Difference between revisions of "Sysclk SLA5032"
Jump to navigation
Jump to search
Uwe Hermann (talk | contribs) (Cosmetics, AliExpress URL.) |
Uwe Hermann (talk | contribs) (Document modes and mode switching.) |
||
| Line 7: | Line 7: | ||
| samplerate = 500MHz | | samplerate = 500MHz | ||
| samplerate_state = — | | samplerate_state = — | ||
| triggers = | | triggers = low, high, rising, falling | ||
| input_impedance = 200kΩ‖15pF | | input_impedance = 200kΩ‖15pF | ||
| voltages = -50V — 50V | | voltages = -50V — 50V | ||
| Line 19: | Line 19: | ||
See [[Sysclk SLA5032/Info]] for more details (such as '''lsusb -v''' output) about the device. | See [[Sysclk SLA5032/Info]] for more details (such as '''lsusb -v''' output) about the device. | ||
This devices can be switched into one of three different modes (the current mode is indicated by a green LED on the respective mode text): | |||
* '''32CH 500M''': 500MHz sampling rate, 32 channels, max. 64Mbits storage per channel, support for hardware triggers ('''sysclk-sla5032''' driver). | |||
* '''Saleae 100M''': The device enumerates as a [[Saleae Logic16]], streaming possible like with the Logic16, only software triggers ('''saleae-logic16''' driver). | |||
* '''Saleae 500M''': Similar to the above, but the max. sampling rate is actually 500MHz. | |||
Switching between modes is done via the following mechanism: Plug the device into USB, after roughly half a second unplug it and re-plug it again. A green LED will now indicate that another mode was selected (it'll rotate through all three possible modes). | |||
== Hardware == | == Hardware == | ||
Revision as of 16:11, 24 April 2019
 | |
| Status | planned |
|---|---|
| Channels | 32 |
| Samplerate | 500MHz |
| Samplerate (state) | — |
| Triggers | low, high, rising, falling |
| Min/max voltage | -50V — 50V |
| Threshold voltage | VIH=1.6V, VIL=1.3V |
| Memory | 2x 1Gbit DDR2 SDRAM |
| Compression | RLE |
| Website | sysclk.taobao.com |
The Sysclk SLA5032 is a USB-based, 32-channel logic analyzer with up to 500MHz sampling rate.
See Sysclk SLA5032/Info for more details (such as lsusb -v output) about the device.
This devices can be switched into one of three different modes (the current mode is indicated by a green LED on the respective mode text):
- 32CH 500M: 500MHz sampling rate, 32 channels, max. 64Mbits storage per channel, support for hardware triggers (sysclk-sla5032 driver).
- Saleae 100M: The device enumerates as a Saleae Logic16, streaming possible like with the Logic16, only software triggers (saleae-logic16 driver).
- Saleae 500M: Similar to the above, but the max. sampling rate is actually 500MHz.
Switching between modes is done via the following mechanism: Plug the device into USB, after roughly half a second unplug it and re-plug it again. A green LED will now indicate that another mode was selected (it'll rotate through all three possible modes).
Hardware
Main board:
- Microcontroller: Atmel Atmega8A (datasheet)
- USB interface chip: Cypress CY7C68013A-56LTXI (FX2LP) (datasheet)
- 32Kbyte I²C EEPROM: Atmel 24C256N (datasheet)
- 256byte I²C EEPROM: Atmel 24C02N (datasheet)
- 8MByte SPI NOR flash: Macronix MX25L6445E (datasheet)
- 3.3V voltage regulator: Advanced Monolithic Systems AMS1117-3.3 (datasheet, older datasheet)
- DC-DC buck regulator: 4x Alpha and Omega AOZ1021AI (datasheet)
- Crystal: 24MHz
SODIMM daughterboard:
- FPGA: Xilinx Spartan XC6SLX16 (datasheet)
- 8MByte SPI NOR flash: Macronix MX25L6445E (datasheet)
- 1Gbit DDR2 SDRAM: 2x Micron MT47H64M16HR-25E:H (markings: "5DHI7 D9LHT") (datasheet)
- Crystal: 100MHz
