Difference between revisions of "Mcupro Logic16 clone"
| Line 59: | Line 59: | ||
* '''FPGA''': Markings ground off | * '''FPGA''': Markings ground off | ||
* '''USB interface chip''': Markings ground off | * '''USB interface chip''': Markings ground off | ||
* MISC, bottom two channels are not GND, buy SCK(Sample Clock out) and HCK (Half of SCK out). | |||
== Photos (Actel) == | == Photos (Actel) == | ||
Revision as of 14:34, 28 September 2015
 | |
| Status | supported |
|---|---|
| Source code | saleae-logic16 |
| Channels | 3/6/9/16 |
| Samplerate | 100/50/32/16MHz |
| Samplerate (state) | — |
| Triggers | none (SW-only) |
| Min/max voltage | -0.9V — 6V |
| Threshold voltage | 1.5V (operates with 3.3V logic) |
| Memory | none |
| Compression | yes |
| Website | aliexpress.com |
The mcupro Logic16 clone is a USB-based, 16-channel logic analyzer with 100/50/32/16MHz sampling rate (at 3/6/9/16 enabled channels).
This is a clone of the Saleae Logic16.
See mcupro Logic16 clone/Info for more details (such as lsusb -v output) about the device.
Hardware (Actel variant)
- FPGA: Actel A3P125
- USB interface chip: Cypress CY7C68013A
- I2C EEPROM: Atmel 24C02N
- 3.3V voltage regulator: Advanced Monolithic Systems AMS1117-3.3
- 1.5V voltage regulator: Advanced Monolithic Systems AMS1117-1.5
- Crystal: 24.000MHz
Hardware (Cylone variant)
- FPGA: Altera Cyclone EP1C3T100
- USB interface chip: Cypress CY7C68013A
- I2C EEPROM: Atmel 24C02N
- 3.3V voltage regulator: Advanced Monolithic Systems AMS1117-3.3
- 1.5V voltage regulator: Advanced Monolithic Systems AMS1117-1.5
- Crystal (FX2): 24.000MHz
- Crystal (FPGA): 100.000MHz
- FPGA Bitstream 25P10 1MBit SPI NOR flash, ST Microelectronics
- Bootstrap Controller STCMCU 15F10, 8051 compatible
Hardware (2015-01-08 variant)
PCB Marked "Saleae Logic 16 By MCUPro 2015-1-8" Readily identifiable by the irregular pcb traces, and switching power supplies This comes in a different case, identical to the Noname_XL-LOGIC16-100M.
- FPGA: Markings ground off
- USB interface chip: Markings ground off, but presumably a Cypress FX2 like all others. Cypress CY7C68013A
- I2C EEPROM: Markings ground off
- 3.3V voltage regulator: Unrecognized switcher in sot23-5 (Seems to be 3.8V?!)
- 1.5V voltage regulator: Unrecognised switcher in sot23-5
- Crystal (FX2): 24.000MHz
- Crystal (FPGA): Looks like 32Mhz?
- FPGA Bitstream 25P10 1MBit SPI NOR flash, ST Microelectronics
- Bootstrap Controller Not required?
Hardware (2014-01-25 variant)
PCB Marked "Saleae Logic 16 mcupro 2014.1.25"
- FPGA: Markings ground off
- USB interface chip: Markings ground off
- MISC, bottom two channels are not GND, buy SCK(Sample Clock out) and HCK (Half of SCK out).
Photos (Actel)
Device, top
Device, bottom
PCB, top
PCB, bottom
Photos (Cyclone)
Device, top
Device, bottom
PCB with Altera Cyclone, top
PCB with Altera Cyclone, bottom
PCB, top, 1MBit flash and STCMCU uC
Photos (2015-01-08 variant)
Device, top
PCB, top
PCB, bottom
Photos (2014-01-25 variant)
PCB, top
PCB, bottom
Protocol
Firmware
- Actel variant
- This logic analyzer works with unmodified Saleae software. The Actel FPGA has on-chip flash storage, so it only requires an upload of Cypress FX2LP firmware in order to operate.
- Cyclone variant
- This logic analyzer works with unmodified Saleae software. The PCB contains a serial flash chip, so it only requires an upload of Cypress FX2LP firmware in order to operate.
- 2015-1-8 variant
- Only requires an upload of Cypress FX2LP firmware to operate. Opensource binaries from [1] work, but must be renamed to saleae-logic16-fx2.fw
The firmware extraction steps are identical to steps for Saleae Logic16, however you only need to have saleae-logic16-fx2.fw installed.