Difference between revisions of "Rohde&Schwarz HMO 1002 series"
(Add info about ethernet port and USB VCP/USBTMC port) |
(Add info how to connect) |
||
| Line 36: | Line 36: | ||
The device is equipped with an 100MBit/s ethernet port as well as a USB B device connector. USB can be switched | The device is equipped with an 100MBit/s ethernet port as well as a USB B device connector. USB can be switched | ||
from VCP (virtual COM port) to USBTMC mode via the Setup/Parameter menu. USB VID/PID is 0x0aad:0118 resp. 0x0aad:0119. | from VCP (virtual COM port) to USBTMC mode via the Setup/Parameter menu. USB VID/PID is 0x0aad:0118 resp. 0x0aad:0119. | ||
== Connecting == | |||
Devices connected via USB (both VCP and USBTMC mode) are autodetected by the hameg-hmo driver, and are usable with sigrok-cli and pulseview. | |||
Devices connected via Ethernet can not be autodetected, and are thus not usable with pulseview currently, [http://sigrok.org/bugzilla/show_bug.cgi?id=769 Bug#769]. | |||
<source lang="bash"> | |||
$ sigrok-cli --driver=hameg-hmo:conn=/dev/ttyACM0 -O analog -C CH1 --frames 1 | |||
$ sigrok-cli --driver=hameg-hmo:conn=usbtmc/0aad.0119 -O analog -C CH1 --frames 1 | |||
$ sigrok-cli --driver=hameg-hmo:conn=tcp-raw/192.168.1.20/5025 -O analog -C CH1 --frames 1 | |||
</source> | |||
== Resources == | == Resources == | ||
Revision as of 03:40, 18 April 2016
 | |
| Status | supported |
|---|---|
| Source code | hameg-hmo |
| Channels | 2 analog, 8 digital |
| Samplerate | 1GSa/s (interleaved), 500MSA/s (non interleaved) |
| Analog bandwidth | 50/70/100MHz (software license) |
| Vertical resolution | 8bits (HiRes up to 16bits) |
| Triggers | pulse width, slope, video, pattern, serial bus (optional) |
| Input impedance | 1MΩ‖16pF 200Vp CAT I |
| Memory | 1Mpts (mode/ch-dependent) |
| Display | 6.5" VGA (640x480), 256 colors |
| Connectivity | USB host/device, ethernet |
| Features | math: + / — / x / FFT, statistics, vertical sensitivity: 1mV/div - 10V/div, 4bit 50MHz pattern generator, 50kHz function generator |
| Website | rohde-schwarz.com |
The R&S 1002 Series is a 50-100MHz (software upgradable), 1GSa/s, 2 analog channel and 8 digital channel digital storage oscilloscope.
The base model can be upgraded from 50MHz to 70MHz or 100MHz with the HV572 resp HV512 option.
There are also options to decode several serial bus protocols:
- HV110/HOO10 (S)SPI/I2C/UART, analog and/or digital channels
- HV111/HOO11 (S)SPI/I2C/UART, analog channels only
- HV112/HOO12 CAN/LIN decoding/triggering, analog and/or digital channels
For usage of the digital channels the HO3508 logic probe is required.
Protocol
The device use same SCPI protocol as the HAMEG HMO compact series (HAMEG has been aquired by R&S).
The device is equipped with an 100MBit/s ethernet port as well as a USB B device connector. USB can be switched from VCP (virtual COM port) to USBTMC mode via the Setup/Parameter menu. USB VID/PID is 0x0aad:0118 resp. 0x0aad:0119.
Connecting
Devices connected via USB (both VCP and USBTMC mode) are autodetected by the hameg-hmo driver, and are usable with sigrok-cli and pulseview. Devices connected via Ethernet can not be autodetected, and are thus not usable with pulseview currently, Bug#769.
$ sigrok-cli --driver=hameg-hmo:conn=/dev/ttyACM0 -O analog -C CH1 --frames 1
$ sigrok-cli --driver=hameg-hmo:conn=usbtmc/0aad.0119 -O analog -C CH1 --frames 1
$ sigrok-cli --driver=hameg-hmo:conn=tcp-raw/192.168.1.20/5025 -O analog -C CH1 --frames 1