Difference between revisions of "Mcupro Logic16 clone"
Jump to navigation
Jump to search
Uwe Hermann (talk | contribs) m |
Uwe Hermann (talk | contribs) m |
||
| Line 3: | Line 3: | ||
| image = [[File:Mcupro_Logic16_overview.png|180px]] | | image = [[File:Mcupro_Logic16_overview.png|180px]] | ||
| name = mcupro Logic16 clone | | name = mcupro Logic16 clone | ||
| status = | | status = supported | ||
| source_code_dir = saleae-logic16 | | source_code_dir = saleae-logic16 | ||
| channels = 3/6/9/16 | | channels = 3/6/9/16 | ||
| Line 28: | Line 28: | ||
* '''I2C EEPROM''': [http://www.atmel.com/Images/doc3256.pdf Atmel 24C02N] | * '''I2C EEPROM''': [http://www.atmel.com/Images/doc3256.pdf Atmel 24C02N] | ||
* '''3.3V voltage regulator''': [http://ams-semitech.com/attachments/File/AMS1117_20120314.pdf Advanced Monolithic Systems AMS1117-3.3] | * '''3.3V voltage regulator''': [http://ams-semitech.com/attachments/File/AMS1117_20120314.pdf Advanced Monolithic Systems AMS1117-3.3] | ||
* '''1. | * '''1.5V voltage regulator''': [http://ams-semitech.com/attachments/File/AMS1117_20120314.pdf Advanced Monolithic Systems AMS1117-1.5] | ||
* '''Crystal:''' 24.000MHz | * '''Crystal:''' 24.000MHz | ||
| Line 52: | Line 52: | ||
[[Category:Device]] | [[Category:Device]] | ||
[[Category:Logic analyzer]] | [[Category:Logic analyzer]] | ||
[[Category: | [[Category:Supported]] | ||
Revision as of 12:04, 19 September 2014
 | |
| Status | supported |
|---|---|
| Source code | saleae-logic16 |
| Channels | 3/6/9/16 |
| Samplerate | 100/50/32/16MHz |
| Samplerate (state) | — |
| Triggers | none (SW-only) |
| Min/max voltage | -0.9V — 6V |
| Threshold voltage | 1.5V (operates with 3.3V logic) |
| Memory | none |
| Compression | yes |
| Website | aliexpress.com |
The mcupro Logic16 clone is a USB-based, 16-channel logic analyzer with 100/50/32/16MHz sampling rate (at 3/6/9/16 enabled channels).
This is a clone of the Saleae Logic16.
See mcupro Logic16 clone/Info for more details (such as lsusb -v output) about the device.
Hardware
- FPGA: Actel A3P125
- USB interface chip: Cypress CY7C68013A
- I2C EEPROM: Atmel 24C02N
- 3.3V voltage regulator: Advanced Monolithic Systems AMS1117-3.3
- 1.5V voltage regulator: Advanced Monolithic Systems AMS1117-1.5
- Crystal: 24.000MHz
Photos
Device, top
Device, bottom
PCB, top
PCB, bottom
Protocol
Firmware
This logic analyzer works with unmodified Saleae software. The Actel FPGA has on-chip flash storage, so it only requires an upload of Cypress FX2LP firmware in order to operate.
The firmware extraction steps are identical to steps for Saleae Logic16, however you only need to have saleae-logic16-fx2.fw installed.