Difference between revisions of "ARMFLY AX-Pro"
(→Hardware: +ADC, op amps) |
Uwe Hermann (talk | contribs) |
||
| Line 4: | Line 4: | ||
| status = supported | | status = supported | ||
| source_code_dir = fx2lafw | | source_code_dir = fx2lafw | ||
| channels = 8 | | channels = 8 + 1 | ||
| samplerate = 24MHz | | samplerate = 8ch @ 24MHz, 8+1ch @ 12MHz | ||
| samplerate_state = — | | samplerate_state = — | ||
| triggers = none (SW-only) | | triggers = none (SW-only) | ||
| voltages = max | | voltages = Digital: 0V — +5V<br/>Analog: ±10V (±20V max) | ||
| threshold = Fixed: | | threshold = Fixed: V<sub>IH</sub>=1.4V, V<sub>IL</sub>=0.8V | ||
| memory = none | | memory = none | ||
| compression = none | | compression = none | ||
| Line 15: | Line 15: | ||
}} | }} | ||
The '''ARMFLY AX-Pro''' is a USB-based, 8-channel logic analyzer with up to 24MHz sampling rate, | The '''ARMFLY AX-Pro''' is a USB-based, 8-channel logic analyzer with up to 24MHz sampling rate, with 1 additional analog channel (theoretically 2, but only one of them can be used at a time; 3MHz analog bandwidth). | ||
It is a clone of the [[CWAV USBee AX-Pro]]. There is an "[http://item.taobao.com/item.htm?id=12503749579 RS232 RS485 RS422 CAN converter]" add-on board which also has a BNC connector for analog support. | It is a clone of the [[CWAV USBee AX-Pro]]. There is an "[http://item.taobao.com/item.htm?id=12503749579 RS232 RS485 RS422 CAN converter]" add-on board which also has a BNC connector for analog support. | ||
| Line 21: | Line 21: | ||
In sigrok, we use the open-source [[fx2lafw]] firmware for this logic analyzer. | In sigrok, we use the open-source [[fx2lafw]] firmware for this logic analyzer. | ||
'''Note''': | '''Note''': [[fx2lafw]] currently doesn't support switching between the two possible analog channels, ACH1 will be used unconditionally. | ||
See [[ARMFLY AX-Pro/Info]] for some more details (such as '''lsusb - | See [[ARMFLY AX-Pro/Info]] for some more details (such as '''lsusb -v''' output) on the device. | ||
== Hardware == | == Hardware == | ||
Revision as of 23:01, 17 September 2017
 | |
| Status | supported |
|---|---|
| Source code | fx2lafw |
| Channels | 8 + 1 |
| Samplerate | 8ch @ 24MHz, 8+1ch @ 12MHz |
| Samplerate (state) | — |
| Triggers | none (SW-only) |
| Min/max voltage |
Digital: 0V — +5V Analog: ±10V (±20V max) |
| Threshold voltage | Fixed: VIH=1.4V, VIL=0.8V |
| Memory | none |
| Compression | none |
| Website | armfly.com |
The ARMFLY AX-Pro is a USB-based, 8-channel logic analyzer with up to 24MHz sampling rate, with 1 additional analog channel (theoretically 2, but only one of them can be used at a time; 3MHz analog bandwidth).
It is a clone of the CWAV USBee AX-Pro. There is an "RS232 RS485 RS422 CAN converter" add-on board which also has a BNC connector for analog support.
In sigrok, we use the open-source fx2lafw firmware for this logic analyzer.
Note: fx2lafw currently doesn't support switching between the two possible analog channels, ACH1 will be used unconditionally.
See ARMFLY AX-Pro/Info for some more details (such as lsusb -v output) on the device.
Hardware
- Main chip: Cypress CY7C68013A-56LTXC (FX2LP)
- I2C EEPROM: Atmel ATML920 24C02N SU27 D
- Low-dropout voltage regulator: Advanced Monolithic Systems AMS1117-3.3
- Crystal: 24MHz
- ADC: Texas Instrument TLC5510IPW, 8-Bit, 20 MS/s ADC Single Channel
- OpAmp: Texas Instrument LMV358 Dual Low-Voltage Rail-to-Rail Output Operational Amplifier
- OpAmp: Analog Devices AD8065 (SMD marking "HRA")
- Multiplexor: (I do not see it. Is it U5?)
- ...
Photos
AX-Pro
Cables
PCB, front
Protocol
Since we use the open-source fx2lafw firmware for this device, we don't need to know the protocol.