Difference between revisions of "XZL Studio AX"
Jump to navigation
Jump to search
Uwe Hermann (talk | contribs) m |
m |
||
| (4 intermediate revisions by 2 users not shown) | |||
| Line 5: | Line 5: | ||
| status = supported | | status = supported | ||
| source_code_dir = fx2lafw | | source_code_dir = fx2lafw | ||
| channels = 8 | | channels = 8 + 1 | ||
| samplerate = 24MHz | | samplerate = 8ch @ 24MHz, 8+1ch @ 12MHz | ||
| samplerate_state = — | | samplerate_state = — | ||
| triggers = 1 independent trigger + (SW-probe 0,1) | | triggers = 1 independent trigger + (SW-probe 0,1) | ||
| Line 13: | Line 13: | ||
| memory = none | | memory = none | ||
| compression = none | | compression = none | ||
| price = $20 - 35 | |||
| website = [http://www.hotmcu.com/xzl-ax-oscilloscope-and-logic-analyzer-ax-pro-logic-analyzer-p-14.html?cPath=3_26 hotmcu.com] | | website = [http://www.hotmcu.com/xzl-ax-oscilloscope-and-logic-analyzer-ax-pro-logic-analyzer-p-14.html?cPath=3_26 hotmcu.com] | ||
}} | }} | ||
The '''XZL_Studio AX''' is a USB-based, 8-channel logic analyzer with up to 24MHz sampling rate, | The '''XZL_Studio AX''' is a USB-based, 8-channel logic analyzer with up to 24MHz sampling rate, with 1 additional analog channel (theoretically 2, but only one of them can be used at a time; 3MHz analog bandwidth). | ||
It is a clone of the [[CWAV USBee AX-Pro]]. | It is a clone of the [[CWAV USBee AX-Pro]]. | ||
| Line 22: | Line 23: | ||
In sigrok, we use the open-source [[fx2lafw]] firmware for this logic analyzer. | In sigrok, we use the open-source [[fx2lafw]] firmware for this logic analyzer. | ||
'''Note''': | '''Note''': [[fx2lafw]] currently doesn't support switching between the two possible analog channels, 1ACH (TODO: not verified on hardware) will be used unconditionally. | ||
See [[XZL_Studio AX/Info]] for some more details (such as '''lsusb -v''' output) on the device. | See [[XZL_Studio AX/Info]] for some more details (such as '''lsusb -v''' output) on the device. | ||
| Line 28: | Line 29: | ||
== Hardware == | == Hardware == | ||
* '''Main chip''': Cypress CY7C68013A-56LTXC (FX2LP) | * '''Main chip''': Cypress CY7C68013A-56LTXC (FX2LP), U6 | ||
* '''ADC''': 1x Texas Instruments TLC5510I (SO 24pin package) | * '''ADC''': 1x Texas Instruments TLC5510I (SO 24pin package), 8-Bit, 20 MSPS ADC, Single Channel, U10, outputs D1-D8 connected to PD0-PD7, OE# grounded, CLOCK from CTL2 on U6 | ||
* '''I2C EEPROM''': Atmel 24C02C | * '''I2C EEPROM''': Atmel 24C02C | ||
* '''Low-dropout voltage regulator''': Advanced Monolithic Systems AMS1117-3.3 | * '''Low-dropout voltage regulator''': Advanced Monolithic Systems AMS1117-3.3 | ||
* '''Crystal''': 24MHz | * '''Crystal''': 24MHz | ||
* '''Multiplexer''': HCF4051 - Single 8-Channel Analog Multiplexer/Demultiplexer, U12, channel selectors B and C grounded, selector A controlled by PA0 on U6 | |||
* '''Op Amp''': LM358 - Single Supply Dual Operational Amplifiers, U15 | |||
* ... | * ... | ||
| Line 53: | Line 56: | ||
== Resources == | == Resources == | ||
* [[EE Electronics ESLA201A]] - the same circuit (from firmware's point of view). PCB has been copied and altered, same silkscreen labels. No electrolytic caps, no resistive trimmers, larger screw-hole-keepouts, no cap on pin 13 at U10, no U13 (second MAX1044/ICL7660). Has extra button inside the box! | |||
[[Category:Device]] | [[Category:Device]] | ||
Latest revision as of 15:00, 30 June 2019
 | |
| Status | supported |
|---|---|
| Source code | fx2lafw |
| Channels | 8 + 1 |
| Samplerate | 8ch @ 24MHz, 8+1ch @ 12MHz |
| Samplerate (state) | — |
| Triggers | 1 independent trigger + (SW-probe 0,1) |
| Min/max voltage |
Digital: max. 5.5V Analog: -10V — +10V |
| Threshold voltage | Digital: Fixed: VIH=1.4V, VIL=0.8V |
| Memory | none |
| Compression | none |
| Price range | $20 - 35 |
| Website | hotmcu.com |
The XZL_Studio AX is a USB-based, 8-channel logic analyzer with up to 24MHz sampling rate, with 1 additional analog channel (theoretically 2, but only one of them can be used at a time; 3MHz analog bandwidth).
It is a clone of the CWAV USBee AX-Pro.
In sigrok, we use the open-source fx2lafw firmware for this logic analyzer.
Note: fx2lafw currently doesn't support switching between the two possible analog channels, 1ACH (TODO: not verified on hardware) will be used unconditionally.
See XZL_Studio AX/Info for some more details (such as lsusb -v output) on the device.
Hardware
- Main chip: Cypress CY7C68013A-56LTXC (FX2LP), U6
- ADC: 1x Texas Instruments TLC5510I (SO 24pin package), 8-Bit, 20 MSPS ADC, Single Channel, U10, outputs D1-D8 connected to PD0-PD7, OE# grounded, CLOCK from CTL2 on U6
- I2C EEPROM: Atmel 24C02C
- Low-dropout voltage regulator: Advanced Monolithic Systems AMS1117-3.3
- Crystal: 24MHz
- Multiplexer: HCF4051 - Single 8-Channel Analog Multiplexer/Demultiplexer, U12, channel selectors B and C grounded, selector A controlled by PA0 on U6
- Op Amp: LM358 - Single Supply Dual Operational Amplifiers, U15
- ...
Photos
Device, front
Probe port
USB port
Device, back
PCB, top
PCB, bottom
Probe clips
Protocol
Since we use the open-source fx2lafw firmware for this device, we don't need to know the protocol.
Resources
- EE Electronics ESLA201A - the same circuit (from firmware's point of view). PCB has been copied and altered, same silkscreen labels. No electrolytic caps, no resistive trimmers, larger screw-hole-keepouts, no cap on pin 13 at U10, no U13 (second MAX1044/ICL7660). Has extra button inside the box!