[libsigrok.git] / src / hardware / asix-sigma / asix-sigma.c

/*
 * This file is part of the libsigrok project.
 *
 * Copyright (C) 2010-2012 Håvard Espeland <gus@ping.uio.no>,
 * Copyright (C) 2010 Martin Stensgård <mastensg@ping.uio.no>
 * Copyright (C) 2010 Carl Henrik Lunde <chlunde@ping.uio.no>
 *
 * This program is free software: you can redistribute it and/or modify
 * it under the terms of the GNU General Public License as published by
 * the Free Software Foundation, either version 3 of the License, or
 * (at your option) any later version.
 *
 * This program is distributed in the hope that it will be useful,
 * but WITHOUT ANY WARRANTY; without even the implied warranty of
 * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
 * GNU General Public License for more details.
 *
 * You should have received a copy of the GNU General Public License
 * along with this program.  If not, see <http://www.gnu.org/licenses/>.
 */

/*
 * ASIX SIGMA/SIGMA2 logic analyzer driver
 */

#include <glib.h>
#include <glib/gstdio.h>
#include <ftdi.h>
#include <string.h>
#include <unistd.h>
#include "libsigrok.h"
#include "libsigrok-internal.h"
#include "asix-sigma.h"

#define USB_VENDOR                      0xa600
#define USB_PRODUCT                     0xa000
#define USB_DESCRIPTION                 "ASIX SIGMA"
#define USB_VENDOR_NAME                 "ASIX"
#define USB_MODEL_NAME                  "SIGMA"

SR_PRIV struct sr_dev_driver asix_sigma_driver_info;
static int dev_acquisition_stop(struct sr_dev_inst *sdi, void *cb_data);

/*
 * The ASIX Sigma supports arbitrary integer frequency divider in
 * the 50MHz mode. The divider is in range 1...256 , allowing for
 * very precise sampling rate selection. This driver supports only
 * a subset of the sampling rates.
 */
static const uint64_t samplerates[] = {
        SR_KHZ(200),    /* div=250 */
        SR_KHZ(250),    /* div=200 */
        SR_KHZ(500),    /* div=100 */
        SR_MHZ(1),      /* div=50  */
        SR_MHZ(5),      /* div=10  */
        SR_MHZ(10),     /* div=5   */
        SR_MHZ(25),     /* div=2   */
        SR_MHZ(50),     /* div=1   */
        SR_MHZ(100),    /* Special FW needed */
        SR_MHZ(200),    /* Special FW needed */
};

/*
 * Channel numbers seem to go from 1-16, according to this image:
 * http://tools.asix.net/img/sigma_sigmacab_pins_720.jpg
 * (the cable has two additional GND pins, and a TI and TO pin)
 */
static const char *channel_names[] = {
        "1", "2", "3", "4", "5", "6", "7", "8",
        "9", "10", "11", "12", "13", "14", "15", "16",
};

static const uint32_t drvopts[] = {
        SR_CONF_LOGIC_ANALYZER,
};

static const uint32_t devopts[] = {
        SR_CONF_LIMIT_MSEC | SR_CONF_GET | SR_CONF_SET,
        SR_CONF_LIMIT_SAMPLES | SR_CONF_SET,
        SR_CONF_SAMPLERATE | SR_CONF_GET | SR_CONF_SET | SR_CONF_LIST,
        SR_CONF_TRIGGER_MATCH | SR_CONF_LIST,
        SR_CONF_CAPTURE_RATIO | SR_CONF_GET | SR_CONF_SET,
};

static const int32_t trigger_matches[] = {
        SR_TRIGGER_ZERO,
        SR_TRIGGER_ONE,
        SR_TRIGGER_RISING,
        SR_TRIGGER_FALLING,
};

static const char *sigma_firmware_files[] = {
        /* 50 MHz, supports 8 bit fractions */
        FIRMWARE_DIR "/asix-sigma-50.fw",
        /* 100 MHz */
        FIRMWARE_DIR "/asix-sigma-100.fw",
        /* 200 MHz */
        FIRMWARE_DIR "/asix-sigma-200.fw",
        /* Synchronous clock from pin */
        FIRMWARE_DIR "/asix-sigma-50sync.fw",
        /* Frequency counter */
        FIRMWARE_DIR "/asix-sigma-phasor.fw",
};

static int sigma_read(void *buf, size_t size, struct dev_context *devc)
{
        int ret;

        ret = ftdi_read_data(&devc->ftdic, (unsigned char *)buf, size);
        if (ret < 0) {
                sr_err("ftdi_read_data failed: %s",
                       ftdi_get_error_string(&devc->ftdic));
        }

        return ret;
}

static int sigma_write(void *buf, size_t size, struct dev_context *devc)
{
        int ret;

        ret = ftdi_write_data(&devc->ftdic, (unsigned char *)buf, size);
        if (ret < 0) {
                sr_err("ftdi_write_data failed: %s",
                       ftdi_get_error_string(&devc->ftdic));
        } else if ((size_t) ret != size) {
                sr_err("ftdi_write_data did not complete write.");
        }

        return ret;
}

static int sigma_write_register(uint8_t reg, uint8_t *data, size_t len,
                                struct dev_context *devc)
{
        size_t i;
        uint8_t buf[len + 2];
        int idx = 0;

        buf[idx++] = REG_ADDR_LOW | (reg & 0xf);
        buf[idx++] = REG_ADDR_HIGH | (reg >> 4);

        for (i = 0; i < len; ++i) {
                buf[idx++] = REG_DATA_LOW | (data[i] & 0xf);
                buf[idx++] = REG_DATA_HIGH_WRITE | (data[i] >> 4);
        }

        return sigma_write(buf, idx, devc);
}

static int sigma_set_register(uint8_t reg, uint8_t value, struct dev_context *devc)
{
        return sigma_write_register(reg, &value, 1, devc);
}

static int sigma_read_register(uint8_t reg, uint8_t *data, size_t len,
                               struct dev_context *devc)
{
        uint8_t buf[3];

        buf[0] = REG_ADDR_LOW | (reg & 0xf);
        buf[1] = REG_ADDR_HIGH | (reg >> 4);
        buf[2] = REG_READ_ADDR;

        sigma_write(buf, sizeof(buf), devc);

        return sigma_read(data, len, devc);
}

static uint8_t sigma_get_register(uint8_t reg, struct dev_context *devc)
{
        uint8_t value;

        if (1 != sigma_read_register(reg, &value, 1, devc)) {
                sr_err("sigma_get_register: 1 byte expected");
                return 0;
        }

        return value;
}

static int sigma_read_pos(uint32_t *stoppos, uint32_t *triggerpos,
                          struct dev_context *devc)
{
        uint8_t buf[] = {
                REG_ADDR_LOW | READ_TRIGGER_POS_LOW,

                REG_READ_ADDR | NEXT_REG,
                REG_READ_ADDR | NEXT_REG,
                REG_READ_ADDR | NEXT_REG,
                REG_READ_ADDR | NEXT_REG,
                REG_READ_ADDR | NEXT_REG,
                REG_READ_ADDR | NEXT_REG,
        };
        uint8_t result[6];

        sigma_write(buf, sizeof(buf), devc);

        sigma_read(result, sizeof(result), devc);

        *triggerpos = result[0] | (result[1] << 8) | (result[2] << 16);
        *stoppos = result[3] | (result[4] << 8) | (result[5] << 16);

        /* Not really sure why this must be done, but according to spec. */
        if ((--*stoppos & 0x1ff) == 0x1ff)
                *stoppos -= 64;

        if ((*--triggerpos & 0x1ff) == 0x1ff)
                *triggerpos -= 64;

        return 1;
}

static int sigma_read_dram(uint16_t startchunk, size_t numchunks,
                           uint8_t *data, struct dev_context *devc)
{
        size_t i;
        uint8_t buf[4096];
        int idx = 0;

        /* Send the startchunk. Index start with 1. */
        buf[0] = startchunk >> 8;
        buf[1] = startchunk & 0xff;
        sigma_write_register(WRITE_MEMROW, buf, 2, devc);

        /* Read the DRAM. */
        buf[idx++] = REG_DRAM_BLOCK;
        buf[idx++] = REG_DRAM_WAIT_ACK;

        for (i = 0; i < numchunks; ++i) {
                /* Alternate bit to copy from DRAM to cache. */
                if (i != (numchunks - 1))
                        buf[idx++] = REG_DRAM_BLOCK | (((i + 1) % 2) << 4);

                buf[idx++] = REG_DRAM_BLOCK_DATA | ((i % 2) << 4);

                if (i != (numchunks - 1))
                        buf[idx++] = REG_DRAM_WAIT_ACK;
        }

        sigma_write(buf, idx, devc);

        return sigma_read(data, numchunks * CHUNK_SIZE, devc);
}

/* Upload trigger look-up tables to Sigma. */
static int sigma_write_trigger_lut(struct triggerlut *lut, struct dev_context *devc)
{
        int i;
        uint8_t tmp[2];
        uint16_t bit;

        /* Transpose the table and send to Sigma. */
        for (i = 0; i < 16; ++i) {
                bit = 1 << i;

                tmp[0] = tmp[1] = 0;

                if (lut->m2d[0] & bit)
                        tmp[0] |= 0x01;
                if (lut->m2d[1] & bit)
                        tmp[0] |= 0x02;
                if (lut->m2d[2] & bit)
                        tmp[0] |= 0x04;
                if (lut->m2d[3] & bit)
                        tmp[0] |= 0x08;

                if (lut->m3 & bit)
                        tmp[0] |= 0x10;
                if (lut->m3s & bit)
                        tmp[0] |= 0x20;
                if (lut->m4 & bit)
                        tmp[0] |= 0x40;

                if (lut->m0d[0] & bit)
                        tmp[1] |= 0x01;
                if (lut->m0d[1] & bit)
                        tmp[1] |= 0x02;
                if (lut->m0d[2] & bit)
                        tmp[1] |= 0x04;
                if (lut->m0d[3] & bit)
                        tmp[1] |= 0x08;

                if (lut->m1d[0] & bit)
                        tmp[1] |= 0x10;
                if (lut->m1d[1] & bit)
                        tmp[1] |= 0x20;
                if (lut->m1d[2] & bit)
                        tmp[1] |= 0x40;
                if (lut->m1d[3] & bit)
                        tmp[1] |= 0x80;

                sigma_write_register(WRITE_TRIGGER_SELECT0, tmp, sizeof(tmp),
                                     devc);
                sigma_set_register(WRITE_TRIGGER_SELECT1, 0x30 | i, devc);
        }

        /* Send the parameters */
        sigma_write_register(WRITE_TRIGGER_SELECT0, (uint8_t *) &lut->params,
                             sizeof(lut->params), devc);

        return SR_OK;
}

static void clear_helper(void *priv)
{
        struct dev_context *devc;

        devc = priv;

        ftdi_deinit(&devc->ftdic);
}

static int dev_clear(const struct sr_dev_driver *di)
{
        return std_dev_clear(di, clear_helper);
}

static int init(struct sr_dev_driver *di, struct sr_context *sr_ctx)
{
        return std_init(sr_ctx, di, LOG_PREFIX);
}

static GSList *scan(struct sr_dev_driver *di, GSList *options)
{
        struct sr_dev_inst *sdi;
        struct drv_context *drvc;
        struct dev_context *devc;
        GSList *devices;
        struct ftdi_device_list *devlist;
        char serial_txt[10];
        uint32_t serial;
        int ret;
        unsigned int i;

        (void)options;

        drvc = di->priv;

        devices = NULL;

        devc = g_malloc0(sizeof(struct dev_context));

        ftdi_init(&devc->ftdic);

        /* Look for SIGMAs. */

        if ((ret = ftdi_usb_find_all(&devc->ftdic, &devlist,
            USB_VENDOR, USB_PRODUCT)) <= 0) {
                if (ret < 0)
                        sr_err("ftdi_usb_find_all(): %d", ret);
                goto free;
        }

        /* Make sure it's a version 1 or 2 SIGMA. */
        ftdi_usb_get_strings(&devc->ftdic, devlist->dev, NULL, 0, NULL, 0,
                             serial_txt, sizeof(serial_txt));
        sscanf(serial_txt, "%x", &serial);

        if (serial < 0xa6010000 || serial > 0xa602ffff) {
                sr_err("Only SIGMA and SIGMA2 are supported "
                       "in this version of libsigrok.");
                goto free;
        }

        sr_info("Found ASIX SIGMA - Serial: %s", serial_txt);

        devc->cur_samplerate = samplerates[0];
        devc->period_ps = 0;
        devc->limit_msec = 0;
        devc->cur_firmware = -1;
        devc->num_channels = 0;
        devc->samples_per_event = 0;
        devc->capture_ratio = 50;
        devc->use_triggers = 0;

        /* Register SIGMA device. */
        sdi = g_malloc0(sizeof(struct sr_dev_inst));
        sdi->status = SR_ST_INITIALIZING;
        sdi->vendor = g_strdup(USB_VENDOR_NAME);
        sdi->model = g_strdup(USB_MODEL_NAME);
        sdi->driver = di;

        for (i = 0; i < ARRAY_SIZE(channel_names); i++)
                sr_channel_new(sdi, i, SR_CHANNEL_LOGIC, TRUE,
                                    channel_names[i]);

        devices = g_slist_append(devices, sdi);
        drvc->instances = g_slist_append(drvc->instances, sdi);
        sdi->priv = devc;

        /* We will open the device again when we need it. */
        ftdi_list_free(&devlist);

        return devices;

free:
        ftdi_deinit(&devc->ftdic);
        g_free(devc);
        return NULL;
}

static GSList *dev_list(const struct sr_dev_driver *di)
{
        return ((struct drv_context *)(di->priv))->instances;
}

/*
 * Configure the FPGA for bitbang mode.
 * This sequence is documented in section 2. of the ASIX Sigma programming
 * manual. This sequence is necessary to configure the FPGA in the Sigma
 * into Bitbang mode, in which it can be programmed with the firmware.
 */
static int sigma_fpga_init_bitbang(struct dev_context *devc)
{
        uint8_t suicide[] = {
                0x84, 0x84, 0x88, 0x84, 0x88, 0x84, 0x88, 0x84,
        };
        uint8_t init_array[] = {
                0x01, 0x03, 0x03, 0x01, 0x01, 0x01, 0x01, 0x01,
                0x01, 0x01,
        };
        int i, ret, timeout = 10000;
        uint8_t data;

        /* Section 2. part 1), do the FPGA suicide. */
        sigma_write(suicide, sizeof(suicide), devc);
        sigma_write(suicide, sizeof(suicide), devc);
        sigma_write(suicide, sizeof(suicide), devc);
        sigma_write(suicide, sizeof(suicide), devc);

        /* Section 2. part 2), do pulse on D1. */
        sigma_write(init_array, sizeof(init_array), devc);
        ftdi_usb_purge_buffers(&devc->ftdic);

        /* Wait until the FPGA asserts D6/INIT_B. */
        for (i = 0; i < timeout; i++) {
                ret = sigma_read(&data, 1, devc);
                if (ret < 0)
                        return ret;
                /* Test if pin D6 got asserted. */
                if (data & (1 << 5))
                        return 0;
                /* The D6 was not asserted yet, wait a bit. */
                g_usleep(10000);
        }

        return SR_ERR_TIMEOUT;
}

/*
 * Configure the FPGA for logic-analyzer mode.
 */
static int sigma_fpga_init_la(struct dev_context *devc)
{
        /* Initialize the logic analyzer mode. */
        uint8_t logic_mode_start[] = {
                REG_ADDR_LOW  | (READ_ID & 0xf),
                REG_ADDR_HIGH | (READ_ID >> 8),
                REG_READ_ADDR,  /* Read ID register. */

                REG_ADDR_LOW | (WRITE_TEST & 0xf),
                REG_DATA_LOW | 0x5,
                REG_DATA_HIGH_WRITE | 0x5,
                REG_READ_ADDR,  /* Read scratch register. */

                REG_DATA_LOW | 0xa,
                REG_DATA_HIGH_WRITE | 0xa,
                REG_READ_ADDR,  /* Read scratch register. */

                REG_ADDR_LOW | (WRITE_MODE & 0xf),
                REG_DATA_LOW | 0x0,
                REG_DATA_HIGH_WRITE | 0x8,
        };

        uint8_t result[3];
        int ret;

        /* Initialize the logic analyzer mode. */
        sigma_write(logic_mode_start, sizeof(logic_mode_start), devc);

        /* Expect a 3 byte reply since we issued three READ requests. */
        ret = sigma_read(result, 3, devc);
        if (ret != 3)
                goto err;

        if (result[0] != 0xa6 || result[1] != 0x55 || result[2] != 0xaa)
                goto err;

        return SR_OK;
err:
        sr_err("Configuration failed. Invalid reply received.");
        return SR_ERR;
}

/*
 * Read the firmware from a file and transform it into a series of bitbang
 * pulses used to program the FPGA. Note that the *bb_cmd must be free()'d
 * by the caller of this function.
 */
static int sigma_fw_2_bitbang(const char *filename,
                              uint8_t **bb_cmd, gsize *bb_cmd_size)
{
        GMappedFile *file;
        GError *error;
        gsize i, file_size, bb_size;
        gchar *firmware;
        uint8_t *bb_stream, *bbs;
        uint32_t imm;
        int bit, v;
        int ret = SR_OK;

        /*
         * Map the file and make the mapped buffer writable.
         * NOTE: Using writable=TRUE does _NOT_ mean that file that is mapped
         *       will be modified. It will not be modified until someone uses
         *       g_file_set_contents() on it.
         */
        error = NULL;
        file = g_mapped_file_new(filename, TRUE, &error);
        g_assert_no_error(error);

        file_size = g_mapped_file_get_length(file);
        firmware = g_mapped_file_get_contents(file);
        g_assert(firmware);

        /* Weird magic transformation below, I have no idea what it does. */
        imm = 0x3f6df2ab;
        for (i = 0; i < file_size; i++) {
                imm = (imm + 0xa853753) % 177 + (imm * 0x8034052);
                firmware[i] ^= imm & 0xff;
        }

        /*
         * Now that the firmware is "transformed", we will transcribe the
         * firmware blob into a sequence of toggles of the Dx wires. This
         * sequence will be fed directly into the Sigma, which must be in
         * the FPGA bitbang programming mode.
         */

        /* Each bit of firmware is transcribed as two toggles of Dx wires. */
        bb_size = file_size * 8 * 2;
        bb_stream = (uint8_t *)g_try_malloc(bb_size);
        if (!bb_stream) {
                sr_err("%s: Failed to allocate bitbang stream", __func__);
                ret = SR_ERR_MALLOC;
                goto exit;
        }

        bbs = bb_stream;
        for (i = 0; i < file_size; i++) {
                for (bit = 7; bit >= 0; bit--) {
                        v = (firmware[i] & (1 << bit)) ? 0x40 : 0x00;
                        *bbs++ = v | 0x01;
                        *bbs++ = v;
                }
        }

        /* The transformation completed successfully, return the result. */
        *bb_cmd = bb_stream;
        *bb_cmd_size = bb_size;

exit:
        g_mapped_file_unref(file);
        return ret;
}

static int upload_firmware(int firmware_idx, struct dev_context *devc)
{
        int ret;
        unsigned char *buf;
        unsigned char pins;
        size_t buf_size;
        const char *firmware = sigma_firmware_files[firmware_idx];
        struct ftdi_context *ftdic = &devc->ftdic;

        /* Make sure it's an ASIX SIGMA. */
        ret = ftdi_usb_open_desc(ftdic, USB_VENDOR, USB_PRODUCT,
                                 USB_DESCRIPTION, NULL);
        if (ret < 0) {
                sr_err("ftdi_usb_open failed: %s",
                       ftdi_get_error_string(ftdic));
                return 0;
        }

        ret = ftdi_set_bitmode(ftdic, 0xdf, BITMODE_BITBANG);
        if (ret < 0) {
                sr_err("ftdi_set_bitmode failed: %s",
                       ftdi_get_error_string(ftdic));
                return 0;
        }

        /* Four times the speed of sigmalogan - Works well. */
        ret = ftdi_set_baudrate(ftdic, 750000);
        if (ret < 0) {
                sr_err("ftdi_set_baudrate failed: %s",
                       ftdi_get_error_string(ftdic));
                return 0;
        }

        /* Initialize the FPGA for firmware upload. */
        ret = sigma_fpga_init_bitbang(devc);
        if (ret)
                return ret;

        /* Prepare firmware. */
        ret = sigma_fw_2_bitbang(firmware, &buf, &buf_size);
        if (ret != SR_OK) {
                sr_err("An error occured while reading the firmware: %s",
                       firmware);
                return ret;
        }

        /* Upload firmare. */
        sr_info("Uploading firmware file '%s'.", firmware);
        sigma_write(buf, buf_size, devc);

        g_free(buf);

        ret = ftdi_set_bitmode(ftdic, 0x00, BITMODE_RESET);
        if (ret < 0) {
                sr_err("ftdi_set_bitmode failed: %s",
                       ftdi_get_error_string(ftdic));
                return SR_ERR;
        }

        ftdi_usb_purge_buffers(ftdic);

        /* Discard garbage. */
        while (sigma_read(&pins, 1, devc) == 1)
                ;

        /* Initialize the FPGA for logic-analyzer mode. */
        ret = sigma_fpga_init_la(devc);
        if (ret != SR_OK)
                return ret;

        devc->cur_firmware = firmware_idx;

        sr_info("Firmware uploaded.");

        return SR_OK;
}

static int dev_open(struct sr_dev_inst *sdi)
{
        struct dev_context *devc;
        int ret;

        devc = sdi->priv;

        /* Make sure it's an ASIX SIGMA. */
        if ((ret = ftdi_usb_open_desc(&devc->ftdic,
                USB_VENDOR, USB_PRODUCT, USB_DESCRIPTION, NULL)) < 0) {

                sr_err("ftdi_usb_open failed: %s",
                       ftdi_get_error_string(&devc->ftdic));

                return 0;
        }

        sdi->status = SR_ST_ACTIVE;

        return SR_OK;
}

static int set_samplerate(const struct sr_dev_inst *sdi, uint64_t samplerate)
{
        struct dev_context *devc;
        unsigned int i;
        int ret;

        devc = sdi->priv;
        ret = SR_OK;

        for (i = 0; i < ARRAY_SIZE(samplerates); i++) {
                if (samplerates[i] == samplerate)
                        break;
        }
        if (samplerates[i] == 0)
                return SR_ERR_SAMPLERATE;

        if (samplerate <= SR_MHZ(50)) {
                ret = upload_firmware(0, devc);
                devc->num_channels = 16;
        } else if (samplerate == SR_MHZ(100)) {
                ret = upload_firmware(1, devc);
                devc->num_channels = 8;
        } else if (samplerate == SR_MHZ(200)) {
                ret = upload_firmware(2, devc);
                devc->num_channels = 4;
        }

        if (ret == SR_OK) {
                devc->cur_samplerate = samplerate;
                devc->period_ps = 1000000000000ULL / samplerate;
                devc->samples_per_event = 16 / devc->num_channels;
                devc->state.state = SIGMA_IDLE;
        }

        return ret;
}

/*
 * In 100 and 200 MHz mode, only a single pin rising/falling can be
 * set as trigger. In other modes, two rising/falling triggers can be set,
 * in addition to value/mask trigger for any number of channels.
 *
 * The Sigma supports complex triggers using boolean expressions, but this
 * has not been implemented yet.
 */
static int convert_trigger(const struct sr_dev_inst *sdi)
{
        struct dev_context *devc;
        struct sr_trigger *trigger;
        struct sr_trigger_stage *stage;
        struct sr_trigger_match *match;
        const GSList *l, *m;
        int channelbit, trigger_set;

        devc = sdi->priv;
        memset(&devc->trigger, 0, sizeof(struct sigma_trigger));
        if (!(trigger = sr_session_trigger_get(sdi->session)))
                return SR_OK;

        trigger_set = 0;
        for (l = trigger->stages; l; l = l->next) {
                stage = l->data;
                for (m = stage->matches; m; m = m->next) {
                        match = m->data;
                        if (!match->channel->enabled)
                                /* Ignore disabled channels with a trigger. */
                                continue;
                        channelbit = 1 << (match->channel->index);
                        if (devc->cur_samplerate >= SR_MHZ(100)) {
                                /* Fast trigger support. */
                                if (trigger_set) {
                                        sr_err("Only a single pin trigger is "
                                                        "supported in 100 and 200MHz mode.");
                                        return SR_ERR;
                                }
                                if (match->match == SR_TRIGGER_FALLING)
                                        devc->trigger.fallingmask |= channelbit;
                                else if (match->match == SR_TRIGGER_RISING)
                                        devc->trigger.risingmask |= channelbit;
                                else {
                                        sr_err("Only rising/falling trigger is "
                                                        "supported in 100 and 200MHz mode.");
                                        return SR_ERR;
                                }

                                ++trigger_set;
                        } else {
                                /* Simple trigger support (event). */
                                if (match->match == SR_TRIGGER_ONE) {
                                        devc->trigger.simplevalue |= channelbit;
                                        devc->trigger.simplemask |= channelbit;
                                }
                                else if (match->match == SR_TRIGGER_ZERO) {
                                        devc->trigger.simplevalue &= ~channelbit;
                                        devc->trigger.simplemask |= channelbit;
                                }
                                else if (match->match == SR_TRIGGER_FALLING) {
                                        devc->trigger.fallingmask |= channelbit;
                                        ++trigger_set;
                                }
                                else if (match->match == SR_TRIGGER_RISING) {
                                        devc->trigger.risingmask |= channelbit;
                                        ++trigger_set;
                                }

                                /*
                                 * Actually, Sigma supports 2 rising/falling triggers,
                                 * but they are ORed and the current trigger syntax
                                 * does not permit ORed triggers.
                                 */
                                if (trigger_set > 1) {
                                        sr_err("Only 1 rising/falling trigger "
                                                   "is supported.");
                                        return SR_ERR;
                                }
                        }
                }
        }


        return SR_OK;
}

static int dev_close(struct sr_dev_inst *sdi)
{
        struct dev_context *devc;

        devc = sdi->priv;

        /* TODO */
        if (sdi->status == SR_ST_ACTIVE)
                ftdi_usb_close(&devc->ftdic);

        sdi->status = SR_ST_INACTIVE;

        return SR_OK;
}

static int cleanup(const struct sr_dev_driver *di)
{
        return dev_clear(di);
}

static int config_get(uint32_t key, GVariant **data, const struct sr_dev_inst *sdi,
                const struct sr_channel_group *cg)
{
        struct dev_context *devc;

        (void)cg;

        if (!sdi)
                return SR_ERR;
        devc = sdi->priv;

        switch (key) {
        case SR_CONF_SAMPLERATE:
                *data = g_variant_new_uint64(devc->cur_samplerate);
                break;
        case SR_CONF_LIMIT_MSEC:
                *data = g_variant_new_uint64(devc->limit_msec);
                break;
        case SR_CONF_CAPTURE_RATIO:
                *data = g_variant_new_uint64(devc->capture_ratio);
                break;
        default:
                return SR_ERR_NA;
        }

        return SR_OK;
}

static int config_set(uint32_t key, GVariant *data, const struct sr_dev_inst *sdi,
                const struct sr_channel_group *cg)
{
        struct dev_context *devc;
        uint64_t tmp;
        int ret;

        (void)cg;

        if (sdi->status != SR_ST_ACTIVE)
                return SR_ERR_DEV_CLOSED;

        devc = sdi->priv;

        ret = SR_OK;
        switch (key) {
        case SR_CONF_SAMPLERATE:
                ret = set_samplerate(sdi, g_variant_get_uint64(data));
                break;
        case SR_CONF_LIMIT_MSEC:
                tmp = g_variant_get_uint64(data);
                if (tmp > 0)
                        devc->limit_msec = g_variant_get_uint64(data);
                else
                        ret = SR_ERR;
                break;
        case SR_CONF_LIMIT_SAMPLES:
                tmp = g_variant_get_uint64(data);
                devc->limit_msec = tmp * 1000 / devc->cur_samplerate;
                break;
        case SR_CONF_CAPTURE_RATIO:
                tmp = g_variant_get_uint64(data);
                if (tmp <= 100)
                        devc->capture_ratio = tmp;
                else
                        ret = SR_ERR;
                break;
        default:
                ret = SR_ERR_NA;
        }

        return ret;
}

static int config_list(uint32_t key, GVariant **data, const struct sr_dev_inst *sdi,
                const struct sr_channel_group *cg)
{
        GVariant *gvar;
        GVariantBuilder gvb;

        (void)sdi;
        (void)cg;

        switch (key) {
        case SR_CONF_DEVICE_OPTIONS:
                if (!sdi)
                        *data = g_variant_new_fixed_array(G_VARIANT_TYPE_UINT32,
                                        drvopts, ARRAY_SIZE(drvopts), sizeof(uint32_t));
                else
                        *data = g_variant_new_fixed_array(G_VARIANT_TYPE_UINT32,
                                        devopts, ARRAY_SIZE(devopts), sizeof(uint32_t));
                break;
        case SR_CONF_SAMPLERATE:
                g_variant_builder_init(&gvb, G_VARIANT_TYPE("a{sv}"));
                gvar = g_variant_new_fixed_array(G_VARIANT_TYPE("t"), samplerates,
                                ARRAY_SIZE(samplerates), sizeof(uint64_t));
                g_variant_builder_add(&gvb, "{sv}", "samplerates", gvar);
                *data = g_variant_builder_end(&gvb);
                break;
        case SR_CONF_TRIGGER_MATCH:
                *data = g_variant_new_fixed_array(G_VARIANT_TYPE_INT32,
                                trigger_matches, ARRAY_SIZE(trigger_matches),
                                sizeof(int32_t));
                break;
        default:
                return SR_ERR_NA;
        }

        return SR_OK;
}

/* Software trigger to determine exact trigger position. */
static int get_trigger_offset(uint8_t *samples, uint16_t last_sample,
                              struct sigma_trigger *t)
{
        int i;
        uint16_t sample = 0;

        for (i = 0; i < 8; ++i) {
                if (i > 0)
                        last_sample = sample;
                sample = samples[2 * i] | (samples[2 * i + 1] << 8);

                /* Simple triggers. */
                if ((sample & t->simplemask) != t->simplevalue)
                        continue;

                /* Rising edge. */
                if (((last_sample & t->risingmask) != 0) ||
                    ((sample & t->risingmask) != t->risingmask))
                        continue;

                /* Falling edge. */
                if ((last_sample & t->fallingmask) != t->fallingmask ||
                    (sample & t->fallingmask) != 0)
                        continue;

                break;
        }

        /* If we did not match, return original trigger pos. */
        return i & 0x7;
}


/*
 * Return the timestamp of "DRAM cluster".
 */
static uint16_t sigma_dram_cluster_ts(struct sigma_dram_cluster *cluster)
{
        return (cluster->timestamp_hi << 8) | cluster->timestamp_lo;
}

static void sigma_decode_dram_cluster(struct sigma_dram_cluster *dram_cluster,
                                      unsigned int events_in_cluster,
                                      unsigned int triggered,
                                      struct sr_dev_inst *sdi)
{
        struct dev_context *devc = sdi->priv;
        struct sigma_state *ss = &devc->state;
        struct sr_datafeed_packet packet;
        struct sr_datafeed_logic logic;
        uint16_t tsdiff, ts;
        uint8_t samples[2048];
        unsigned int i;

        ts = sigma_dram_cluster_ts(dram_cluster);
        tsdiff = ts - ss->lastts;
        ss->lastts = ts;

        packet.type = SR_DF_LOGIC;
        packet.payload = &logic;
        logic.unitsize = 2;
        logic.data = samples;

        /*
         * First of all, send Sigrok a copy of the last sample from
         * previous cluster as many times as needed to make up for
         * the differential characteristics of data we get from the
         * Sigma. Sigrok needs one sample of data per period.
         *
         * One DRAM cluster contains a timestamp and seven samples,
         * the units of timestamp are "devc->period_ps" , the first
         * sample in the cluster happens at the time of the timestamp
         * and the remaining samples happen at timestamp +1...+6 .
         */
        for (ts = 0; ts < tsdiff - (EVENTS_PER_CLUSTER - 1); ts++) {
                i = ts % 1024;
                samples[2 * i + 0] = ss->lastsample & 0xff;
                samples[2 * i + 1] = ss->lastsample >> 8;

                /*
                 * If we have 1024 samples ready or we're at the
                 * end of submitting the padding samples, submit
                 * the packet to Sigrok.
                 */
                if ((i == 1023) || (ts == (tsdiff - EVENTS_PER_CLUSTER))) {
                        logic.length = (i + 1) * logic.unitsize;
                        sr_session_send(sdi, &packet);
                }
        }

        /*
         * Parse the samples in current cluster and prepare them
         * to be submitted to Sigrok.
         */
        for (i = 0; i < events_in_cluster; i++) {
                samples[2 * i + 1] = dram_cluster->samples[i].sample_lo;
                samples[2 * i + 0] = dram_cluster->samples[i].sample_hi;
        }

        /* Send data up to trigger point (if triggered). */
        int trigger_offset = 0;
        if (triggered) {
                /*
                 * Trigger is not always accurate to sample because of
                 * pipeline delay. However, it always triggers before
                 * the actual event. We therefore look at the next
                 * samples to pinpoint the exact position of the trigger.
                 */
                trigger_offset = get_trigger_offset(samples,
                                        ss->lastsample, &devc->trigger);

                if (trigger_offset > 0) {
                        packet.type = SR_DF_LOGIC;
                        logic.length = trigger_offset * logic.unitsize;
                        sr_session_send(sdi, &packet);
                        events_in_cluster -= trigger_offset;
                }

                /* Only send trigger if explicitly enabled. */
                if (devc->use_triggers) {
                        packet.type = SR_DF_TRIGGER;
                        sr_session_send(sdi, &packet);
                }
        }

        if (events_in_cluster > 0) {
                packet.type = SR_DF_LOGIC;
                logic.length = events_in_cluster * logic.unitsize;
                logic.data = samples + (trigger_offset * logic.unitsize);
                sr_session_send(sdi, &packet);
        }

        ss->lastsample =
                samples[2 * (events_in_cluster - 1) + 0] |
                (samples[2 * (events_in_cluster - 1) + 1] << 8);

}

/*
 * Decode chunk of 1024 bytes, 64 clusters, 7 events per cluster.
 * Each event is 20ns apart, and can contain multiple samples.
 *
 * For 200 MHz, events contain 4 samples for each channel, spread 5 ns apart.
 * For 100 MHz, events contain 2 samples for each channel, spread 10 ns apart.
 * For 50 MHz and below, events contain one sample for each channel,
 * spread 20 ns apart.
 */
static int decode_chunk_ts(struct sigma_dram_line *dram_line,
                           uint16_t events_in_line,
                           uint32_t trigger_event,
                           struct sr_dev_inst *sdi)
{
        struct sigma_dram_cluster *dram_cluster;
        struct dev_context *devc = sdi->priv;
        unsigned int clusters_in_line =
                (events_in_line + (EVENTS_PER_CLUSTER - 1)) / EVENTS_PER_CLUSTER;
        unsigned int events_in_cluster;
        unsigned int i;
        uint32_t trigger_cluster = ~0, triggered = 0;

        /* Check if trigger is in this chunk. */
        if (trigger_event < (64 * 7)) {
                if (devc->cur_samplerate <= SR_MHZ(50)) {
                        trigger_event -= MIN(EVENTS_PER_CLUSTER - 1,
                                             trigger_event);
                }

                /* Find in which cluster the trigger occured. */
                trigger_cluster = trigger_event / EVENTS_PER_CLUSTER;
        }

        /* For each full DRAM cluster. */
        for (i = 0; i < clusters_in_line; i++) {
                dram_cluster = &dram_line->cluster[i];

                /* The last cluster might not be full. */
                if ((i == clusters_in_line - 1) &&
                    (events_in_line % EVENTS_PER_CLUSTER)) {
                        events_in_cluster = events_in_line % EVENTS_PER_CLUSTER;
                } else {
                        events_in_cluster = EVENTS_PER_CLUSTER;
                }

                triggered = (i == trigger_cluster);
                sigma_decode_dram_cluster(dram_cluster, events_in_cluster,
                                          triggered, sdi);
        }

        return SR_OK;
}

static int download_capture(struct sr_dev_inst *sdi)
{
        struct dev_context *devc = sdi->priv;
        const uint32_t chunks_per_read = 32;
        struct sigma_dram_line *dram_line;
        int bufsz;
        uint32_t stoppos, triggerpos;
        struct sr_datafeed_packet packet;
        uint8_t modestatus;

        uint32_t i;
        uint32_t dl_lines_total, dl_lines_curr, dl_lines_done;
        uint32_t dl_events_in_line = 64 * 7;
        uint32_t trg_line = ~0, trg_event = ~0;

        dram_line = g_try_malloc0(chunks_per_read * sizeof(*dram_line));
        if (!dram_line)
                return FALSE;

        sr_info("Downloading sample data.");

        /* Stop acquisition. */
        sigma_set_register(WRITE_MODE, 0x11, devc);

        /* Set SDRAM Read Enable. */
        sigma_set_register(WRITE_MODE, 0x02, devc);

        /* Get the current position. */
        sigma_read_pos(&stoppos, &triggerpos, devc);

        /* Check if trigger has fired. */
        modestatus = sigma_get_register(READ_MODE, devc);
        if (modestatus & 0x20) {
                trg_line = triggerpos >> 9;
                trg_event = triggerpos & 0x1ff;
        }

        /*
         * Determine how many 1024b "DRAM lines" do we need to read from the
         * Sigma so we have a complete set of samples. Note that the last
         * line can be only partial, containing less than 64 clusters.
         */
        dl_lines_total = (stoppos >> 9) + 1;

        dl_lines_done = 0;

        while (dl_lines_total > dl_lines_done) {
                /* We can download only up-to 32 DRAM lines in one go! */
                dl_lines_curr = MIN(chunks_per_read, dl_lines_total);

                bufsz = sigma_read_dram(dl_lines_done, dl_lines_curr,
                                        (uint8_t *)dram_line, devc);
                /* TODO: Check bufsz. For now, just avoid compiler warnings. */
                (void)bufsz;

                /* This is the first DRAM line, so find the initial timestamp. */
                if (dl_lines_done == 0) {
                        devc->state.lastts =
                                sigma_dram_cluster_ts(&dram_line[0].cluster[0]);
                        devc->state.lastsample = 0;
                }

                for (i = 0; i < dl_lines_curr; i++) {
                        uint32_t trigger_event = ~0;
                        /* The last "DRAM line" can be only partially full. */
                        if (dl_lines_done + i == dl_lines_total - 1)
                                dl_events_in_line = stoppos & 0x1ff;

                        /* Test if the trigger happened on this line. */
                        if (dl_lines_done + i == trg_line)
                                trigger_event = trg_event;

                        decode_chunk_ts(dram_line + i, dl_events_in_line,
                                        trigger_event, sdi);
                }

                dl_lines_done += dl_lines_curr;
        }

        /* All done. */
        packet.type = SR_DF_END;
        sr_session_send(sdi, &packet);

        dev_acquisition_stop(sdi, sdi);

        g_free(dram_line);

        return TRUE;
}

/*
 * Handle the Sigma when in CAPTURE mode. This function checks:
 * - Sampling time ended
 * - DRAM capacity overflow
 * This function triggers download of the samples from Sigma
 * in case either of the above conditions is true.
 */
static int sigma_capture_mode(struct sr_dev_inst *sdi)
{
        struct dev_context *devc = sdi->priv;

        uint64_t running_msec;
        struct timeval tv;

        uint32_t stoppos, triggerpos;

        /* Check if the selected sampling duration passed. */
        gettimeofday(&tv, 0);
        running_msec = (tv.tv_sec - devc->start_tv.tv_sec) * 1000 +
                       (tv.tv_usec - devc->start_tv.tv_usec) / 1000;
        if (running_msec >= devc->limit_msec)
                return download_capture(sdi);

        /* Get the position in DRAM to which the FPGA is writing now. */
        sigma_read_pos(&stoppos, &triggerpos, devc);
        /* Test if DRAM is full and if so, download the data. */
        if ((stoppos >> 9) == 32767)
                return download_capture(sdi);

        return TRUE;
}

static int receive_data(int fd, int revents, void *cb_data)
{
        struct sr_dev_inst *sdi;
        struct dev_context *devc;

        (void)fd;
        (void)revents;

        sdi = cb_data;
        devc = sdi->priv;

        if (devc->state.state == SIGMA_IDLE)
                return TRUE;

        if (devc->state.state == SIGMA_CAPTURE)
                return sigma_capture_mode(sdi);

        return TRUE;
}

/* Build a LUT entry used by the trigger functions. */
static void build_lut_entry(uint16_t value, uint16_t mask, uint16_t *entry)
{
        int i, j, k, bit;

        /* For each quad channel. */
        for (i = 0; i < 4; ++i) {
                entry[i] = 0xffff;

                /* For each bit in LUT. */
                for (j = 0; j < 16; ++j)

                        /* For each channel in quad. */
                        for (k = 0; k < 4; ++k) {
                                bit = 1 << (i * 4 + k);

                                /* Set bit in entry */
                                if ((mask & bit) &&
                                    ((!(value & bit)) !=
                                    (!(j & (1 << k)))))
                                        entry[i] &= ~(1 << j);
                        }
        }
}

/* Add a logical function to LUT mask. */
static void add_trigger_function(enum triggerop oper, enum triggerfunc func,
                                 int index, int neg, uint16_t *mask)
{
        int i, j;
        int x[2][2], tmp, a, b, aset, bset, rset;

        memset(x, 0, 4 * sizeof(int));

        /* Trigger detect condition. */
        switch (oper) {
        case OP_LEVEL:
                x[0][1] = 1;
                x[1][1] = 1;
                break;
        case OP_NOT:
                x[0][0] = 1;
                x[1][0] = 1;
                break;
        case OP_RISE:
                x[0][1] = 1;
                break;
        case OP_FALL:
                x[1][0] = 1;
                break;
        case OP_RISEFALL:
                x[0][1] = 1;
                x[1][0] = 1;
                break;
        case OP_NOTRISE:
                x[1][1] = 1;
                x[0][0] = 1;
                x[1][0] = 1;
                break;
        case OP_NOTFALL:
                x[1][1] = 1;
                x[0][0] = 1;
                x[0][1] = 1;
                break;
        case OP_NOTRISEFALL:
                x[1][1] = 1;
                x[0][0] = 1;
                break;
        }

        /* Transpose if neg is set. */
        if (neg) {
                for (i = 0; i < 2; ++i) {
                        for (j = 0; j < 2; ++j) {
                                tmp = x[i][j];
                                x[i][j] = x[1-i][1-j];
                                x[1-i][1-j] = tmp;
                        }
                }
        }

        /* Update mask with function. */
        for (i = 0; i < 16; ++i) {
                a = (i >> (2 * index + 0)) & 1;
                b = (i >> (2 * index + 1)) & 1;

                aset = (*mask >> i) & 1;
                bset = x[b][a];

                rset = 0;
                if (func == FUNC_AND || func == FUNC_NAND)
                        rset = aset & bset;
                else if (func == FUNC_OR || func == FUNC_NOR)
                        rset = aset | bset;
                else if (func == FUNC_XOR || func == FUNC_NXOR)
                        rset = aset ^ bset;

                if (func == FUNC_NAND || func == FUNC_NOR || func == FUNC_NXOR)
                        rset = !rset;

                *mask &= ~(1 << i);

                if (rset)
                        *mask |= 1 << i;
        }
}

/*
 * Build trigger LUTs used by 50 MHz and lower sample rates for supporting
 * simple pin change and state triggers. Only two transitions (rise/fall) can be
 * set at any time, but a full mask and value can be set (0/1).
 */
static int build_basic_trigger(struct triggerlut *lut, struct dev_context *devc)
{
        int i,j;
        uint16_t masks[2] = { 0, 0 };

        memset(lut, 0, sizeof(struct triggerlut));

        /* Contant for simple triggers. */
        lut->m4 = 0xa000;

        /* Value/mask trigger support. */
        build_lut_entry(devc->trigger.simplevalue, devc->trigger.simplemask,
                        lut->m2d);

        /* Rise/fall trigger support. */
        for (i = 0, j = 0; i < 16; ++i) {
                if (devc->trigger.risingmask & (1 << i) ||
                    devc->trigger.fallingmask & (1 << i))
                        masks[j++] = 1 << i;
        }

        build_lut_entry(masks[0], masks[0], lut->m0d);
        build_lut_entry(masks[1], masks[1], lut->m1d);

        /* Add glue logic */
        if (masks[0] || masks[1]) {
                /* Transition trigger. */
                if (masks[0] & devc->trigger.risingmask)
                        add_trigger_function(OP_RISE, FUNC_OR, 0, 0, &lut->m3);
                if (masks[0] & devc->trigger.fallingmask)
                        add_trigger_function(OP_FALL, FUNC_OR, 0, 0, &lut->m3);
                if (masks[1] & devc->trigger.risingmask)
                        add_trigger_function(OP_RISE, FUNC_OR, 1, 0, &lut->m3);
                if (masks[1] & devc->trigger.fallingmask)
                        add_trigger_function(OP_FALL, FUNC_OR, 1, 0, &lut->m3);
        } else {
                /* Only value/mask trigger. */
                lut->m3 = 0xffff;
        }

        /* Triggertype: event. */
        lut->params.selres = 3;

        return SR_OK;
}

static int dev_acquisition_start(const struct sr_dev_inst *sdi, void *cb_data)
{
        struct dev_context *devc;
        struct clockselect_50 clockselect;
        int frac, triggerpin, ret;
        uint8_t triggerselect = 0;
        struct triggerinout triggerinout_conf;
        struct triggerlut lut;

        if (sdi->status != SR_ST_ACTIVE)
                return SR_ERR_DEV_CLOSED;

        devc = sdi->priv;

        if (convert_trigger(sdi) != SR_OK) {
                sr_err("Failed to configure triggers.");
                return SR_ERR;
        }

        /* If the samplerate has not been set, default to 200 kHz. */
        if (devc->cur_firmware == -1) {
                if ((ret = set_samplerate(sdi, SR_KHZ(200))) != SR_OK)
                        return ret;
        }

        /* Enter trigger programming mode. */
        sigma_set_register(WRITE_TRIGGER_SELECT1, 0x20, devc);

        /* 100 and 200 MHz mode. */
        if (devc->cur_samplerate >= SR_MHZ(100)) {
                sigma_set_register(WRITE_TRIGGER_SELECT1, 0x81, devc);

                /* Find which pin to trigger on from mask. */
                for (triggerpin = 0; triggerpin < 8; ++triggerpin)
                        if ((devc->trigger.risingmask | devc->trigger.fallingmask) &
                            (1 << triggerpin))
                                break;

                /* Set trigger pin and light LED on trigger. */
                triggerselect = (1 << LEDSEL1) | (triggerpin & 0x7);

                /* Default rising edge. */
                if (devc->trigger.fallingmask)
                        triggerselect |= 1 << 3;

        /* All other modes. */
        } else if (devc->cur_samplerate <= SR_MHZ(50)) {
                build_basic_trigger(&lut, devc);

                sigma_write_trigger_lut(&lut, devc);

                triggerselect = (1 << LEDSEL1) | (1 << LEDSEL0);
        }

        /* Setup trigger in and out pins to default values. */
        memset(&triggerinout_conf, 0, sizeof(struct triggerinout));
        triggerinout_conf.trgout_bytrigger = 1;
        triggerinout_conf.trgout_enable = 1;

        sigma_write_register(WRITE_TRIGGER_OPTION,
                             (uint8_t *) &triggerinout_conf,
                             sizeof(struct triggerinout), devc);

        /* Go back to normal mode. */
        sigma_set_register(WRITE_TRIGGER_SELECT1, triggerselect, devc);

        /* Set clock select register. */
        if (devc->cur_samplerate == SR_MHZ(200))
                /* Enable 4 channels. */
                sigma_set_register(WRITE_CLOCK_SELECT, 0xf0, devc);
        else if (devc->cur_samplerate == SR_MHZ(100))
                /* Enable 8 channels. */
                sigma_set_register(WRITE_CLOCK_SELECT, 0x00, devc);
        else {
                /*
                 * 50 MHz mode (or fraction thereof). Any fraction down to
                 * 50 MHz / 256 can be used, but is not supported by sigrok API.
                 */
                frac = SR_MHZ(50) / devc->cur_samplerate - 1;

                clockselect.async = 0;
                clockselect.fraction = frac;
                clockselect.disabled_channels = 0;

                sigma_write_register(WRITE_CLOCK_SELECT,
                                     (uint8_t *) &clockselect,
                                     sizeof(clockselect), devc);
        }

        /* Setup maximum post trigger time. */
        sigma_set_register(WRITE_POST_TRIGGER,
                           (devc->capture_ratio * 255) / 100, devc);

        /* Start acqusition. */
        gettimeofday(&devc->start_tv, 0);
        sigma_set_register(WRITE_MODE, 0x0d, devc);

        devc->cb_data = cb_data;

        /* Send header packet to the session bus. */
        std_session_send_df_header(sdi, LOG_PREFIX);

        /* Add capture source. */
        sr_session_source_add(sdi->session, 0, G_IO_IN, 10, receive_data, (void *)sdi);

        devc->state.state = SIGMA_CAPTURE;

        return SR_OK;
}

static int dev_acquisition_stop(struct sr_dev_inst *sdi, void *cb_data)
{
        struct dev_context *devc;

        (void)cb_data;

        devc = sdi->priv;
        devc->state.state = SIGMA_IDLE;

        sr_session_source_remove(sdi->session, 0);

        return SR_OK;
}

SR_PRIV struct sr_dev_driver asix_sigma_driver_info = {
        .name = "asix-sigma",
        .longname = "ASIX SIGMA/SIGMA2",
        .api_version = 1,
        .init = init,
        .cleanup = cleanup,
        .scan = scan,
        .dev_list = dev_list,
        .dev_clear = dev_clear,
        .config_get = config_get,
        .config_set = config_set,
        .config_list = config_list,
        .dev_open = dev_open,
        .dev_close = dev_close,
        .dev_acquisition_start = dev_acquisition_start,
        .dev_acquisition_stop = dev_acquisition_stop,
        .priv = NULL,
};