Difference between revisions of "Mcupro Logic16 clone"
(→Hardware (2014-01-25 variant): added tentative FPGA + IC info) |
|||
| Line 61: | Line 61: | ||
The PCB is marked "Saleae Logic 16 mcupro 2014.1.25". | The PCB is marked "Saleae Logic 16 mcupro 2014.1.25". | ||
* '''FPGA''': Markings ground off | * '''FPGA''': Markings ground off, pinout would indicate a Cyclone EP1C3 (JTAG IDCODE not confirmed yet) | ||
* '''USB interface chip''': Markings ground off | * '''USB interface chip''': Markings sometimes ground off ? CY7C68013A | ||
* '''Crystal (FX2)''': marked "DKF 24.000" | |||
* '''Crystal (FPGA)''': marked "RAK32.00" | |||
* '''FPGA bitstream''': 25P10 1MBit SPI NOR flash, ST Microelectronics (see Micron M25P10 [https://www.micron.com/~/media/documents/products/data-sheet/nor-flash/serial-nor/m25p/m25p10a.pdf datasheet] too) | |||
* '''I²C EEPROM''': Markings ground off | |||
* '''3.3V voltage regulator''': unknown switching regulator (marked "IC5CJ" ?) + 150k/680k resistors pair | |||
* '''1.5V voltage regulator''': unknown switching regulator (marked "IC5CJ" ?) + 160k/240k resistors pair | |||
The bottom two channels are not GND, but SCK (sample clock out) and HCK (half of SCK out). | The bottom two channels are not GND, but SCK (sample clock out) and HCK (half of SCK out). | ||
Revision as of 20:15, 6 April 2016
 | |
| Status | supported |
|---|---|
| Source code | saleae-logic16 |
| Channels | 3/6/9/16 |
| Samplerate | 100/50/32/16MHz |
| Samplerate (state) | — |
| Triggers | none (SW-only) |
| Min/max voltage | -0.9V — 6V |
| Threshold voltage | 1.5V (operates with 3.3V logic) |
| Memory | none |
| Compression | yes |
| Website | aliexpress.com |
The mcupro Logic16 clone is a USB-based, 16-channel logic analyzer with 100/50/32/16MHz sampling rate (at 3/6/9/16 enabled channels).
This is a clone of the Saleae Logic16.
See mcupro Logic16 clone/Info for more details (such as lsusb -v output) about the device.
Hardware (Actel variant)
- FPGA: Actel A3P125
- USB interface chip: Cypress CY7C68013A
- I²C EEPROM: Atmel 24C02N
- 3.3V voltage regulator: Advanced Monolithic Systems AMS1117-3.3
- 1.5V voltage regulator: Advanced Monolithic Systems AMS1117-1.5
- Crystal: 24MHz
Hardware (Cylone variant)
- FPGA: Altera Cyclone EP1C3T100
- USB interface chip: Cypress CY7C68013A
- I²C EEPROM: Atmel 24C02N
- 3.3V voltage regulator: Advanced Monolithic Systems AMS1117-3.3
- 1.5V voltage regulator: Advanced Monolithic Systems AMS1117-1.5
- Crystal (FX2): 24MHz
- Crystal (FPGA): 100MHz
- FPGA bitstream: 25P10 1MBit SPI NOR flash, ST Microelectronics
- Bootstrap controller: STCMCU 15F10, 8051 compatible
Hardware (2015-01-08 variant)
The PCB is marked "Saleae Logic 16 By MCUPro 2015-1-8". Readily identifiable by the irregular PCB traces, and switching power supplies. This comes in a different case, identical to the Noname_XL-LOGIC16-100M.
- FPGA: Markings ground off
- USB interface chip: Cypress CY7C68013A
- I²C EEPROM: Markings ground off
- 3.3V voltage regulator: TD 6810 adjustable version + 150k/680k resistors pair
- 1.5V voltage regulator: TD 6810 adjustable version + 160k/240k resistors pair
- Crystal (FX2): 24MHz
- Crystal (FPGA): Looks like 32MHz?
- FPGA bitstream: 25P10 1MBit SPI NOR flash, ST Microelectronics
- Bootstrap controller: Not required?
Hardware (2014-01-25 variant)
The PCB is marked "Saleae Logic 16 mcupro 2014.1.25".
- FPGA: Markings ground off, pinout would indicate a Cyclone EP1C3 (JTAG IDCODE not confirmed yet)
- USB interface chip: Markings sometimes ground off ? CY7C68013A
- Crystal (FX2): marked "DKF 24.000"
- Crystal (FPGA): marked "RAK32.00"
- FPGA bitstream: 25P10 1MBit SPI NOR flash, ST Microelectronics (see Micron M25P10 datasheet too)
- I²C EEPROM: Markings ground off
- 3.3V voltage regulator: unknown switching regulator (marked "IC5CJ" ?) + 150k/680k resistors pair
- 1.5V voltage regulator: unknown switching regulator (marked "IC5CJ" ?) + 160k/240k resistors pair
The bottom two channels are not GND, but SCK (sample clock out) and HCK (half of SCK out).
Photos (Actel)
Device, top
Device, bottom
PCB, top
PCB, bottom
Photos (Cyclone)
Device, top
Device, bottom
PCB with Altera Cyclone, top
PCB with Altera Cyclone, bottom
PCB, top, 1MBit flash and STCMCU uC
Photos (2015-01-08 variant)
Device, top
PCB, top
PCB, bottom
PCB, 3.3 and 1.5 voltage regulators
PCB, bottom - chip markings intact
Photos (2014-01-25 variant)
Device, top
PCB, top
PCB, bottom
Protocol
Firmware
- Actel variant
- This logic analyzer works with unmodified Saleae software. The Actel FPGA has on-chip flash storage, so it only requires an upload of Cypress FX2LP firmware in order to operate.
- Cyclone variant
- This logic analyzer works with unmodified Saleae software. The PCB contains an SPI flash chip, so it only requires an upload of Cypress FX2LP firmware in order to operate.
- 2015-01-08 variant
- Only requires an upload of Cypress FX2LP firmware to operate. Open-source binaries from gregani work, but must be renamed to saleae-logic16-fx2.fw. It also requires a libsigrok more recent than 2014-08-22 to work (see bug #680).
- 2014-01-25 variant
- Seems to have the bitstream in internal flash, so it only requires an upload of Cypress FX2LP firmware in order to operate. This requires a libsigrok more recent than 2014-08-22 to work (see bug #680).
The firmware extraction steps are identical to steps for Saleae Logic16, however you only need to have saleae-logic16-fx2.fw installed.