and 1GSa/s maximum sampling rate. | ||
| Line 25: | Line 25: | ||
!Model || Bandwidth | !Model || Bandwidth | ||
|- | |- | ||
|| DS1054Z || 50MHz | || [[Rigol DS1054Z]] || 50MHz | ||
|- | |- | ||
|| DS1074Z || 70MHz | || [[Rigol DS1074Z]] || 70MHz | ||
|- | |- | ||
|| DS1104Z || 100MHz | || DS1104Z || 100MHz | ||
| Line 34: | Line 34: | ||
== Protocol == | == Protocol == | ||
The device uses [[USBTMC]] or LXI via its | The device uses [[USBTMC]] or LXI via its Ethernet port for communication with a host PC. The protocol is based on SCPI commands. | ||
If you're getting persistent command errors when attempting to capture via Ethernet (try running sigrok-cli with <tt>-l 5</tt>), make sure your oscilloscope runs at least firmware version 00.04.03.02. | |||
== Resources == | == Resources == | ||
| Line 45: | Line 47: | ||
[[Category:Device]] | [[Category:Device]] | ||
[[Category:Oscilloscope]] | [[Category:Oscilloscope]] | ||
Latest revision as of 14:42, 4 March 2016
 | |
| Status | supported |
|---|---|
| Channels | 4 |
| Samplerate | 1GSa/s (1ch), 500MSa/s (2ch), 250MSa/s (3 or 4 ch) |
| Analog bandwidth | 50-100MHz (depending on model) |
| Vertical resolution | 8bits |
| Triggers | edge, pulse, runt, windows, nth edge, slope, video, pattern, delay, timeout, duration, setup/hold, RS232/UART, I²C, SPI |
| Input impedance | 1MΩ‖13pF 300V RMS CAT I |
| Memory | 12/24Mpts (mode/ch-dependent) |
| Display | 7 Inch WVGA (800x480) 160,000 colours |
| Connectivity | USB host/device, ethernet (LXI), trigger out, pass/fail out |
| Features | math: +, —, x, /, FFT, vertical sensitivity: 1 mV/div to 10 V/div |
| Website | rigolna.com |
The Rigol DS1000Z Series are 4-channel oscilloscopes with an analog bandwidth of 50-100MHz and 1GSa/s maximum sampling rate.
Devices
| Model | Bandwidth |
|---|---|
| Rigol DS1054Z | 50MHz |
| Rigol DS1074Z | 70MHz |
| DS1104Z | 100MHz |
Protocol
The device uses USBTMC or LXI via its Ethernet port for communication with a host PC. The protocol is based on SCPI commands.
If you're getting persistent command errors when attempting to capture via Ethernet (try running sigrok-cli with -l 5), make sure your oscilloscope runs at least firmware version 00.04.03.02.