Difference between revisions of "Saleae Logic"
Uwe Hermann (talk | contribs) m (→Protocol) |
Uwe Hermann (talk | contribs) m (Voltages, thresholds.) |
||
| (One intermediate revision by the same user not shown) | |||
| Line 8: | Line 8: | ||
| samplerate_state = — | | samplerate_state = — | ||
| triggers = none (SW-only) | | triggers = none (SW-only) | ||
| voltages = | | voltages = -0.5V — 5.25V | ||
| threshold = Fixed: VIH=2.0V—5.25V, VIL=-0.5V—0.8V | |||
| memory = none | | memory = none | ||
| compression = none | | compression = none | ||
| Line 14: | Line 15: | ||
}} | }} | ||
The '''Saleae Logic''' is a | The '''Saleae Logic''' is a USB-based, 8-channel logic analyzer with up to 24MHz sampling rate. | ||
The unit itself is very small, and has a USB 2.0 port connecting it to a PC (and powering the unit) and a connector for the 8 + 1 probe set. It is built around a Cypress EZ-USB FX2LP microcontroller — an 8051-compatible chip with built-in USB 2.0 controller. It can sample 8 channels up to 24MHz | The unit itself is very small, and has a USB 2.0 port connecting it to a PC (and powering the unit) and a connector for the 8 + 1 probe set. It is built around a Cypress EZ-USB FX2LP microcontroller — an 8051-compatible chip with built-in USB 2.0 controller. It can sample 8 channels up to 24MHz. | ||
In sigrok, we use the open-source [[fx2lafw]] firmware for this logic analyzer. | |||
See [[Saleae Logic/Info]] for more details (such as '''lsusb -vvv''' output) about the device. | See [[Saleae Logic/Info]] for more details (such as '''lsusb -vvv''' output) about the device. | ||
| Line 33: | Line 32: | ||
* '''I2C EEPROM''': Microchip 24LC00 | * '''I2C EEPROM''': Microchip 24LC00 | ||
* '''Crystal''': 24MHz | * '''Crystal''': 24MHz | ||
The case has four '''Torx T2''' screws you need to remove in order to be able to open it. | |||
== Photos == | == Photos == | ||
Latest revision as of 12:07, 28 July 2013
 | |
| Status | supported |
|---|---|
| Source code | fx2lafw |
| Channels | 8 |
| Samplerate | 24MHz |
| Samplerate (state) | — |
| Triggers | none (SW-only) |
| Min/max voltage | -0.5V — 5.25V |
| Threshold voltage | Fixed: VIH=2.0V—5.25V, VIL=-0.5V—0.8V |
| Memory | none |
| Compression | none |
| Website | saleae.com |
The Saleae Logic is a USB-based, 8-channel logic analyzer with up to 24MHz sampling rate.
The unit itself is very small, and has a USB 2.0 port connecting it to a PC (and powering the unit) and a connector for the 8 + 1 probe set. It is built around a Cypress EZ-USB FX2LP microcontroller — an 8051-compatible chip with built-in USB 2.0 controller. It can sample 8 channels up to 24MHz.
In sigrok, we use the open-source fx2lafw firmware for this logic analyzer.
See Saleae Logic/Info for more details (such as lsusb -vvv output) about the device.
See Saleae Logic16 for the successor product of the Saleae Logic.
Hardware
- Main chip: Cypress CY7C68013A-56PVXC (FX2LP)
- ESD protection: ST DVIULC6-4SC6
- 3.3V voltage regulator: ST LD33C
- I2C EEPROM: Microchip 24LC00
- Crystal: 24MHz
The case has four Torx T2 screws you need to remove in order to be able to open it.
Photos
Device, top
Device with two E-Z-Hooks
Device, open
PCB, front
PCB, back
Saleae Logic collection
Protocol
Since we use the open-source fx2lafw firmware for this device, we don't need to know the protocol.
However, for those interested in this, see our old vendor protocol docs.