Mcupro Logic16 clone

mcupro Logic16 clone

Status	supported
Source code	saleae-logic16
Channels	3/6/9/16
Samplerate	100/50/32/16MHz
Samplerate (state)	—
Triggers	none (SW-only)
Min/max voltage	-0.9V — 6V
Threshold voltage	1.5V (operates with 3.3V logic)
Memory	none
Compression	yes
Website	aliexpress.com

The mcupro Logic16 clone is a USB-based, 16-channel logic analyzer with 100/50/32/16MHz sampling rate (at 3/6/9/16 enabled channels).

This is a clone of the Saleae Logic16.

See mcupro Logic16 clone/Info for more details (such as lsusb -v output) about the device.

Hardware (Actel variant)

• FPGA: Actel A3P125
• USB interface chip: Cypress CY7C68013A
• I²C EEPROM: Atmel 24C02N
• 3.3V voltage regulator: Advanced Monolithic Systems AMS1117-3.3
• 1.5V voltage regulator: Advanced Monolithic Systems AMS1117-1.5
• Crystal: 24MHz

Hardware (Cylone variant)

• FPGA: Altera Cyclone EP1C3T100
• USB interface chip: Cypress CY7C68013A
• I²C EEPROM: Atmel 24C02N
• 3.3V voltage regulator: Advanced Monolithic Systems AMS1117-3.3
• 1.5V voltage regulator: Advanced Monolithic Systems AMS1117-1.5
• Crystal (FX2): 24MHz
• Crystal (FPGA): 100MHz
• FPGA bitstream: 25P10 1MBit SPI NOR flash, ST Microelectronics
• Bootstrap controller: STCMCU 15F10, 8051 compatible

Hardware (2015-01-08 variant)

The PCB is marked "Saleae Logic 16 By MCUPro 2015-1-8". Readily identifiable by the irregular PCB traces, and switching power supplies. This comes in a different case, identical to the Noname_XL-LOGIC16-100M.

• FPGA: Markings ground off
• USB interface chip: Cypress CY7C68013A
• I²C EEPROM: Markings ground off
• 3.3V voltage regulator: TD 6810 adjustable version + 150k/680k resistors pair
• 1.5V voltage regulator: TD 6810 adjustable version + 160k/240k resistors pair
• Crystal (FX2): 24MHz
• Crystal (FPGA): Looks like 32MHz?
• FPGA bitstream: 25P10 1MBit SPI NOR flash, ST Microelectronics
• Bootstrap controller: Not required?

Hardware (2014-01-25 variant)

The PCB is marked "Saleae Logic 16 mcupro 2014.1.25".

• FPGA: Markings ground off
• USB interface chip: Markings ground off

The bottom two channels are not GND, but SCK (sample clock out) and HCK (half of SCK out).

Photos (Actel)

• 

  Device, top

• 

  Device, bottom

• 

  PCB, top

• 

  PCB, bottom

Photos (Cyclone)

• 

  Device, top

• 

  Device, bottom

• 

  PCB with Altera Cyclone, top

• 

  PCB with Altera Cyclone, bottom

• 

  PCB, top, 1MBit flash and STCMCU uC

Photos (2015-01-08 variant)

• 

  Device, top

• 

  PCB, top

• 

  PCB, bottom

• 

  PCB, 3.3 and 1.5 voltage regulators

• 

  PCB, bottom - chip markings intact

Photos (2014-01-25 variant)

• 

  Device, top

• 

  PCB, top

• 

  PCB, bottom

Protocol

See Saleae_Logic16#Protocol.

Firmware

Actel variant

This logic analyzer works with unmodified Saleae software. The Actel FPGA has on-chip flash storage, so it only requires an upload of Cypress FX2LP firmware in order to operate.

Cyclone variant

This logic analyzer works with unmodified Saleae software. The PCB contains an SPI flash chip, so it only requires an upload of Cypress FX2LP firmware in order to operate.

2015-01-08 variant

Only requires an upload of Cypress FX2LP firmware to operate. Open-source binaries from gregani work, but must be renamed to saleae-logic16-fx2.fw.

2014-01-25 variant

Seems to have the bitstream in internal flash, so it only requires an upload of Cypress FX2LP firmware in order to operate. This requires a libsigrok more recent than 2014-08-22 to work (see bug #680).

The firmware extraction steps are identical to steps for Saleae Logic16, however you only need to have saleae-logic16-fx2.fw installed.