Difference between revisions of "XZL Studio AX"
Jump to navigation
Jump to search
(Created page with "{{Infobox logic analyzer | image = | name = XZL Studio AX | status = supported | source_code_dir = fx2lafw | channels = 8 | samplera...") |
m |
||
(35 intermediate revisions by 4 users not shown) | |||
Line 1: | Line 1: | ||
{{DISPLAYTITLE:XZL_Studio AX}} | |||
{{Infobox logic analyzer | {{Infobox logic analyzer | ||
| image = | | image = [[File:Xzl studio ax mugshot.png|180px]] | ||
| name = | | name = XZL_Studio AX | ||
| status = supported | | status = supported | ||
| source_code_dir = fx2lafw | | source_code_dir = fx2lafw | ||
| channels = 8 | | channels = 8 + 1 | ||
| samplerate = 24MHz | | samplerate = 8ch @ 24MHz, 8+1ch @ 12MHz | ||
| samplerate_state = — | | samplerate_state = — | ||
| triggers = 1 | | triggers = 1 independent trigger + (SW-probe 0,1) | ||
| voltages = Digital | | voltages = Digital: max. 5.5V<br />Analog: -10V — +10V | ||
| | | threshold = Digital: Fixed: V<sub>IH</sub>=1.4V, V<sub>IL</sub>=0.8V | ||
| memory = none | | memory = none | ||
| compression = none | | compression = none | ||
| website = [http://www.hotmcu.com/xzl- | | price = $20 - 35 | ||
| website = [http://www.hotmcu.com/xzl-ax-oscilloscope-and-logic-analyzer-ax-pro-logic-analyzer-p-14.html?cPath=3_26 hotmcu.com] | |||
}} | }} | ||
The ''' | The '''XZL_Studio AX''' is a USB-based, 8-channel logic analyzer with up to 24MHz sampling rate, with 1 additional analog channel (theoretically 2, but only one of them can be used at a time; 3MHz analog bandwidth). | ||
It is a clone of the [[CWAV USBee | It is a clone of the [[CWAV USBee AX-Pro]]. | ||
In sigrok, we use the open-source [[fx2lafw]] firmware for this logic analyzer. | In sigrok, we use the open-source [[fx2lafw]] firmware for this logic analyzer. | ||
'''Note''': | '''Note''': [[fx2lafw]] currently doesn't support switching between the two possible analog channels, 1ACH (TODO: not verified on hardware) will be used unconditionally. | ||
See [[ | See [[XZL_Studio AX/Info]] for some more details (such as '''lsusb -v''' output) on the device. | ||
== Hardware == | == Hardware == | ||
* '''Main chip''': Cypress CY7C68013A-56LTXC (FX2LP) | * '''Main chip''': Cypress CY7C68013A-56LTXC (FX2LP), U6 | ||
* '''ADC''': 1x Texas Instruments TLC5510I (SO 24pin package) | * '''ADC''': 1x Texas Instruments TLC5510I (SO 24pin package), 8-Bit, 20 MSPS ADC, Single Channel, U10, outputs D1-D8 connected to PD0-PD7, OE# grounded, CLOCK from CTL2 on U6 | ||
* '''I2C EEPROM''': Atmel | * '''I2C EEPROM''': Atmel 24C02C | ||
* '''Low-dropout voltage regulator''': Advanced Monolithic Systems AMS1117-3.3 | * '''Low-dropout voltage regulator''': Advanced Monolithic Systems AMS1117-3.3 | ||
* '''Crystal''': 24MHz | * '''Crystal''': 24MHz | ||
* '''Multiplexer''': HCF4051 - Single 8-Channel Analog Multiplexer/Demultiplexer, U12, channel selectors B and C grounded, selector A controlled by PA0 on U6 | |||
* '''Op Amp''': LM358 - Single Supply Dual Operational Amplifiers, U15 | |||
* ... | * ... | ||
== Photos == | == Photos == | ||
<gallery> | |||
File:Studio XZL AX.jpeg|<small>Device, front</small> | |||
File:Studio XZL AX Probe Port.jpeg|<small>Probe port</small> | |||
File:Studio XZL AX USB.jpeg|<small>USB port</small> | |||
File:Studio XZL AX.back.jpg|<small>Device, back</small> | |||
File:Studio XZL AX PCB.jpeg|<small>PCB, top</small> | |||
File:Studio XZL AX PCB underside.jpeg|<small>PCB, bottom</small> | |||
File:Studio XZL AX clips.jpeg|<small>Probe clips</small> | |||
</gallery> | |||
== Protocol == | == Protocol == | ||
Line 45: | Line 56: | ||
== Resources == | == Resources == | ||
* [[EE Electronics ESLA201A]] - the same circuit (from firmware's point of view). PCB has been copied and altered, same silkscreen labels. No electrolytic caps, no resistive trimmers, larger screw-hole-keepouts, no cap on pin 13 at U10, no U13 (second MAX1044/ICL7660). Has extra button inside the box! | |||
[[Category:Device]] | [[Category:Device]] |
Latest revision as of 15:00, 30 June 2019
Status | supported |
---|---|
Source code | fx2lafw |
Channels | 8 + 1 |
Samplerate | 8ch @ 24MHz, 8+1ch @ 12MHz |
Samplerate (state) | — |
Triggers | 1 independent trigger + (SW-probe 0,1) |
Min/max voltage |
Digital: max. 5.5V Analog: -10V — +10V |
Threshold voltage | Digital: Fixed: VIH=1.4V, VIL=0.8V |
Memory | none |
Compression | none |
Price range | $20 - 35 |
Website | hotmcu.com |
The XZL_Studio AX is a USB-based, 8-channel logic analyzer with up to 24MHz sampling rate, with 1 additional analog channel (theoretically 2, but only one of them can be used at a time; 3MHz analog bandwidth).
It is a clone of the CWAV USBee AX-Pro.
In sigrok, we use the open-source fx2lafw firmware for this logic analyzer.
Note: fx2lafw currently doesn't support switching between the two possible analog channels, 1ACH (TODO: not verified on hardware) will be used unconditionally.
See XZL_Studio AX/Info for some more details (such as lsusb -v output) on the device.
Hardware
- Main chip: Cypress CY7C68013A-56LTXC (FX2LP), U6
- ADC: 1x Texas Instruments TLC5510I (SO 24pin package), 8-Bit, 20 MSPS ADC, Single Channel, U10, outputs D1-D8 connected to PD0-PD7, OE# grounded, CLOCK from CTL2 on U6
- I2C EEPROM: Atmel 24C02C
- Low-dropout voltage regulator: Advanced Monolithic Systems AMS1117-3.3
- Crystal: 24MHz
- Multiplexer: HCF4051 - Single 8-Channel Analog Multiplexer/Demultiplexer, U12, channel selectors B and C grounded, selector A controlled by PA0 on U6
- Op Amp: LM358 - Single Supply Dual Operational Amplifiers, U15
- ...
Photos
Protocol
Since we use the open-source fx2lafw firmware for this device, we don't need to know the protocol.
Resources
- EE Electronics ESLA201A - the same circuit (from firmware's point of view). PCB has been copied and altered, same silkscreen labels. No electrolytic caps, no resistive trimmers, larger screw-hole-keepouts, no cap on pin 13 at U10, no U13 (second MAX1044/ICL7660). Has extra button inside the box!