Add nrf24l01 unit test dump.

[sigrok-dumps.git] / spi / mx25l1605d / README

diff --git a/spi/mx25l1605d/README b/spi/mx25l1605d/README
index ade54066241bbe305402c8c56add543342d49a83..920ae313a1643f9909e937fe8d18572296a82604 100644 (file)
--- a/spi/mx25l1605d/README
+++ b/spi/mx25l1605d/README
@@ -18,20 +18,16 @@ The software used for programming it is flashrom, see
 Logic analyzer setup
 --------------------
 
-The logic analyzer used for capturing is a ChronoVu LA8 at a sample rate
-of 25MHz.
+The logic analyzer used was a ChronoVu LA8 (at 25MHz):
 
-The ChronoVu LA8 probes were connected to the MX25L1605D chip like this:
-
-  Probe       SPI chip pin
-  ------------------------
+  Probe       MX25L1605D pin
+  --------------------------
   0 (green)   CS#
   1 (orange)  SO/SIO1 (a.k.a MISO)
   2 (white)   SCLK
   3 (red)     SI/SIO0 (a.k.a MOSI)
   4 (gray)    WP#/ACC
   5 (brown)   HOLD#
-  GND         GND
 
 
 Probing
@@ -46,7 +42,7 @@ The sigrok command line used was:
   sigrok-cli -d 0:samplerate=25mhz --samples 8388608 \
              -p '1=CS#,2=MISO,3=SCLK,4=MOSI,5=WP#,6=HOLD#' \
              --wait-trigger --triggers 3=1 \
-             -o mx25l1605d_probe.sigrok
+             -o mx25l1605d_probe.sr
 
 The capturing starts when the SCLK signal is high for the first time
 (it's low per default). We capture as many samples as fit into the 8MByte
@@ -69,7 +65,7 @@ The sigrok command line used was:
 
   sigrok-cli -d 0:samplerate=25mhz --samples 8388608 \
              -p '1=CS#,2=MISO,3=SCLK,4=MOSI,5=WP#,6=HOLD#' \
-             -o mx25l1605d_write_hello_world.sigrok
+             -o mx25l1605d_write.sr
 
 The capture is only partial, it contains a small part of the write process
 (it does not contain the chip identification, chip erase, etc. which comes
@@ -88,7 +84,7 @@ The sigrok command line used was:
 
   sigrok-cli -d 0:samplerate=25mhz --samples 8388608 \
              -p '1=CS#,2=MISO,3=SCLK,4=MOSI,5=WP#,6=HOLD#' \
-             -o mx25l1605d_read.sigrok
+             -o mx25l1605d_read.sr
 
 The capture only contains a small part of the read procedure. The data in
 the chip consists of consecutive "HelloWorld" ASCII strings.
@@ -105,7 +101,7 @@ The sigrok command line used was:
 
   sigrok-cli -d 0:samplerate=25mhz --samples 8388608 \
              -p '1=CS#,2=MISO,3=SCLK,4=MOSI,5=WP#,6=HOLD#' \
-             -o mx25l1605d_erase.sigrok
+             -o mx25l1605d_erase.sr
 
 The capture does not contain the full erase process, only a small part of it.