Difference between revisions of "Agilent U1232A"
Uwe Hermann (talk | contribs) m |
Uwe Hermann (talk | contribs) m (Uwe Hermann moved page Agilent U123xA to Agilent U1232A without leaving a redirect) |
(No difference)
| |
Revision as of 11:32, 26 November 2012
 | |
| Status | supported |
|---|---|
| Source code | agilent-dmm |
| Counts | 6000 |
| IEC 61010-1 | CAT III (600V) |
| Connectivity | USB, Bluetooth |
| Measurements | voltage, current, resistance, capacitance, frequency, duty cycle (?), diode, continuity |
| Features | autorange, true-rms, data hold, min/max, rel, bargraph, backlight, LED flashlight, data logging (10 readings), auto-poweroff |
| Website | agilent.com |
The Agilent U1232A is a 6000 counts, CAT III (600V) handheld digital multimeter with USB or Bluetooth connectivity.
Hardware
- Renesas 78K0/LF3 8-bit microcontroller with 60K flash and 2K RAM on board.
Photos
Multimeter:
Device, front
Device, back
PCB, top
White silkscreen (LCD background)
PCB, bottom
PCB detail
Microcontroller
IR-USB cable:
See Device cables#Agilent_U1173A.
IR-Bluetooth interface:
See Device cables#Agilent_U1177A.
Protocol
IDN
Sending the command *IDN? causes the device to return a comma-separated four-field string, compatible with the identical GPIB command. The four fields are vendor name, model name, serial number and version:
Agilent Technologies,U1232A,MY52020136,V1.00
FETC
The FETC? command returns the current measured value, as a floating point ASCII string:
+9.25000000E-03
The value always takes exactly this form. If no valid measurement is available, i.e. the display shows "OL", the transmitted value is +9.90000000E+37.
CONF
The CONF? command queries the device's current measurement configuration. This can be either one, two or three comma-separated fields. The number of fields depends on the first field's value, but the second field always denotes the measurement mode's range and resolution, and the third field is the current type (AC or DC).
| Mode | Res. | Cur. | Meaning |
|---|---|---|---|
| V | y | y | Volts |
| 0 | Range 600mV, resolution 0.1mV | ||
| 1 | Range 6V, resolution 1mV | ||
| 2 | Range 60V, resolution 0.01V | ||
| 3 | Range 600V, resolution 0.1V | ||
| MV | y | y | Millivolts |
| 1 | Range 600mV, resolution 0.1mV | ||
| A | y | y | Ampere |
| 0 | Range 6A, resolution 1mA | ||
| 1 | Range 10A, resolution 0.01A | ||
| UA | y | y | Microampere |
| 0 | Range 60μA, resolution 0.01μA | ||
| 1 | Range 600μA, resolution 0.1μA | ||
| FREQ | y | y | AC frequency |
| 0 | Always shows 0, even when the range is changed manually on the device. This is possibly a firmware bug. | ||
| RES | y | n | Resistance |
| 0 | Range 600Ω, resolution 0.1Ω | ||
| 1 | Range 6kΩ, resolution 0.001kΩ | ||
| 2 | Range 60kΩ, resolution 0.01kΩ | ||
| 3 | Range 600kΩ, resolution 0.1kΩ | ||
| 4 | Range 6MΩ, resolution 0.001MΩ | ||
| 5 | Range 60MΩ, resolution 0.01MΩ | ||
| CAP | y | n | Capacitance |
| 0 | Range 1000nF, resolution 1nF | ||
| 1 | Range 10μF, resolution 0.01μF | ||
| 2 | Range 100μF, resolution 0.1μF | ||
| 3 | Range 1000μF, resolution 1μF | ||
| 4 | Range 10mF, resolution 0.01mF | ||
| DIOD | n | n | Diode |
STAT
The STAT? command is used to query the current state of the device. The response is a quoted 21-byte string, like this:
"000000000110L00000000"
| Byte | Value | Meaning |
|---|---|---|
| 1 | Max/min/avg mode | |
| 0 | Off | |
| 1 | On | |
| 2 | Relative measurement. The last value returned from FETC? before this mode was enabled denotes the stored reference value. | |
| 0 | Off | |
| 1 | On | |
| 3 | Trig hold-log | |
| 0 | Off | |
| 1 | On | |
| 4 | Auto hold-log | |
| 0 | Off | |
| 1 | On | |
| 5 | LED flashlight | |
| 0 | Off | |
| 1 | On | |
| 6 | LCD backlight | |
| 0 | Off | |
| 1 | On | |
| 7 | Smoothing | |
| 0 | Off | |
| 1 | On | |
| 8 | Temp/aux mode. When on and rotary switch is in position 5 (capacitance), CONF? returns MV,1,DC, but the value returned from FETC? instead denotes the temperature, in the unit (F or C) according to the meter's configuration.
| |
| 0 | Off | |
| 1 | On | |
| 9 | Unknown (always 0) | |
| 10 | Beep frequency | |
| 0 | 4.2kHz | |
| 1 | 3.8kHz (default) | |
| 2 | 3.4kHz | |
| 3 | 3.2kHz | |
| 4 | Off | |
| 11 | Auto power-off (APO) | |
| 0 | Off | |
| 1 | On | |
| 12 | Unknown (always 0) | |
| 13 | Unknown (always L) | |
| 14 | Unknown (always 0) | |
| 15 | Unknown (always 0) | |
| 16 | Rotary switch position | |
| 0 | V/Zlow | |
| 1 | Voltage AC | |
| 2 | Voltage DC | |
| 3 | Resistance | |
| 4 | Diode | |
| 5 | Capacitance | |
| 6 | Current | |
| 7 | Microcurrent | |
| 17 | Continuity mode. When enabled, the value returned from FETC? is either NAN (no continuity) or any real value to denote continuity. | |
| 0 | Off | |
| 1 | On | |
| 18 | Unknown (always 0) | |
| 19 | Unknown (always 0, but briefly 1 at startup) | |
| 20 | Unknown (always 0) | |
| 21 | Unknown (always 0) |