TODO

sigrok 0.3

• Add a --start-sampling (TODO: Better name?) option, which just starts sampling with the supplied or default samplerate. Contrary to --time or --samples you don't need to explicitly specify a duration or number of samples here, that's automatically determined by the available memory of the logic analyzer and the selected samplerate.
  • TODO: Similar to --continuous? Merge both?
• Make sure all combinations of --enable-*/--disable-* options works for configure.
  • There may be issue if none of the drivers is enabled, print useful error in that case(?)
• libsigrok.h/libsigrokdecode.h: Only list public API functions.
• Windows port: Implement anykey.c replacement.
  • hex output: Not all lines/columns are of the same length (as they are with real LAs).
  • VCD: All samplenumbers are 0 (instead of the proper samplecount).
  • OLS, gnuplot: Hangs on MinGW for some reasons (not sure if related).
• Finish protocol decoder API design.
• CLI: Eliminate all printing to stdout, only sample data or decoder output should end up there. Error/debug messages should go to stderr always.
• MinGW: Fix Python path decoder issues due to Windows vs. Linux path specification.

sigrok 0.4

• stackable protocol decoder implementation
• modular filter system
  • take arguments in the regular thing:key=value format
  • integrate current probe compression filter
  • resampling module: sample up/down based on factor argument
  • noise filter: filter out pulses shorter than the samplerate's period

Before 1.0

• all output modules should use GString API instead of estimating output size
• VCD input modules
• OLS format input module

Future

• udev:
  • Make udev optional, only build MSO driver if it's available
  • have OLS driver use udev if available, fall back to serial port probing otherwise
  • Find alternative to udev for windows and macos
• Fix/workaround libusb 1.0 Windows port issues:
  • Device renumeration not yet supported (needed for FX2 based LAs)
  • File descriptor / socket based polling not supported in Windows. Workaround (short-term): Use a thread in sigrok.
• Make sure all optional components are really optional in the build system:
  • Only require Python if the users wants protocol decoders, the rest should also build/compile/run fine without Python installed.
• sigrok uses uint64_t as an internal datatype to represent a sample, limiting the number of probes on supported hardware to 64. But high-end logic analyzers can have hundreds of probes. A solution would be to switch to either a roll-our-own byte array type, or use GMP. In any case, the overhead of switching over shouldn't be too bad: the filter code and frontend datafeed callback functions will need to use it, but hardware drivers should have enough with a couple of lightweight wrappers.
• sr_errno:
  • Most functions should return SR_OK or SR_ERR_* (same for SRD_OK etc).
  • Most backend functions return status as an integer, which is SR_OK if all went well, or SR_ERR_* and similar if an error occurred.
  • However there is no way to pass any information back as to what went wrong — and this is important for user-friendliness.
  • Perhaps an error code is not enough; maybe something like sigrok_errno(errorcode, "unsupported device") is better.
• Clean up device-specific globals in hardware drivers, to properly permit multiple devices per driver: asix-sigma, demo (not relevant), link-mso19, openbench-logic-sniffer, saleae-logic, zeroplus-logic-cube
• Python bindings for libsigrok and libsigrokdecode.

Contributors wanted

• Add output for latex package tikz-timing.
• Linux distro packages for non-Debian distros.
• FreeBSD packages/ports.
• Open-source firmware for the FX2 devices

The Cypress FX2-based devices, such as the Saleae Logic and the USBee SX, use only a minimal vendor-provided firmware. The only thing it really does is set the sample rate and turn on the chip's auto-mode. Nevertheless, the vendors provide the firmware as a binary blob, with no source. It would be great if sigrok could ship with an own firmware implementation for these devices. Some links:

• • SDCC, the Small Devices C Compiler, is a compiler specifically suited to small MCUs, and has support for the 8051 core in the FX2.
  • fx2lib is an open-source library for writing firmware on the FX2. It has a number of interesting functions, including implementing custom USB vendor commands.
  • GNU Radio's USRP2 board has an FX2 on it, and GNU Radio has extensive custom firmware for it.