Difference between revisions of "BENNING MM 12"
(Review and Test section) |
|||
| Line 22: | Line 22: | ||
* ADC: [http://www.cyrustek.com.tw/spec/ES51966A.pdf CYRUSTEK ES51966] | * ADC: [http://www.cyrustek.com.tw/spec/ES51966A.pdf CYRUSTEK ES51966] | ||
= Photos and Teardown = | |||
<gallery> | <gallery> | ||
| Line 51: | Line 51: | ||
</gallery> | </gallery> | ||
= Review and Test = | |||
== Usage of rechargable NiMH batteries == | |||
The device works quite well with rechargable batteries. Voltage boundaries are well selected to suit the needs of both Alkaline and NiMH cells. For NiMH the reported battery level is of course to low. | The device works quite well with rechargable batteries. Voltage boundaries are well selected to suit the needs of both Alkaline and NiMH cells. For NiMH the reported battery level is of course to low. | ||
| Line 66: | Line 66: | ||
The cut-off voltage (device turns off with "Battery" error) of about 1V/cell is well suited for NiMH Batteries. | The cut-off voltage (device turns off with "Battery" error) of about 1V/cell is well suited for NiMH Batteries. | ||
= Examples: Establish data connection between sigrok and MM 12 = | |||
'''Important:''' Driver is not (yet) part of mainline sigrok - see [https://github.com/Cymaphore/libsigrok this repository in github] if you want to use it already. | '''Important:''' Driver is not (yet) part of mainline sigrok - see [https://github.com/Cymaphore/libsigrok this repository in github] if you want to use it already. | ||
== Serial/USB == | |||
Assuming the meter is turned on, plugged in and the usb-serial driver is loadad and up (should happen automatically). /dev/ttyUSB0 is used as an example. | Assuming the meter is turned on, plugged in and the usb-serial driver is loadad and up (should happen automatically). /dev/ttyUSB0 is used as an example. | ||
| Line 91: | Line 91: | ||
$ smuview --driver benning-dmm:conn=/dev/ttyUSB0 | $ smuview --driver benning-dmm:conn=/dev/ttyUSB0 | ||
== Bluetooth LE == | |||
Assuming the meter is turned on and bluetooth activated on the meter and the PC. Important: Your Bluetooth-Controller must support BLE. | Assuming the meter is turned on and bluetooth activated on the meter and the PC. Important: Your Bluetooth-Controller must support BLE. | ||
| Line 118: | Line 118: | ||
$ smuview --driver benning-dmm:conn=bt/appa-b/18-7A-93-BF-47-62 | $ smuview --driver benning-dmm:conn=bt/appa-b/18-7A-93-BF-47-62 | ||
= Protocol = | |||
The protocol on Serial and BLE is the same like for most of the APPA based models. | The protocol on Serial and BLE is the same like for most of the APPA based models. | ||
= Resources = | |||
* [https://www.benning.de/products-en/testing-measuring-and-safety-equipment/digital-multimeter/benning-mm-12.html BENNING MM 12 Product Website] | * [https://www.benning.de/products-en/testing-measuring-and-safety-equipment/digital-multimeter/benning-mm-12.html BENNING MM 12 Product Website] | ||
Revision as of 12:37, 6 November 2020
 | |
| Status | in progress |
|---|---|
| Source code | serial-dmm |
| Counts | 40000 |
| IEC 61010-1 | CAT III (1000V) / CAT IV (600V) |
| Connectivity | Infrared (USB), Bluetooth LE |
| Measurements | voltage, current, frequency, duty cycle, resistance, continuity, conductance, diode, capacitance, temperature |
| Features | autorange, data hold, min/max/avg, crest, backlight, true-rms, dBm, dB, peak hold |
| Website | benning.de |
The BENNING MM 12 is a 40000 counts, CAT IV (600V) / CAT III (1000V) dual display handheld digital multimeter with USB and Bluetooth LE connectivity.
It is based on the APPA 506B, See also: APPA Multimeters.
A driver supporting these devices including the MM 12 has been created and will be included in mainline sigrok once it passes acception (more details in pull request #99).
Hardware
- ADC: CYRUSTEK ES51966
Photos and Teardown
MM 12 connected to SmuView visualizing readings from the power grid
Front view
Measuring voltage and frequency from the power grid
Display, automatic backlight on
Protective sleeve removed
Rear
Optical data port (USB/Serial)
Included data cable (APPA IC-300U)
Batteries and fuses
Teardown 1/14
Teardown 2/14
Teardown 3/14
Teardown 4/14
Teardown 5/14
Teardown 6/14
Teardown 7/14
Teardown 8/14
Teardown 9/14
Teardown 10/14
Teardown 11/14
Teardown 12/14
Teardown 13/14
Teardown 14/14
Review and Test
Usage of rechargable NiMH batteries
The device works quite well with rechargable batteries. Voltage boundaries are well selected to suit the needs of both Alkaline and NiMH cells. For NiMH the reported battery level is of course to low.
Battery indication
- FULL: >1.415 V/cell ... 5.66 V overall
- HALF: >1.290 V/cell ... 5.16 V overall
- LOW: >1.165 V/cell ... 4.66 V overall
- WARN: >1.015 V/cell ... 4.06 V overall
The cut-off voltage (device turns off with "Battery" error) of about 1V/cell is well suited for NiMH Batteries.
Examples: Establish data connection between sigrok and MM 12
Important: Driver is not (yet) part of mainline sigrok - see this repository in github if you want to use it already.
Serial/USB
Assuming the meter is turned on, plugged in and the usb-serial driver is loadad and up (should happen automatically). /dev/ttyUSB0 is used as an example.
List devices, if unsure what the serial port is:
# sigrok-cli --list-serial /dev/ttyUSB0 CP2102 USB to UART Bridge Controller - 2020y000231
Scan for MM 12 with USB/Serial connection:
$ sigrok-cli -d benning-dmm:conn=/dev/ttyUSB0 --scan
Show readings from connected meter:
$ sigrok-cli -d benning-dmm:conn=/dev/ttyUSB0 --continuous
Open in SmuView:
$ smuview --driver benning-dmm:conn=/dev/ttyUSB0
Bluetooth LE
Assuming the meter is turned on and bluetooth activated on the meter and the PC. Important: Your Bluetooth-Controller must support BLE.
Scan for BLE devices:
# sudo sigrok-cli --list-serial bt/appa-b/18-7A-93-BF-47-62 BENNING MM12 (BLE)
If your OS / UI supports it, you can also use the Bluetooth scanning capability from the system tray and pick the MAC address from the details there.
"18:7A:93:BF:47:62" acts as an example for the device address you will find. For sigrok the ":" must be replaced by "-" for now. That device address is used for the following examples, just replace it by the address of your own meter.
The full connection string then would look like this, as seen in the scanning result: bt/appa-b/18-7A-93-BF-47-62
Scan for MM 12 with BLE connection:
$ sigrok-cli -d benning-dmm:conn=bt/appa-b/18-7A-93-BF-47-62 --scan
Show readings from connected meter:
$ sigrok-cli -d benning-dmm:conn=bt/appa-b/18-7A-93-BF-47-62 --continuous
Open in SmuView:
$ smuview --driver benning-dmm:conn=bt/appa-b/18-7A-93-BF-47-62
Protocol
The protocol on Serial and BLE is the same like for most of the APPA based models.