Difference between revisions of "Protocol decoder:Spiflash"
Uwe Hermann (talk | contribs) m |
Uwe Hermann (talk | contribs) m |
||
| Line 13: | Line 13: | ||
}} | }} | ||
The '''mx25lxx05d''' protocol decoder supports the [http://www.macronix.com/ | The '''mx25lxx05d''' protocol decoder supports the [http://www.macronix.com/en-us/Product/Pages/ProductDetail.aspx?PartNo=MX25L1605D Macronix MX25L1605D] / MX25L3205D / MX25L6405D SPI (NOR) flash chip protocol. | ||
== Hardware == | == Hardware == | ||
| Line 81: | Line 81: | ||
== Resources == | == Resources == | ||
* [http://www.macronix.com/ | * [http://www.macronix.com/en-us/Product/Pages/ProductDetail.aspx?PartNo=MX25L1605D Macronix MX25L1605D] ([http://www.macronix.com/Lists/DataSheet/Attachments/1514/MX25L1605D,%203V,%2016Mb,%20v1.5.pdf datasheet]) | ||
[[Category:Protocol decoder]] | [[Category:Protocol decoder]] | ||
[[Category:SPI]] | [[Category:SPI]] | ||
Revision as of 17:30, 23 February 2014
 | |
| Name | Macronix MX25Lxx05D |
|---|---|
| Description | SPI-attached serial EEPROM |
| Status | supported |
| License | GPLv2+ |
| Source code | decoders/mx25lxx05d |
| Input | spi, logic |
| Output | mx25lxx05d |
| Probes | — |
| Optional probes | HOLD#, WP#/ACC |
The mx25lxx05d protocol decoder supports the Macronix MX25L1605D / MX25L3205D / MX25L6405D SPI (NOR) flash chip protocol.
Hardware
Chip pinout
The Macronix MX25Lxx05D chips have the following pinout:
| CS# | 1- | O | -8 | VCC |
| SO | 2- | -7 | HOLD# | |
| WP# | 3- | -6 | SCLK | |
| GND | 4- | -5 | SI |
Macronix MX25L1605D in openbiosprog-spi
The spi/mx25l1605d directory in sigrok-dumps contains a set of example captures of a Macronix MX25L1605D (MX25L1605DPI-12G) SPI flash chip (16Mbit == 2Mbyte; NOR flash) that is probed, being written to, read, or erased.
The logic analyzer used was a ChronoVu LA8 (at 25MHz). It is probing the SPI chip in the openbiosprog-spi Open Hardware USB-based SPI chip programmer. The host software used is flashrom.
Probe setup:
| Probe | MX25L1605D pin |
|---|---|
| 0 (green) | CS# |
| 1 (orange) | SO/SIO1 (a.k.a MISO) |
| 2 (white) | SCLK |
| 3 (red) | SI/SIO0 (a.k.a MOSI) |
| 4 (gray) | WP#/ACC |
| 5 (brown) | HOLD# |
Photos:
openbiosprog-spi with chip
Macronix MX25L1605D
Chip, probed
Protocol
The chip uses the standard SPI protocol and pins (MISO, MOSI, SCLK, CS#), with the additional (optional) HOLD# and WP#/ACC pins.
The host can send a large number of commands to the SPI chip (such as WREN, RDID, READ, SE, CE, PP, and many more). The commands have various length, and usually consist of one command ID byte, optional address bytes, one or more data/payload bytes, and so on (depending on the command).
See the chip datasheet for a detailed protocol/register/command description.