Difference between revisions of "V&A VA18B"
Uwe Hermann (talk | contribs) m (→Model overview: PCB silk screen: "VA18B 20070302".) |
Uwe Hermann (talk | contribs) m |
||
| Line 7: | Line 7: | ||
== Model overview == | == Model overview == | ||
It seems there have been at least two different revisions of the multimeter (or at least of the PC-Link cable). The older one used a Sunplus SPCP825 USB-to-serial chip (see [http://www.mikrocontroller.net/topic/160215#2032176 here], [http://multimeter.schewe.com/ here], or also check the drivers from [http://www.elv.de/digital-multimeter-va18b-mit-pc-link.html here]), the newer revisions use a Prolific | It seems there have been at least two different revisions of the multimeter (or at least of the PC-Link cable). The older one used a Sunplus SPCP825 USB-to-serial chip (see [http://www.mikrocontroller.net/topic/160215#2032176 here], [http://multimeter.schewe.com/ here], or also check the drivers from [http://www.elv.de/digital-multimeter-va18b-mit-pc-link.html here]), the newer revisions use a Prolific PL2303HX chip. Both should work fine with sigrok, as long as the respective driver creates a "virtual COM port" / serial port device sigrok can connect to. | ||
{| border="0" style="font-size: smaller" class="alternategrey sortable sigroktable" | {| border="0" style="font-size: smaller" class="alternategrey sortable sigroktable" | ||
| Line 35: | Line 35: | ||
| [http://www.mastech.com.cn/html/en/products-va18b.htm Mastech VA18B] (new) | | [http://www.mastech.com.cn/html/en/products-va18b.htm Mastech VA18B] (new) | ||
| no | | no | ||
| Prolific | | Prolific PL2303HX | ||
| "PC-LINK" | | "PC-LINK" | ||
| Manual: [http://www.mastech.com.cn/down/VA18B.pdf VA18B.pdf]. PCB silk screen: "VA18B 20070302". | | Manual: [http://www.mastech.com.cn/down/VA18B.pdf VA18B.pdf]. PCB silk screen: "VA18B 20070302". | ||
| Line 84: | Line 84: | ||
== Photos == | == Photos == | ||
'''Multimeter:''' | |||
<gallery> | <gallery> | ||
| Line 101: | Line 103: | ||
File:Mastech va18b 7530-1.jpg|<small>7350-1</small> | File:Mastech va18b 7530-1.jpg|<small>7350-1</small> | ||
File:Mastech va18b crystal.jpg|<small>Crystal</small> | File:Mastech va18b crystal.jpg|<small>Crystal</small> | ||
</gallery> | |||
'''USB cable:''' | |||
<gallery> | |||
File:Mastech va18b usb cable.jpg|<small>USB cable</small> | File:Mastech va18b usb cable.jpg|<small>USB cable</small> | ||
File:Mastech va18b usb cable pcb front.jpg|<small>USB cable PCB, front</small> | File:Mastech va18b usb cable pcb front.jpg|<small>USB cable PCB, front</small> | ||
| Line 108: | Line 115: | ||
== Protocol == | == Protocol == | ||
14-byte LCD segments over USB-2-serial (Prolific | 14-byte LCD segments over USB-2-serial (Prolific PL2303HX chip, 2400 baud, 8n1), see various links below. | ||
To enable output to the PC on the multimeter you have to keep the '''Hz/DUTY''' key pressed while powering on the device. However, it will auto-poweroff after roughly 1 hour, even in this mode. To avoid that, press both the '''Hz/DUTY''' and the '''SELECT''' key during power-up (see [http://www.mastech.com.cn/down/VA18B.pdf manual], page 9, section 2.3.1). | To enable output to the PC on the multimeter you have to keep the '''Hz/DUTY''' key pressed while powering on the device. However, it will auto-poweroff after roughly 1 hour, even in this mode. To avoid that, press both the '''Hz/DUTY''' and the '''SELECT''' key during power-up (see [http://www.mastech.com.cn/down/VA18B.pdf manual], page 9, section 2.3.1). | ||
Revision as of 23:37, 30 June 2012
The Mastech VA18B a.k.a. V&A VA18B (V&A is a brand of Mastech) is a CAT II (1000V) handheld digital multimeter with USB connectivity.
See Mastech VA18B/Info for more details (such as lsusb -vvv output) about the device.
Model overview
It seems there have been at least two different revisions of the multimeter (or at least of the PC-Link cable). The older one used a Sunplus SPCP825 USB-to-serial chip (see here, here, or also check the drivers from here), the newer revisions use a Prolific PL2303HX chip. Both should work fine with sigrok, as long as the respective driver creates a "virtual COM port" / serial port device sigrok can connect to.
| Device | Rebranded? | PC interface chip | Vendor software | Comments |
|---|---|---|---|---|
| Mastech VA18B (old) | no | Sunplus SPCP825 | "PC-LINK" | Manual: VA18B.pdf |
| Mastech VA18B (new) | no | Prolific PL2303HX | "PC-LINK" | Manual: VA18B.pdf. PCB silk screen: "VA18B 20070302". |
| Velleman DVM1200 | yes (VA18B) | ? | "PC-LINK" | — |
| Maxwell MX-25328 | yes (VA18B) | ? | "Maxwell Universal Program" | Maxwell wrote their own PC software, apparently (works fine with the VA18B if you select "25328" as device in the software). |
| Peaktech P3375 | likely (VA18B) | ? | ? | Very likely a rebranded Mastech VA18B (1, 2, 3). |
Hardware
Multimeter:
- Main chip: Unknown, it's very likely a bare die under the black blob (see photos).
- Display: ?
- Precision, very low power, CMOS dual opamp:: 27L2C U85T CN58
- ?: 7530-1 1129
- Crystal: 4MHz
- Fuses: 750mA/600V (5x20mm), 10A/600V (6x30mm)
USB cable:
- USB to serial chip: Prolific PL2303HX YR0903A
- Crystal: 12MHz
Photos
Multimeter:
Package, front
Package, back
Package, contents
Device, front
Device, back
Device, open 1
Device, open 2
PCB, front
PCB, front, 1
PCB, front, 2
PCB, front, 3
PCB, back
27L2C
7350-1
Crystal
USB cable:
USB cable
USB cable PCB, front
USB cable PCB, back
Protocol
14-byte LCD segments over USB-2-serial (Prolific PL2303HX chip, 2400 baud, 8n1), see various links below.
To enable output to the PC on the multimeter you have to keep the Hz/DUTY key pressed while powering on the device. However, it will auto-poweroff after roughly 1 hour, even in this mode. To avoid that, press both the Hz/DUTY and the SELECT key during power-up (see manual, page 9, section 2.3.1).
Resources
- Protocol descriptions: [1], [2], [3]
- EEVblog forums: Product review: DMM latest V&A Mastech VA18B