Rigol DG800 Series

Rigol DG800 Series

Status	in progress
Source code	rigol-dg
Frequency (sine)	10-35MHz
Frequency (square)	5-10MHz
Frequency (other)	5-10MHz (pulse), 200-1000KHz (ramp)
Frequency (user)	5-10MHz
Waveforms	sine, square, ramp, pulse, harmonic, noise, arbitrary waveform
Waveform memory	2 Mpts (8 Mpts option)
Modulation	AM, FM, PM, DSB-AM, FSK, ASK, PWM
Connectivity	USBTMC
Website	rigolna.com

Rigol DG800 Series Arbitrary Waveform Generators are 1-2 channel, 10-36MHz high-resolution (16bit) signal generators with up to 8 Mpts waveform memory.

These units appear to me using same hardware (just different color chassis) and firmware as Rigol DG900 Series signal generators.

Devices

Hardware on all these models is identical, only difference is in software/firmware.

Model	Channels	Max Frequency (Sine)	Max Frequency (Square)	Arbitrary Waveform Length	Frequency Counter
DG811	1	10 MHz	5 MHz	2 Mpts	Y
DG812	2	10 MHz	5 MHz	2 Mpts	Y
DG821	1	25 MHz	10 MHz	2 Mpts	Y
DG822	2	25 MHz	10 MHz	2 Mpts	Y
DG831	1	35 MHz	10 MHz	2 Mpts	Y
DG832	2	35 MHz	10 MHz	2 Mpts	Y

• ) Waveform memory can be upgraded to 8 Mbpts via software license.

Hardware

Digital:

TODO

Analog:

TODO

Photos

• 

  Front Panel

Protocol

TODO

Example use

Depending on your type of connection you have to can either use the USBTMC connection parameter or the TCP/IP connection parameter. Examples:

 -d rigol-dg

(usually no parameters are needed when connecting via USB)

When connecting over TCP/IP need to specify ip address and port:

 -d rigol-dg:conn=tcp-raw/192.168.42.42/5555

Check the capabilities of the meter's driver, and current state of settings:

 $ sigrok-cli -d rigol-dg --show

Check the capabilities specific to a channel (1 or 2):

 $ sigrok-cli -d rigol-dg -g 1 --show

Enable or disable channel output (first channel):

 $ sigrok-cli -d rigol-dg -g 1 --set --config enabled=true
 $ sigrok-cli -d rigol-dg -g 1 --set --config enabled=false

Get or set the waveform function (second channel):

 $ sigrok-cli -d rigol-dg -g 2 --get pattern
 $ sigrok-cli -d rigol-dg -g 2 --set --config pattern=square

Get or set the output signal frequency:

 $ sigrok-cli -d rigol-dg -g 1 --get output_frequency
 $ sigrok-cli -d rigol-dg -g 1 --set --config output_frequency=20000

Get or set the output signal amplitude:

 $ sigrok-cli -d rigol-dg -g 1 --get amplitude
 $ sigrok-cli -d rigol-dg -g 1 --set --config amplitude=3.3

Get or set the output signal offset:

 $ sigrok-cli -d rigol-dg -g 1 --get offset
 $ sigrok-cli -d rigol-dg -g 1 --set --config offset=1.0

Get or set the output signal phase:

 $ sigrok-cli -d rigol-dg -g 1 --get phase
 $ sigrok-cli -d rigol-dg -g 1 --set --config phase=90.0

Get or set the output signal duty cycle:

 $ sigrok-cli -d rigol-dg -g 1 --get output_duty_cycle
 $ sigrok-cli -d rigol-dg -g 1 --set --config output_duty_cycle=25.0

Acquire measurement data (frequency counter output):

 $ sigrok-cli -d rigol-dg --continuous
 $ sigrok-cli -d rigol-dg --time 10s
 $ sigrok-cli -d rigol-dg --samples 10

Resources

• DG800 Datasheet
• DG800 User's Guide
• DG800 Programming Guide