Difference between revisions of "SainSmart DDS120"

**SainSmart DDS120**
Status	supported
Source code	hantek-6xxx
Channels	2
Samplerate	50MHz
Analog bandwidth	20MHz
Vertical resolution	8bit
Triggers	none (SW-only)
Input impedance	1MΩ‖25pF
Memory	none
Display	none
Connectivity	USB
Website	sainsmart.com

Latest revision as of 15:17, 2 October 2018

The SainSmart DDS120 is a USB-based, 2-channel oscilloscope with an analog bandwidth of 20MS/s and 50MS/s sampling rate.

This device appears to be a rebadge of the Rocktech BM102 (or vice versa). The lsusb is exactly the same, the PCB is exactly the same (both have a "656517" and "102LJT1402" silkscreen), and the components used appear to be the same as well.

The device was apparently created by someone named "buudai" in 2012 (also reflected in the lsusb and in the former buudai.com website).

See SainSmart DDS120/Info for more details (such as lsusb -v output) about the device.

Hardware

USB: Cypress CY7C68013A-100AXC (FX2LP) (datasheet)
64-kbyte I²C EEPROM: Microchip 24LC64I (datasheet)
Crystal: 24MHz
145 MHz FastFET Opamps: AD8065ART-R2: (datasheet)

Or in newer hardware:

Dual 8bit, 100MSPS ADC: MXTronix MXT2088 (datasheet)
145 MHz FastFET Opamps: AD8065: (datasheet)
4x CMOS differential 4-channel analog mux/demux with logic-level conversion: Texas Instruments CD4052B(M) (datasheet)

Photos

Teardown 1:

Device, top
PCB, front
PCB, front
PCB, front
PCB, front
PCB, front
PCB, front
PCB, back
PCB, back
Box
Box
Box

Teardown 2 (purchased 03/2016):

Sticker
Package contents
Device, top
Device, bottom
USB
Connectors
PCB, top
PCB, bottom
MXTronix MXT2088
Cypress FX2
Microchip 24LC64I
TI CD4052BM
AMS1117-3.3
Unknown IC

Protocol

We use an open-source firmware for this device (i.e., not the vendor firmware/protocol), hence we do not need to know the vendor protocol. There is some historic vendor firmware/protocol info for those interested, though.

Firmware

In order to use this device, the sigrok-firmware-fx2lafw (>= 0.1.4) firmware is required.

The firmware was originally written by Jochen Hoenicke (see README for details), thanks a lot!

Note: The firmware is not flashed into the device permanently! You only need to make it available in the usual place where libsigrok looks for firmware files, it will be used automatically (and "uploaded" to the Cypress FX2's SRAM every time you attach the device to a USB port).

Note: On Windows, you will have to assign the WinUSB driver via Zadig twice: the first time for the initial USB VID/PID the device has when attaching it via USB (04b4:602a or 04b5:602a, depending on which vendor driver is currently being used by the device), and a second time after the firmware has been uploaded to the device and the device has "renumerated" with a different VID/PID pair (1d50:608e).

See this section for technical details about the firmware/hardware.

Resources

@@ Line 1: / Line 1: @@
-[[File:Dds120 mugshot.png|thumb|right|SainSmart DDS120]]
+{{Infobox oscilloscope
+| image               = [[File:Dds120 mugshot.png|180px]]
+| name                = SainSmart DDS120
+| status              = supported
+| source_code_dir     = hantek-6xxx
+| channels            = 2
+| samplerate          = 50MHz
+| samplerate_equiv    =
+| bandwidth           = 20MHz
+| vertical_resolution = 8bit
+| triggers            = none (SW-only)
+| input_impedance     = 1MΩ‖25pF
+| memory              = none
+| display             = none
+| connectivity        = USB
+| features            =
+| website             = [http://www.sainsmart.com/sainsmart-dds-120-20m-50m-s-virtual-oscilloscope-silver.html sainsmart.com]
+}}
-The [http://www.sainsmart.com/sainsmart-dds-120-20m-50m-s-virtual-oscilloscope-silver.html SainSmart DDS120] is a USB-based, 2-channel oscilloscope with an analog bandwidth of 20MS/s and 48MS/s sampling rate.
+The '''SainSmart DDS120''' is a USB-based, 2-channel oscilloscope with an analog bandwidth of 20MS/s and 50MS/s sampling rate.
+This device appears to be a rebadge of the [[Rocktech BM102]] (or vice versa). The [[SainSmart DDS120/Info|lsusb]] is exactly the same, the PCB is exactly the same (both have a "656517" and "102LJT1402" silkscreen), and the components used appear to be the same as well.
+The device was apparently [https://translate.google.de/translate?sl=auto&tl=en&js=y&prev=_t&hl=en&ie=UTF-8&u=https%3A%2F%2Fweb.archive.org%2Fweb%2F20140520231246%2Fhttp%3A%2F%2Fbbs.21ic.com%2Ficview-350047-1-1.html&edit-text=&act=url created by someone named "buudai"] in 2012 (also reflected in the [[SainSmart DDS120/Info|lsusb]] and in the former [https://web.archive.org/web/20130403082149/http://www.buudai.com/ buudai.com] website).
 See [[SainSmart DDS120/Info]] for more details (such as '''lsusb -v''' output) about the device.
+== Hardware ==
 * '''USB''': [http://www.cypress.com/documentation/datasheets/cy7c68013a-cy7c68014a-cy7c68015a-cy7c68016a-ez-usb-fx2lp-usb Cypress CY7C68013A-100AXC] (FX2LP) ([http://www.cypress.com/file/138911/download datasheet])
-* '''64-kbyte I²C EEPROM''': [http://www.microchip.com/wwwproducts/Devices.aspx?dDocName=en010831 Microchip 24LC641] ([http://ww1.microchip.com/downloads/en/DeviceDoc/21189f.pdf datasheet])
+* '''64-kbyte I²C EEPROM''': [http://www.microchip.com/wwwproducts/Devices.aspx?dDocName=en010831 Microchip 24LC64I] ([http://ww1.microchip.com/downloads/en/DeviceDoc/21189f.pdf datasheet])
 * '''Crystal''': 24MHz
-* '''AD''': AD8065ART-R2: ([http://www.analog.com/static/imported-files/data_sheets/AD8065_8066.pdf datasheet])
+* '''145 MHz FastFET Opamps''': [http://www.analog.com/en/products/amplifiers/operational-amplifiers/jfet-input-amplifiers/ad8065.html#product-overview AD8065ART-R2]: ([http://www.analog.com/static/imported-files/data_sheets/AD8065_8066.pdf datasheet])
-or in newer hardware
-* '''AD''': MXT2088 ([http://www.mxtronics.com/n107/n124/n181/n184/c692/attr/2630.pdf datasheet])
-* '''Opamp''': Analog devices AD8065 (OPAMP)
-* '''MUX''': Texas Instruments CD4052B (2 x 1:4 MUX)
-== Firmware ==
+'''Or in newer hardware:'''
-The Sainsmart firmware is contained on an i2c eeprom. The FX2 boots directly into that firmware. Loading another firmware is possible and a modified hantek 6022be booted fine.
+* '''Dual 8bit, 100MSPS ADC''': [https://translate.google.com/translate?hl=en&sl=zh-CN&tl=en&u=http%3A%2F%2Fwww.mxtronics.com%2Fn107%2Fn124%2Fn181%2Fn184%2Fc692%2Fcontent.html MXTronix MXT2088] ([http://www.mxtronics.com/n107/n124/n181/n184/c692/attr/2630.pdf datasheet])
+* '''145 MHz FastFET Opamps''': [http://www.analog.com/en/products/amplifiers/operational-amplifiers/jfet-input-amplifiers/ad8065.html#product-overview AD8065]: ([http://www.analog.com/static/imported-files/data_sheets/AD8065_8066.pdf datasheet])
+* 4x '''CMOS differential 4-channel analog mux/demux with logic-level conversion''': [http://www.ti.com/product/cd4052b/description Texas Instruments CD4052B(M)] ([http://www.ti.com/lit/gpn/cd4052b datasheet])
-== Vendor Protocol ==
+== Photos ==
-{| border="0" style="font-size: smaller" class="alternategrey sortable sigroktable"
-|-
-!Oscilloscope command
-!bRequest value
-!Notes
-|-
-|Set CH0 coupling 	||0x24 	||Possible values: 0x00, 0x08 (AC-coupling, DC-coupling).
-|-
-|Set CH1 coupling 	||0x25 	||Possible values: 0x20, 0x10 (AC-coupling, DC-coupling).
-|-
-|Set CH0 voltage range 	||0x22 	||Possible values: 0x08, 0x04, 0x00, 0x06, 0x02 (50mV, 100mV, 200mV, 500mV, 1-5V).
-|-
-|Set CH1 voltage range 	||0x23 	||Possible values: 0x20, 0x10, 0x00, 0x12, 0x02 (50mV, 100mV, 200mV, 500mV, 1-5V).
-|-
-|Set sampling rate 	||0x94 	||Possible values: 0x11, 0x01, 0x10 (240kHz, 2.4MHz, 48MHz).
-|-
-|Trigger oscilloscope 	||0x33 	||Possible values: 0x00 == start sampling.
-|-
-|}
-== Photos ==
+'''Teardown 1''':
 <gallery>
+File:Dds120 mugshot.png|<small>Device, top</small>
 File:DDS120 Top 20141024 0540p.jpg|<small>PCB, front</small>
 File:Sainsmart dds120 front 1.jpg|<small>PCB, front</small>
 File:Sainsmart dds120 front 2.jpg|<small>PCB, front</small>
@@ Line 50: / Line 51: @@
 File:Sainsmart dds120 front 4.jpg|<small>PCB, front</small>
 File:Sainsmart dds120 front 5.jpg|<small>PCB, front</small>
 File:Sainsmart dds120 back 1.jpg|<small>PCB, back</small>
 File:Sainsmart dds120 back 2.jpg|<small>PCB, back</small>
 File:Sainsmart dds120 box 1.jpg|<small>Box</small>
 File:Sainsmart dds120 box 2.jpg|<small>Box</small>
@@ Line 59: / Line 58: @@
 </gallery>
-== Resources ==
+'''Teardown 2 (purchased 03/2016)''':
+<gallery>
+File:Saintsmart dds120 sticker.jpg|<small>Sticker</small>
+File:Saintsmart dds120 package contents.jpg|<small>Package contents</small>
+File:Saintsmart dds120 device top.jpg|<small>Device, top</small>
+File:Saintsmart dds120 device bottom.jpg|<small>Device, bottom</small>
+File:Saintsmart dds120 usb.jpg|<small>USB</small>
+File:Saintsmart dds120 connectors.jpg|<small>Connectors</small>
+File:Saintsmart dds120 pcb top.jpg|<small>PCB, top</small>
+File:Saintsmart dds120 pcb bottom.jpg|<small>PCB, bottom</small>
+File:Saintsmart dds120 mxt2088.jpg|<small>MXTronix MXT2088</small>
+File:Saintsmart dds120 fx2.jpg|<small>Cypress FX2</small>
+File:Saintsmart dds120 microchip 24lc64i.jpg|<small>Microchip 24LC64I</small>
+File:Saintsmart dds120 ti cd4052bm.jpg|<small>TI CD4052BM</small>
+File:Saintsmart dds120 ams1117-3.3.jpg|<small>AMS1117-3.3</small>
+File:Saintsmart dds120 nais 210eh 347.jpg|<small>Unknown IC</small>
+</gallery>
-* [http://www.eevblog.com/forum/testgear/sainsmart-dds120-usb-oscilloscope-(buudai-bm102)/ EEVBlog forum thread]
+== Protocol ==
-* [http://www.360customs.de/en/2014/10/usb-oszilloskop-sainsmart-dds120-2-kanal-20mhz-50msps-buudairocktech-bm102/ Detailed description of the hardware]
-[[Category:Device]]
-[[Category:Oscilloscope]]
-== Gain stage ==
+We use an open-source firmware for this device (i.e., not the vendor firmware/protocol), hence we do not need to know the vendor protocol. There is some [[SainSmart_DDS120/Info#Vendor_firmware|historic vendor firmware/protocol info]] for those interested, though.
-The gain stage is 2 stage approach. -6dB and -20dB on the first stage (attentuator). The second stage is then doing the gain by 3 different resistor values switched into the feedback loop. The following does not correlate with measure on real hardware, there is a 6th gain position that is working though. It is very similar to another gain and was most likely omitted because of that.
+== Firmware ==
- #Channel 0:
+In order to use this device, the [[fx2lafw|sigrok-firmware-fx2lafw]] (>= 0.1.4) firmware is required.
- PC1=1; PC2=0; PC3= 0 -> Gain x0.1 = -20dB -> 0x02 (1V)
- PC1=1; PC2=0; PC3= 1 -> Gain x0.2 = -14dB -> 0x0A (0.5V)
- PC1=1; PC2=1; PC3= 0 -> Gain x0.4 =  -8dB -> 0x06 (0.250V)
- PC1=0; PC2=0; PC3= 0 -> Gain x0.5 =  -6dB -> 0x00 (0.200V)
- PC1=0; PC2=0; PC3= 1 -> Gain x1   =   0dB -> 0x08 (0.100V)
- PC1=0; PC2=1; PC3= 0 -> Gain x2   =  +6dB -> 0x04 (0.050V)
- #Channel 1:
+The firmware was originally written by Jochen Hoenicke (see [http://sigrok.org/gitweb/?p=sigrok-firmware-fx2lafw.git;a=blob;f=README README] for details), thanks a lot!
- PE1=1; PC4=0; PC5= 0 -> Gain x0.1 = -20dB -> 0x02 (1V)
- PE1=1; PC4=0; PC5= 1 -> Gain x0.2 = -14dB -> 0x22 (0.5V)
- PE1=1; PC4=1; PC5= 0 -> Gain x0.4 =  -8dB -> 0x12 (0.250V)
- PE1=0; PC4=0; PC5= 0 -> Gain x0.5 =  -6dB -> 0x00 (0.200V)
- PE1=0; PC4=0; PC5= 1 -> Gain x1   =   0dB -> 0x20 (0.100V)
- PE1=0; PC4=1; PC5= 0 -> Gain x2   =  +6dB -> 0x10 (0.050V)
-== AC/DC coupling ==
+'''Note''': The firmware is '''not''' flashed into the device permanently! You only need to make it available in the usual place where [[libsigrok]] looks for firmware files, it will be used automatically (and "uploaded" to the Cypress FX2's SRAM every time you attach the device to a USB port).
-The coupling is controlled via 2 PhotoMOS chips.
+'''Note''': On Windows, you will have to [[Windows#Device_specific_USB_driver|assign the WinUSB driver via Zadig]] '''twice''': the first time for the initial USB VID/PID the device has when attaching it via USB (04b4:602a or 04b5:602a, depending on which vendor driver is currently being used by the device), and a second time after the firmware has been uploaded to the device and the device has "renumerated" with a different VID/PID pair (1d50:608e).
- #Channel 0:
+See [[SainSmart_DDS120/Info#Open-source_firmware_details|this section]] for technical details about the firmware/hardware.
- PE3=0 Disable AC-coupling capacitor (DC-Coupling)
- PE3=1 Enable AC-coupling capacitor
- #Channel 1:
+== Resources ==
- PE0=0 Disable AC-coupling capacitor (DC-Coupling)
- PE0=1 Enable AC-coupling capacitor
-== 1kHz Calibration square wave ==
+* [http://www.eevblog.com/forum/testgear/sainsmart-dds120-usb-oscilloscope-(buudai-bm102)/ EEVBlog forum thread]
+* [http://www.360customs.de/en/2014/10/usb-oszilloskop-sainsmart-dds120-2-kanal-20mhz-50msps-buudairocktech-bm102/ Detailed description of the hardware]
+* [http://www.sainsmart.com/sainsmart-dds-120-20m-50m-s-virtual-oscilloscope-silver.html Vendor product page]
+* [https://www.eevblog.com/forum/testgear/saintsmart-dds120-software-download/msg818124/#msg818124 Vendor software download links]
-Pin PE2 controlls the level of the calibration output on the pcb. This is most likely driven by an ISR timer from the 8051 core of the FX2 chip.
+[[Category:Device]]
+[[Category:Oscilloscope]]
+[[Category:Supported]]

Difference between revisions of "SainSmart DDS120"

Latest revision as of 15:17, 2 October 2018

Contents

Hardware

Photos

Protocol

Firmware

Resources

Navigation menu

Difference between revisions of "SainSmart DDS120"

Latest revision as of 15:17, 2 October 2018

Hardware

Photos

Protocol

Firmware

Resources

Navigation menu

Search