Difference between revisions of "Rigol DG1000z Series"

**Rigol DG1000z Series**
Status	in progress
Frequency (sine)	25-60MHz
Frequency (square)	25MHz
Frequency (other)	15-25MHz (pulse), 500-1000KHz (ramp)
Frequency (user)	10-20MHz
Waveforms	sine, square, ramp, pulse, harmonic, noise, arbitrary waveform
Waveform memory	2-8Mpts (16Mpts option)
Modulation	AM, FM, PM, DSB-AM, FSK, ASK, PWM
Connectivity	USBTMC, LAN
Website	rigolna.com

Revision as of 07:04, 6 September 2020

Rigol DG1000Z Series Arbitrary Waveform Generators are 2 channel, 25-60MHz signal generators with up to 16Mpts waveform memory.

Hardware on all these models is identical, only difference is in software/firmware.

Model	Channels	Max Frequency (Sine)	Max Frequency (Square)	Arbitrary Waveform Length	Frequency Counter
DG1022Z	2	25 MHz	25 MHz	2 Mpts *	Y
DG1032Z	2	30 MHz	25 MHz	8 Mpts *	Y
DG1062Z	2	60 MHz	25 MHz	8 Mpts *	Y

Digital:

TODO

Analog:

TODO

TODO

Depending on your type of connection you have to can either use the USBTMC connection parameter or the TCP/IP connection parameter. Examples:

 --driver=rigol-dg

or

 -d rigol-dg

(usually no parameters are needed when connecting via USB)

When connecting over TCP/IP need to specify ip address and port:

 --driver=scpi-dmm:conn=tcp-raw/192.168.42.42/5555

Check the capabilities of the meter's driver, and current state of settings:

 $ sigrok-cli -d rigol-dg --show

Check the capabilities specific to a channel (1 or 2):

 $ sigrok-cli -d rigol-dg --show -g 1

Enable or disable channel output (first channel):

 $ sigrok-cli -d rigol-dg -g 1 --set --config enabled=true
 $ sigrok-cli -d rigol-dg -g 1 --set --config enabled=false

Get or set the waveform function (second channel):

 $ sigrok-cli -d rigol-dg -g 2 --get pattern
 $ sigrok-cli -d rigol-dg -g 2 --set --config pattern=square

Acquire measurement data, in the current mode or in another specified mode:

 $ sigrok-cli -d rigol-dg --continuous
 $ sigrok-cli -d rigol-dg --time 10s
 $ sigrok-cli -d rigol-dg --samples 10

@@ Line 56: / Line 56: @@
 TODO
+== Example use ==
+Depending on your type of connection you have to can either use the [[Connection_parameters#USBTMC | USBTMC connection parameter]] or the [[Connection_parameters#TCP_RAW | TCP/IP connection parameter]]. Examples:
+  '''--driver=rigol-dg'''
+or
+  '''-d rigol-dg'''
+(usually no parameters are needed when connecting via USB)
+When connecting over TCP/IP need to specify ip address and port:
+  '''--driver=scpi-dmm:conn=tcp-raw/192.168.42.42/5555'''
+Check the capabilities of the meter's driver, and current state of settings:
+  $ '''sigrok-cli -d rigol-dg --show'''
+Check the capabilities specific to a channel (1 or 2):
+  $ '''sigrok-cli -d rigol-dg --show -g 1'''
+Enable or disable channel output (first channel):
+  $ '''sigrok-cli -d rigol-dg -g 1 --set --config enabled=true'''
+  $ '''sigrok-cli -d rigol-dg -g 1 --set --config enabled=false'''
+Get or set the waveform function (second channel):
+  $ '''sigrok-cli -d rigol-dg -g 2 --get pattern'''
+  $ '''sigrok-cli -d rigol-dg -g 2 --set --config pattern=square'''
+Acquire measurement data, in the current mode or in another specified mode:
+  $ '''sigrok-cli -d rigol-dg --continuous'''
+  $ '''sigrok-cli -d rigol-dg --time 10s'''
+  $ '''sigrok-cli -d rigol-dg --samples 10'''
 == Resources ==