Difference between revisions of "Talk:Tondaj SL-814"
Choogenboom (talk | contribs) (Modify Tondaj SL-814 to run off USB cable only and stay on permanently) |
Choogenboom (talk | contribs) |
||
| Line 1: | Line 1: | ||
We have interfaced this SPL meter to a TP-Link MR3020 running OpenWrt OS. The SL-814 had a few jumpers added to enable it to ( | We have interfaced this SPL meter to a TP-Link MR3020 running OpenWrt OS. The SL-814 had a few jumpers added to enable it to (1) always stay on and (2) be powered from the 5V on the USB connector. | ||
Circuit mods: | Circuit mods: | ||
1. Short C3 - causes it to turn on automatically and stay on whenever power is applied. | 1. Short C3 - causes it to turn on automatically and stay on whenever power is applied. | ||
2. jumper USB pin | 2. jumper USB pin 5 (pin 5 == top most pin closest to top of circuit board where top == LCD display side of PCB) across to 9V power trace (the fat one that runs past the USB connector) | ||
3. Jumper C12+ to u3 pins 2+3 shorting +9 to +5 (note there are TWO 5V regulators on the board, one for digital +5 and one for Analog +5, a good design practice isolating the two) | 3. Jumper C12+ to u3 pins 2+3 shorting +9 to +5 (note there are TWO 5V regulators on the board, one for digital +5 and one for Analog +5, a good design practice isolating the two) | ||
4. short R8 making "low battery" and associated not helpful auto power off go away | 4. short R8 making "low battery" and associated not helpful auto power off go away | ||
| Line 9: | Line 9: | ||
Cable mods | Cable mods | ||
1. My SL-814 from amazon did not come with a cable | 1. My SL-814 from amazon did not come with a cable | ||
2. the "USB" port on the SL-814 is a USB port in physical form only. What they are doing is using a USB connector to output serial TTL I/O from the Atmel's UART. it is in no way, shape | 2. the "USB" port on the SL-814 is a USB port in physical form only. What they are doing is using a USB connector to output serial TTL I/O from the Atmel's UART. it is in no way, shape or form USB and the claims on Amazon etc that it has USB are flat out false. | ||
3. Use a PL2303 to TTL cable and a USB type B connector donor cable. | 3. Use a PL2303 to TTL cable and a USB type B connector donor cable. | ||
4. connect | 4. Cut and strip the USB donor cable's B connector side and connect | ||
i. black - black | i. black - black (GND) | ||
ii. red - red | ii. red - red (+5) | ||
iii. green - white | iii. green - white (Data) | ||
iv. white - green | iv. white - green (Data) | ||
End Result | End Result | ||
Plug into your PC, assuming you have PL2303 driver should show up as a COM port or /dev/ttyUSBx in the case of OpenWrt/Linux. | Plug into your PC, assuming you have PL2303 driver should show up as a COM port or /dev/ttyUSBx in the case of OpenWrt/Linux. From there follow other advice on this wiki regarding commands and responses. | ||
Revision as of 14:08, 24 May 2013
We have interfaced this SPL meter to a TP-Link MR3020 running OpenWrt OS. The SL-814 had a few jumpers added to enable it to (1) always stay on and (2) be powered from the 5V on the USB connector.
Circuit mods: 1. Short C3 - causes it to turn on automatically and stay on whenever power is applied. 2. jumper USB pin 5 (pin 5 == top most pin closest to top of circuit board where top == LCD display side of PCB) across to 9V power trace (the fat one that runs past the USB connector) 3. Jumper C12+ to u3 pins 2+3 shorting +9 to +5 (note there are TWO 5V regulators on the board, one for digital +5 and one for Analog +5, a good design practice isolating the two) 4. short R8 making "low battery" and associated not helpful auto power off go away
Cable mods 1. My SL-814 from amazon did not come with a cable 2. the "USB" port on the SL-814 is a USB port in physical form only. What they are doing is using a USB connector to output serial TTL I/O from the Atmel's UART. it is in no way, shape or form USB and the claims on Amazon etc that it has USB are flat out false. 3. Use a PL2303 to TTL cable and a USB type B connector donor cable. 4. Cut and strip the USB donor cable's B connector side and connect
i. black - black (GND) ii. red - red (+5) iii. green - white (Data) iv. white - green (Data)
End Result Plug into your PC, assuming you have PL2303 driver should show up as a COM port or /dev/ttyUSBx in the case of OpenWrt/Linux. From there follow other advice on this wiki regarding commands and responses.