YiXingDianZi MDSO
 | |
| Status | supported |
|---|---|
| Source code | hantek-6xxx |
| Channels | 2 |
| Samplerate | 48MHz |
| Analog bandwidth | 20MHz |
| Vertical resolution | 8bit |
| Triggers | none (SW-only) |
| Input impedance | 1MΩ‖25pF |
| Memory | none |
| Display | none |
| Connectivity | USB |
The YiXingDianZi MDSO (also known as Wosontel MDSO) is a USB-based, 2-channel oscilloscope with an analog bandwidth of 20MS/s and 48MS/s sampling rate.
It comes in very compact plastic case (82x65x23mm) without any branding, USB type B input, 2c BNC inputs, and a red LED.
The YiXingDianZi manufacturer is probably the same as Instrustar (Chinese characters match, lsusb is almost exactly the same).
See YiXingDianZi MDSO/Info for more details (such as lsusb -v output) on the device.
Hardware
- Cypress FX2LP CY7C68013A-56PVXC (USB 2.0 HS controller)
- ADC: Analog Devices AD9288
- EEPROM: Microchip 24LC64I (64K I²C EEPROM)
- 2x ST 74HC4051 (8-Channel analog mux)
- Crystal oscillator 24MHz (crystal)
- 4x 145 MHz FastFET op amp: Analog Devices AD8065 (top markings HRA)
- Unmarked DC/DC converter
- 3.3V LDO: AMS1117-3.3
Cypress FX2 pinout:
| (AD9288 D5B) PD5 | 1- | O | -56 | PD4 (AD9288 D4B) |
| (AD9288 D6B) PD6 | 2- | -55 | PD3 (AD9288 D3B) | |
| (AD9288 D7B) PD7 | 3- | -54 | PD2 (AD9288 D2B) | |
| GND | 4- | -53 | PD1 (AD9288 D1B) | |
| CLKOUT | 5- | -52 | PD0 (AD9288 D0B) | |
| VCC | 6- | -51 | *WAKEUP | |
| GND | 7- | -50 | VCC | |
| RDY0/*SLRD | 8- | -49 | RESET# | |
| RDY1/*SLWR | 9- | -48 | GND | |
| AVCC | 10- | -47 | PA7 | |
| (24MHz crystal) XTALOUT | 11- | -46 | PA6 (CH2 74HC4051 S2) | |
| (24MHz crystal) XTALIN | 12- | -45 | PA5 (CH2 74HC4051 S1) | |
| AGND | 13- | -44 | PA4 (CH2 74HC4051 S0) | |
| AVCC | 14- | -43 | PA3 (CH1 74HC4051 S2) | |
| (USB D+) DPLUS | 15- | -42 | PA2 (CH1 74HC4051 S1) | |
| (USB D-) DMINUS | 16- | -41 | PA1 (CH1 74HC4051 S0) | |
| AGND | 17- | -40 | PA0 | |
| VCC | 18- | -39 | VCC | |
| GND | 19- | -38 | CTL2 | |
| (FX2 CTL0) (AD9288 ENCA/B) *IFCLK | 20- | -37 | CTL1 | |
| RESERVED | 21- | -36 | CTL0 (AD9288 ENCA/B) (FX2 IFCLK) | |
| (EEPROM SCL) SCL | 22- | -35 | GND | |
| (EEPROM SDA) SDA | 23- | -34 | VCC | |
| VCC | 24- | -33 | GND | |
| (AD9288 D0A) PB0 | 25- | -32 | PB7 (AD9288 D7A) | |
| (AD9288 D1A) PB1 | 26- | -31 | PB6 (AD9288 D6A) | |
| (AD9288 D2A) PB2 | 27- | -30 | PB5 (AD9288 D5A) | |
| (AD9288 D3A) PB3 | 28- | -29 | PB4 (AD9288 D4A) |
ST 74HC4051 (upper/lower, CH1/CH2) pinout:
| CH1 (U13) | CH2 (U10) | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
|
|
Input stage gain:
| S2 | S1 | S0 | 74HC4051D Mux | Gain | VDIVs |
|---|---|---|---|---|---|
| 0 | 0 | 0 | Y0 to Z (3.9k) | 5 (4.9 in fact) | 200mV |
| 0 | 0 | 1 | Y1 to Z (1k) | 2 | 500mV |
| 0 | 1 | 0 | Y2 to Z (0) | 1 | 1V |
| 0 | 1 | 1 | Y3 to Z (15k) | 16 | 62.5mV |
Microchip 24LC64I pinout:
| (VCC) A0 | 1- | O | -8 | VCC |
| (GND) A1 | 2- | -7 | WP (GND) | |
| (GND) A2 | 3- | -6 | SCL (FX2 SCL) | |
| VSS | 4- | -5 | SDA (FX2 SDA) |
Analog Devices AD9288 pinout:
| AD9288 pins | Description |
|---|---|
| S1, S2 | S1=VCC, S2=GND. "Normal operation, data align disabled". |
| DFS | Tied to GND. Data format select = "offset binary" (not "twos complement"). |
| AINA, AINB | Analog input channels. |
| D0A-D7A | Connected to FX2 PB0-PB7. |
| D0B-D7B | Connected to FX2 PD0-PD7. |
Firmware
Note: The firmware is flashed into the device permanently.
EEPROM layout
The device has a 8KB I²C EEPROM with the following layout:
c2 47 05 31 21 00 00 04 XX XX XX XX XX XX .. ..
Description:
| Bytes | Description |
|---|---|
| 0 | 0xc2: FX2 "c2 load" mode, i.e. VID/PID/DID are loaded from EEPROM as the firmware. |
| 1-2 | 0x0547: USB vendor ID (VID before firmware renumerate). |
| 3-4 | 0x2131: USB product ID (PID before firmware renumerate). |
| 5-6 | 0x0000: USB device ID (DID before firmware renumerate). |
| 7 | 0x04: FX2 configuration byte (see FX2 TRM for details). |
| 8-1917h | Firmware. |
| 1918h -1fffh | All-0xff. |
Photos
Packaging
Device, top
Inside
PCB, top
PCB, bottom
PCB, USB side
PCB, analog frontend
