Difference between revisions of "Saleae Logic16"
Uwe Hermann (talk | contribs) m (Infobox.) |
|||
| Line 1: | Line 1: | ||
[[File:Saleae Logic16.jpg| | {{Infobox logic analyzer | ||
| image = [[File:Saleae Logic16.jpg|180px]] | |||
| name = Saleae Logic16 | |||
| status = planned | |||
| source_code_dir = | |||
| channels = 2/4/8/16 | |||
| samplerate = 100/50/25/12.5MHz | |||
| samplerate_state = — | |||
| triggers = none (SW-only) | |||
| voltages = -0.9V — 6V | |||
| threshold = configurable:<br />for 1.8V to 3.6V systems: VIH=1.4V, VIL=0.7V<br />for 5V systems: VIH=3.6V, VIL=1.4V | |||
| memory = none | |||
| compression = yes | |||
| website = [http://www.saleae.com/logic16/ saleae.com] | |||
}} | |||
The | The '''Saleae Logic16''' is a USB-based, 16-channel logic analyzer with 100/50/25/12.5MHz sampling rate (at 2/4/8/16 enabled channels). | ||
The case requires a '''Torx T5''' screwdriver to open. | The case requires a '''Torx T5''' screwdriver to open. | ||
Revision as of 10:57, 24 July 2013
 | |
| Status | planned |
|---|---|
| Channels | 2/4/8/16 |
| Samplerate | 100/50/25/12.5MHz |
| Samplerate (state) | — |
| Triggers | none (SW-only) |
| Min/max voltage | -0.9V — 6V |
| Threshold voltage |
configurable: for 1.8V to 3.6V systems: VIH=1.4V, VIL=0.7V for 5V systems: VIH=3.6V, VIL=1.4V |
| Memory | none |
| Compression | yes |
| Website | saleae.com |
The Saleae Logic16 is a USB-based, 16-channel logic analyzer with 100/50/25/12.5MHz sampling rate (at 2/4/8/16 enabled channels).
The case requires a Torx T5 screwdriver to open.
See Saleae Logic16/Info for more details (such as lsusb -vvv output) about the device.
See Saleae Logic for the predecessor product of the Saleae Logic16.
Hardware
- Xilinx XC3S200A 200K gate FPGA
- Cypress CY7C68013A-56PVXC (FX2LP) USB interface chip
Photos
Device, front
Device, bottom
PCB, top
PCB, bottom
Firmware
The firmware for the FX2LP is embedded in the vendor application as a set of Intel HEX lines. Each line is uploaded individually with a separate control transfer. The firmware currently occupies the address range [0x0000-0x145d], but is uploaded out of order. TODO: Make a tool to extract the firmware from the application binary.
See Saleae Logic16/Firmware for more details on the vendor firmware.
Protocol
Sample format:
The samples (as received via USB) for the enabled probes (3, 6, 9, or 16) are organized as follows:
0xLL 0xLL 0xMM 0xMM 0xNN 0xNN 0xPP 0xPP 0xQQ 0xQQ 0xRR 0xRR ...
In the above example, 3 probes are enabled. For each probe there are 2 bytes / 16 bits (e.g. 0xLL 0xLL for probe 0), then the next probe's data is received (0xMM 0xMM for probe 1), then 0xNN 0xNN for probe 2. When 2 bytes have been received for all enabled probes, the process restarts with probe 0 again.
The 16 bits of data per probe seem to contain the pin state of the respective probe (1: high, 0: low) at 16 different sampling points/times (which ones depends on the samplerate).
Configuration:
Endpoint 1 is used for configuration of the analyzer. Two kinds of transfers are used; a 3 byte out transfer starting with 0x55 followed by a 1 byte in transfer, and a 4 byte out transfer starting with 0x5a. It's quite plausible that these provide raw read/write access to memory locations.
| Channel number configuration | |
|---|---|
| 3 channels | 0x5a 0x32 0xf4 0x38 0x5a 0x32 0xef 0x1b |
| 6 channels | 0x5a 0x32 0xf4 0xc0 0x5a 0x32 0xef 0x1b |
| 9 channels | 0x5a 0x32 0xf4 0x80 0x5a 0x32 0xef 0xc8 |
| Sampling frequency | |
|---|---|
| 500 kHz | 0x5a 0x32 0x4c 0x61 0x5a 0x32 0x82 0xb0 |
| 8 MHz | 0x5a 0x32 0x4c 0x5e 0x5a 0x32 0x82 0x0c |