Difference between revisions of "Protocol decoder:Esp8266"
| Line 1: | Line 1: | ||
{{Infobox protocol decoder | |||
| id = esp8266 | |||
| name = ESP8266 | |||
| description = WiFi Serial Transceiver. | |||
| status = planned | |||
| license = GPLv2+ | |||
| source_code_dir = | |||
| image = [[File:ESP8266_closeup.jpg|250px]] | |||
| input = uart | |||
| output = esp8266 | |||
| probes = — | |||
| optional_probes = — | |||
}} | |||
The '''esp8266''' protocol decoder supports the UART command protocol spoken by modules equipped with an [https://espressif.com/en/products/esp8266/ ESP8266] WiFi transceiver chip. | |||
== Hardware == | |||
The ESP8266 chip contains an [http://ip.cadence.com/ipportfolio/tensilica-ip/xtensa-customizable Xtensa] LX106 CPU and a radio for IEEE 802.11b/g/n. | |||
=== Modules === | === Modules === | ||
| Line 137: | Line 157: | ||
|} | |} | ||
</blockquote> | </blockquote> | ||
== Resources == | |||
* [http://www.esp8266.com ESP8266 Community Forum] | |||
** [http://www.esp8266.com/viewtopic.php?f=5&t=28 Module overview] | |||
* [https://nurdspace.nl/ESP8266 Translation of the chinese datasheet] | |||
* [https://github.com/esp8266/esp8266-wiki/wiki/Pin-definition ESP8266 pinout] | |||
* [http://zeptobars.ru/en/read/Espressif-ESP8266-wifi-serial-rs232-ESP8089-IoT Die shots of the chip] | |||
Revision as of 01:56, 6 November 2014
 | |
| Name | ESP8266 |
|---|---|
| Description | WiFi Serial Transceiver. |
| Status | planned |
| License | GPLv2+ |
| Source code | decoders/ |
| Input | uart |
| Output | esp8266 |
| Probes | — |
| Optional probes | — |
The esp8266 protocol decoder supports the UART command protocol spoken by modules equipped with an ESP8266 WiFi transceiver chip.
Hardware
The ESP8266 chip contains an Xtensa LX106 CPU and a radio for IEEE 802.11b/g/n.
Modules
Various online marketplaces sell modules containing the ESP8266 (and a few assisting components) that comes preprogrammed with a TCP/IP stack that can be controlled via RS232 commands.
- ESP-01
Connector: 2x4pin male 2.54mm header
Connector pinout Function Pin Pin Function 1 2 GND 3 4 5 6 VCC 7 8 (Note: The PCB has two square pads at the pin header, so it's not clear which one should be pin number 1. The table above assumes that the module is oriented as shown in the picture from the top, with the antenna on the right side, pin 1 is then in the top left corner and pin 8 next to the SPI flash chip.)
ESP-01, top
GigaDevice GD25Q40B 4Mbit SPI flash
- ESP-04
Connectors: 7 pin castellated holes on both sides (2mm distance)
Pinout of left connector Pin Function 1 VCC 2 3 4 5 6 7
Pinout of right connector Pin Function 1 2 3 4 5 6 n.c. 7 GND
- ESP-05
Connectors: 1x5pin pads (2.54mm distance), U.FL antenna connector
Connector pinout Pin Function 1 2 GND 3 4 5 VCC