Difference between revisions of "PeakTech 3415"

From sigrok
Jump to navigation Jump to search
(link from device page to info page with lsusb output)
 
Line 14: Line 14:


The device uses the [[Multimeter_ICs#Dream_Tech_International_DTM0660|Dream Tech International DTM0660]] as main IC.
The device uses the [[Multimeter_ICs#Dream_Tech_International_DTM0660|Dream Tech International DTM0660]] as main IC.
See [[PeakTech 3415/Info]] for more details (such as '''lsusb -v''' output) about the device.


== Hardware ==
== Hardware ==
Line 33: Line 35:


To enable output to the PC on the multimeter you have to long-press the '''REL''' key. However, it will auto-poweroff even in this mode. To avoid that, press '''SELECT''' key during power-up (see manual).
To enable output to the PC on the multimeter you have to long-press the '''REL''' key. However, it will auto-poweroff even in this mode. To avoid that, press '''SELECT''' key during power-up (see manual).
== Logs ==
<small>
$ sudo lsusb -v
...
Bus 002 Device 008: ID 067b:2303 Prolific Technology, Inc. PL2303 Serial Port
Device Descriptor:
  bLength                18
  bDescriptorType        1
  bcdUSB              2.00
  bDeviceClass            0 (Defined at Interface level)
  bDeviceSubClass        0
  bDeviceProtocol        0
  bMaxPacketSize0        64
  idVendor          0x067b Prolific Technology, Inc.
  idProduct          0x2303 PL2303 Serial Port
  bcdDevice            3.00
  iManufacturer          1 Prolific Technology Inc.
  iProduct                2 USB-Serial Controller
  iSerial                0
  bNumConfigurations      1
  Configuration Descriptor:
    bLength                9
    bDescriptorType        2
    wTotalLength          39
    bNumInterfaces          1
    bConfigurationValue    1
    iConfiguration          0
    bmAttributes        0xa0
      (Bus Powered)
      Remote Wakeup
    MaxPower              100mA
    Interface Descriptor:
      bLength                9
      bDescriptorType        4
      bInterfaceNumber        0
      bAlternateSetting      0
      bNumEndpoints          3
      bInterfaceClass      255 Vendor Specific Class
      bInterfaceSubClass      0
      bInterfaceProtocol      0
      iInterface              0
      Endpoint Descriptor:
        bLength                7
        bDescriptorType        5
        bEndpointAddress    0x81  EP 1 IN
        bmAttributes            3
          Transfer Type            Interrupt
          Synch Type              None
          Usage Type              Data
        wMaxPacketSize    0x000a  1x 10 bytes
        bInterval              1
      Endpoint Descriptor:
        bLength                7
        bDescriptorType        5
        bEndpointAddress    0x02  EP 2 OUT
        bmAttributes            2
          Transfer Type            Bulk
          Synch Type              None
          Usage Type              Data
        wMaxPacketSize    0x0040  1x 64 bytes
        bInterval              0
      Endpoint Descriptor:
        bLength                7
        bDescriptorType        5
        bEndpointAddress    0x83  EP 3 IN
        bmAttributes            2
          Transfer Type            Bulk
          Synch Type              None
          Usage Type              Data
        wMaxPacketSize    0x0040  1x 64 bytes
        bInterval              0
Device Status:    0x0000
  (Bus Powered)
...
</small>


== Resources ==
== Resources ==

Latest revision as of 19:31, 3 September 2018

PeakTech 3415
Peaktech3415 top.png
Status supported
Source code serial-dmm
Counts 6000
IEC 61010-1 CAT III (1000V) / CAT IV (600V)
Measurements voltage, current, resistance, capacitance, frequency, temperature, duty cycle, diode, continuity
Features autorange, data hold, relative, min/max, backlight
Website peaktech.de

The Peaktech is a handheld digital multimeter with USB connectivity.

The device uses the Dream Tech International DTM0660 as main IC.

See PeakTech 3415/Info for more details (such as lsusb -v output) about the device.

Hardware

Multimeter:

Photos

  • Device, front

  • PCB exposed, bottom side

  • Infrared-USB Adapter Cable

  • Device, in use

Protocol

To enable output to the PC on the multimeter you have to long-press the REL key. However, it will auto-poweroff even in this mode. To avoid that, press SELECT key during power-up (see manual).

Resources

Retrieved from "https://sigrok.org/w/index.php?title=PeakTech_3415&oldid=13641"