Agilent U1232A
The Agilent U123xA are a series of low-cost 6000-count handheld digital multimeters. PC connectivity is via an IR port.
Hardware
- Renesas 78K0/LF3 8-bit microcontroller with 60K flash and 2K RAM on board.
Photos
Multimeter:
Back
PCB, top
White silkscreen (LCD background)
PCB, bottom
PCB detail
Microcontroller
IR-USB cable:
See Multimeter cables#Agilent_U1173A.
IR-bluetooth interface:
See Multimeter cables#Agilent_U1177A.
Protocol
IDN
Sending the command *IDN? causes the device to return a comma-separated four-field string, compatible with the identical GPIB command. The four fields are vendor name, model name, serial number and version:
Agilent Technologies,U1232A,MY52020136,V1.00
CONF
The CONF? command queries the device's current measurement configuration. This can be either one, two or three comma-separated fields. The number of fields depends on the first fields value, but the second field always denotes the measurement mode's range and resolution, and the third field is the current type (AC or DC).
| Mode | Res. | Cur. | Meaning |
|---|---|---|---|
| V | y | y | Volts |
| 0 | Range 600mV, resolution 0.1mV | ||
| 1 | Range 6V, resolution 1mV | ||
| 2 | Range 60V, resolution 0.01V | ||
| 3 | Range 600V, resolution 0.1V | ||
| MV | y | y | Millivolts |
| 1 | Range 600mV, resolution 0.1mV | ||
| A | y | y | Ampere |
| 0 | Range 6A, resolution 1mA | ||
| 1 | Range 10A, resolution 0.01A | ||
| UA | y | y | Microampere |
| 0 | Range 60μA, resolution 0.01μA | ||
| 1 | Range 600μA, resolution 0.1μA |
STAT
The STAT? command is used to query the current state of the device. The response is a quoted 21-byte string, like this:
"000000000110L00000000"
| Byte | Value | Meaning |
|---|---|---|
| 1 | Max/min mode | |
| 0 | Off | |
| 1 | On | |
| 2 | Relative measurement. The last value returned from FETC? before this mode was enabled denotes the stored reference value. | |
| 0 | Off | |
| 1 | On | |
| 3 | Trig hold-log | |
| 0 | Off | |
| 1 | On | |
| 4 | Auto hold-log | |
| 0 | Off | |
| 1 | On | |
| 5 | LED flashlight | |
| 0 | Off | |
| 1 | On | |
| 6 | LCD backlight | |
| 0 | Off | |
| 1 | On | |
| 7 | Unknown (always 0) | |
| 8 | Temp/aux mode. When on and rotary switch is in position 5 (capacitance), CONF? returns MV,1,DC, but the value returned from FETC? instead denotes the temperature, in the unit (F or C) according to the meter's configuration.
| |
| 0 | Off | |
| 1 | On | |
| 9 | Unknown (always 0) | |
| 10 | Unknown (always 1) | |
| 11 | Auto power-off (APO) | |
| 0 | Off | |
| 1 | On | |
| 12 | Unknown (always 0) | |
| 13 | Unknown (always L) | |
| 14 | Unknown (always 0) | |
| 15 | Unknown (always 0) | |
| 16 | Rotary switch position | |
| 0 | V/Zlow | |
| 1 | Voltage AC | |
| 2 | Voltage DC | |
| 3 | Resistance | |
| 4 | Diode | |
| 5 | Capacitance | |
| 6 | Current | |
| 7 | Microcurrent | |
| 17 | Continuity mode. When enabled, the value returned from FETC? is either NAN (no continuity) or any real value to denote continuity. | |
| 0 | Off | |
| 1 | On | |
| 18 | Unknown (always 0) | |
| 19 | Unknown (always 0, but briefly 1 at startup) | |
| 20 | Unknown (always 0) | |
| 21 | Unknown (always 0) |