Difference between revisions of "Sysclk SLA5032"
Uwe Hermann (talk | contribs) (Add Firmware section, more URLs.) |
Uwe Hermann (talk | contribs) m (Image captions.) |
||
| Line 48: | Line 48: | ||
<gallery> | <gallery> | ||
File:Sysclk sla5032 device with cable.jpg | File:Sysclk sla5032 device with cable.jpg|<small>Device with cable</small> | ||
File:Sysclk sla5032 device top.jpg | File:Sysclk sla5032 device top.jpg|<small>Device, top</small> | ||
File:Sysclk sla5032 device bottom.jpg | File:Sysclk sla5032 device bottom.jpg|<small>Device, bottom</small> | ||
File:Sysclk sla5032 device usb.jpg | File:Sysclk sla5032 device usb.jpg|<small>Device, USB</small> | ||
File:Sysclk sla5032 device connector.jpg | File:Sysclk sla5032 device connector.jpg|<small>Device, connector</small> | ||
File:Sysclk sla5032 usb cable.jpg | File:Sysclk sla5032 usb cable.jpg|<small>USB cable</small> | ||
File:Sysclk sla5032 probes.jpg | File:Sysclk sla5032 probes.jpg|<small>Probes</small> | ||
File:Sysclk sla5032 pcb top1.jpg | File:Sysclk sla5032 pcb top1.jpg|<small>PCB, top with SODIMM</small> | ||
File:Sysclk sla5032 pcb top2.jpg | File:Sysclk sla5032 pcb top2.jpg|<small>PCB, top</small> | ||
File:Sysclk sla5032 pcb bottom.jpg | File:Sysclk sla5032 pcb bottom.jpg|<small>PCB, bottom</small> | ||
File:Sysclk sla5032 pcb module top.jpg | File:Sysclk sla5032 pcb module top.jpg|<small>SODIMM, top</small> | ||
File:Sysclk sla5032 pcb module bottom.jpg | File:Sysclk sla5032 pcb module bottom.jpg|<small>SODIMM, bottom</small> | ||
File:Sysclk sla5032 mx25l6445e 100mhz crystal.jpg | File:Sysclk sla5032 mx25l6445e 100mhz crystal.jpg|<small>MX25L6445E + crystal</small> | ||
File:Sysclk sla5032 mx25l6445e.jpg | File:Sysclk sla5032 mx25l6445e.jpg|<small>MX25L6445E</small> | ||
File:Sysclk sla5032 fx2.jpg | File:Sysclk sla5032 fx2.jpg|<small>Cypress FX2</small> | ||
File:Sysclk sla5032 atmel 24c256n.jpg | File:Sysclk sla5032 atmel 24c256n.jpg|<small>Atmel 24C256N</small> | ||
File:Sysclk sla5032 atmel 24c02n.jpg | File:Sysclk sla5032 atmel 24c02n.jpg|<small>Atmel 24C02N</small> | ||
File:Sysclk sla5032 atmega8a 24mhz crystal.jpg | File:Sysclk sla5032 atmega8a 24mhz crystal.jpg|<small>Atmel Atmega8A</small> | ||
File:Sysclk sla5032 ams1117 y125.jpg | File:Sysclk sla5032 ams1117 y125.jpg|<small>AMS1117-3.3</small> | ||
File:Sysclk sla5032 z1021ai.jpg | File:Sysclk sla5032 z1021ai.jpg|<small>AOZ1021AI</small> | ||
</gallery> | </gallery> | ||
Revision as of 16:40, 24 April 2019
 | |
| Status | planned |
|---|---|
| Channels | 32 |
| Samplerate | 500MHz |
| Samplerate (state) | — |
| Triggers | low, high, rising, falling |
| Min/max voltage | -50V — 50V |
| Threshold voltage | VIH=1.6V, VIL=1.3V |
| Memory | 2x 1Gbit DDR2 SDRAM |
| Compression | RLE |
| Website | sysclk.taobao.com |
The Sysclk SLA5032 is a USB-based, 32-channel logic analyzer with up to 500MHz sampling rate.
See Sysclk SLA5032/Info for more details (such as lsusb -v output) about the device.
This devices can be switched into one of three different modes (the current mode is indicated by a green LED on the respective mode text):
- 32CH 500M: 500MHz sampling rate, 32 channels, max. 64Mbits storage per channel, support for hardware triggers (sysclk-sla5032 driver).
- Saleae 100M: The device enumerates as a Saleae Logic16, streaming possible like with the Logic16, only software triggers (saleae-logic16 driver).
- Saleae 500M: Similar to the above, but the max. sampling rate is actually 500MHz.
Switching between modes is done via the following mechanism: Plug the device into USB, after roughly half a second unplug it and re-plug it again. A green LED will now indicate that another mode was selected (it'll rotate through all three possible modes).
Hardware
Main board:
- Microcontroller: Atmel Atmega8A (datasheet)
- USB interface chip: Cypress CY7C68013A-56LTXI (FX2LP) (datasheet)
- 32Kbyte I²C EEPROM: Atmel 24C256N (datasheet)
- 256byte I²C EEPROM: Atmel 24C02N (datasheet)
- 8MByte SPI NOR flash: Macronix MX25L6445E (datasheet)
- 3.3V voltage regulator: Advanced Monolithic Systems AMS1117-3.3 (datasheet, older datasheet)
- DC-DC buck regulator: 4x Alpha and Omega AOZ1021AI (datasheet)
- Crystal: 24MHz
SODIMM daughterboard:
- FPGA: Xilinx Spartan XC6SLX16 (datasheet)
- 8MByte SPI NOR flash: Macronix MX25L6445E (datasheet)
- 1Gbit DDR2 SDRAM: 2x Micron MT47H64M16HR-25E:H (markings: "5DHI7 D9LHT") (datasheet)
- Crystal: 100MHz
Photos
Device with cable
Device, top
Device, bottom
Device, USB
Device, connector
USB cable
Probes
PCB, top with SODIMM
PCB, top
PCB, bottom
SODIMM, top
SODIMM, bottom
MX25L6445E + crystal
MX25L6445E
Cypress FX2
Atmel 24C256N
Atmel 24C02N
Atmel Atmega8A
AMS1117-3.3
AOZ1021AI
Firmware
In order to use this device, you need a firmware/bitstream file from the vendor software (from the CD-ROM shipped with the device or from a vendor download of the software). You can e.g. install the Windows vendor software, then get the file C:\Program Files (x86)\SLA5032\bin\top.bit, rename it to sysclk-sla5032.bit and place it in a location where libsigrok will search for firmware (see libsigrok's README.devices file for details).