Difference between revisions of "GW Instek GPD series"

From sigrok
Jump to navigation Jump to search
m (Uwe Hermann moved page GW Instek-GPD series to GW Instek GPD series without leaving a redirect)
 
(7 intermediate revisions by 2 users not shown)
Line 1: Line 1:
{{Infobox power supply
{{Infobox power supply
| image              =  
| image              = [[File:Gwinstek-gpd-3303s.png|180px]]
| name                = GW Instek GPD series
| name                = GW Instek GPD series
| status              = supported
| status              = supported
Line 14: Line 14:
}}
}}


The '''GW Instek GPD''' series are 2/3/4 channel programmable linear DC power supplies with USB/serial connectivity.
The '''GW Instek GPD series''' are 2/3/4 channel programmable linear DC power supplies with USB/serial connectivity.


== Devices ==
== Devices ==
Line 25: Line 25:
!Current range
!Current range
!Power
!Power
!Comments


|-
|-
| GPD-2303S
| [[GW Instek GPD-2303S|GPD-2303S]]
| 2
| 2
| 0-30 V, 0-30 V
| 0-30 V, 0-30 V
| 0-3 A, 0-3 A
| 0-3 A, 0-3 A
| 180 W
| 180 W
|


|-
|-
| GPD-3303S
| [[GW Instek GPD-3303S|GPD-3303S]]
| 3
| 3
| 0-30 V, 0-30 V, 2.5/3.3/5.0 V
| 0-30 V, 0-30 V, 2.5/3.3/5.0 V
| 0-3 A, 0-3 A, 0-3 A
| 0-3 A, 0-3 A, 0-3 A
| 195 W
| 195 W
|


|-
|-
Line 49: Line 46:
| 0-3 A, 0-3 A, 0-3 A or 0-1 A, 0-1 A
| 0-3 A, 0-3 A, 0-3 A or 0-1 A, 0-1 A
| 195 W
| 195 W
|


|-
|-
Line 57: Line 53:
| 0-3 A, 0-3 A, 0-3 A
| 0-3 A, 0-3 A, 0-3 A
| 195 W
| 195 W
|


|}
|}
So far, only the GPD-2303S is supported and tested. Adding support for the other devices should be relatively easy for someone with hardware access, though. Patches welcome!
== Hardware ==
There was two hardware revisions (versions) of these units released. Model numbes did not change so it is difficult to
determine whether unit is the "old" or "new" hardware revision.
However, at least on GPD-3303S there is slight change to unit front panels;
older units have slight space in output jacks between "CH1" and "FIXED" channel, while newer units have even spacing.
It would appear that older hardware revision units have firmware version < v2.00, but this has not been confirmed (based on anecdotal evidence only).


== Protocol ==
== Protocol ==


See the [https://www.gwinstek.com/en-US/products/downloadSeriesDownNew/7840/1477 vendor user manual] for details.
These units use SCPI like command protocol. However, units do not implement all mandatory SCPI commands.
 
There appears to be difference in the protocol between old and new hardware revision units.
Output from STATUS? command differs:
 
{| class="wikitable"
!Bit
!New Units
!Old Units
|-
|0
|colspan="2" style="text-align: center;"|CH1 (0=CC, 1=CV)
|-
|1
|colspan="2" style="text-align: center;"|CH2 (0=Cc, 1=CV)
|-
|2,3
|colspan="2" style="text-align: center;"|Tracking (01=Independent, 11=Series, 10=Parallel)
|-
|4
|colspan="2" style="text-align: center;"|Beep (0=OFF, 1=ON)
|-
|5
|Output (0=OFF, 1=ON)
|N/A
|-
|6
|rowspan="2"|Baud (00=115200, 01=57600, 00=9600)
|Output (0=OFF, 1=ON)
|-
|7
|N/A
|}
 
 
Example output to *STATUS? command:
 
Old units:
<pre>
0 0 0 1 0 X 0 X 
bit0:(CH1)0=CC,1=CV;bit1:(CH2)0=CC,1=CV;bit23=(TRACK)01=INDEP,11=SER,10=PAR;
bit4:(BEEP)0=OFF,1=ON;bit6:(OUT)0=OFF,1=ON;
</pre>
 
 
New units:
 
<pre>
0 0 0 1 0 0 0 0
</pre>
 
 
See the [https://www.gwinstek.com/en-US/products/downloadSeriesDownNew/7840/1477 vendor user manual] for more details.


== Resources ==
== Resources ==

Latest revision as of 10:07, 3 August 2020

GW Instek GPD series
Gwinstek-gpd-3303s.png
Status supported
Source code gwinstek-gpd
Channels 2/3/4
Voltage/current (CH1) 0-30V / 0-3A
Voltage/current (CH2) 0-30V / 0-3A
Voltage/current (CH3) various
Voltage/current (CH4) various
Connectivity USB/serial
Features memory save/recall, key lock
Website gwinstek.com

The GW Instek GPD series are 2/3/4 channel programmable linear DC power supplies with USB/serial connectivity.

Devices

Device Channels Voltage range Current range Power
GPD-2303S 2 0-30 V, 0-30 V 0-3 A, 0-3 A 180 W
GPD-3303S 3 0-30 V, 0-30 V, 2.5/3.3/5.0 V 0-3 A, 0-3 A, 0-3 A 195 W
GPD-4303S 4 0-30 V, 0-30 V, 0-5 V or 5-10 V, 0-5 V 0-3 A, 0-3 A, 0-3 A or 0-1 A, 0-1 A 195 W
GPD-3303D 3 0-30 V, 0-30 V, 2.5/3.3/5.0 V 0-3 A, 0-3 A, 0-3 A 195 W

So far, only the GPD-2303S is supported and tested. Adding support for the other devices should be relatively easy for someone with hardware access, though. Patches welcome!

Hardware

There was two hardware revisions (versions) of these units released. Model numbes did not change so it is difficult to determine whether unit is the "old" or "new" hardware revision. However, at least on GPD-3303S there is slight change to unit front panels; older units have slight space in output jacks between "CH1" and "FIXED" channel, while newer units have even spacing.

It would appear that older hardware revision units have firmware version < v2.00, but this has not been confirmed (based on anecdotal evidence only).

Protocol

These units use SCPI like command protocol. However, units do not implement all mandatory SCPI commands.

There appears to be difference in the protocol between old and new hardware revision units. Output from STATUS? command differs:

Bit New Units Old Units
0 CH1 (0=CC, 1=CV)
1 CH2 (0=Cc, 1=CV)
2,3 Tracking (01=Independent, 11=Series, 10=Parallel)
4 Beep (0=OFF, 1=ON)
5 Output (0=OFF, 1=ON) N/A
6 Baud (00=115200, 01=57600, 00=9600) Output (0=OFF, 1=ON)
7 N/A


Example output to *STATUS? command:

Old units: 

0 0 0 1 0 X 0 X  
bit0:(CH1)0=CC,1=CV;bit1:(CH2)0=CC,1=CV;bit23=(TRACK)01=INDEP,11=SER,10=PAR;
bit4:(BEEP)0=OFF,1=ON;bit6:(OUT)0=OFF,1=ON;


New units: 

0 0 0 1 0 0 0 0


See the vendor user manual for more details.

Resources

Retrieved from "https://sigrok.org/w/index.php?title=GW_Instek_GPD_series&oldid=15346"