Difference between revisions of "ICStation USBRelay"
(→Protocol: Update) |
(Change status to supported) |
||
| (4 intermediate revisions by the same user not shown) | |||
| Line 2: | Line 2: | ||
| image = [[File:ICStation_ICSE012A-mugshot.png|180px]] | | image = [[File:ICStation_ICSE012A-mugshot.png|180px]] | ||
| name = ICStation USBRelay | | name = ICStation USBRelay | ||
| status = | | status = supported | ||
| source_code_dir = icstation-usbrelay | | source_code_dir = icstation-usbrelay | ||
| channels = 2, 4 or 8 | | channels = 2, 4 or 8 | ||
| Line 12: | Line 12: | ||
See [[ICStation_USBRelay/Info | Info]] for USB details. | See [[ICStation_USBRelay/Info | Info]] for USB details. | ||
'''WARNING:''' When reconnecting to the device (e.g. with sigrok-cli or SmuView) the connect will fail and the "query device"-command (0x50) will be interpreted as a bit mask and will turn on relays 1-4, 6 and 8. You have to power cycle the device to be able to reconnect! | |||
== Photos == | == Photos == | ||
| Line 30: | Line 32: | ||
The relay boards have a very simple and limited protocol. | The relay boards have a very simple and limited protocol. | ||
'''Note:''' Once the device has entered the command mode (0x51), every following byte will be interpreted as a mask for switching relays. | '''Note:''' Once the device is connected and has entered the command mode (0x51), every following byte will be interpreted as a bit mask for switching relays. There is no way to leave the command mode! | ||
{| border="0" width="95%" style="font-size: smaller;" class="alternategrey sigroktable" | {| border="0" width="95%" style="font-size: smaller;" class="alternategrey sigroktable" | ||
| Line 58: | Line 60: | ||
|- | |- | ||
| valign="top" style="white-space=nowrap;" | '''0x51''' | | valign="top" style="white-space=nowrap;" | '''0x51''' ''0xnn 0xnn ...'' | ||
| '''Start command mode.''' | | '''Start command mode.''' | ||
| Line 65: | Line 67: | ||
'''Note:''' You cannot leave the command mode! | '''Note:''' You cannot leave the command mode! | ||
Examples for ICSE014A | Examples for switching mask bytes (ICSE014A, 8 relays): | ||
{| border="0" width="100%" style="margin: 0;" class="alternategrey" | {| border="0" width="100%" style="margin: 0;" class="alternategrey" | ||
|- | |- | ||
| Line 114: | Line 116: | ||
[[Category:Device]] | [[Category:Device]] | ||
[[Category:Multiplexer]] | [[Category:Multiplexer]] | ||
[[Category: | [[Category:Supported]] | ||
Latest revision as of 18:10, 19 February 2023
 | |
| Status | supported |
|---|---|
| Source code | icstation-usbrelay |
| Channels | 2, 4 or 8 |
| Ratings | 10A @ 250VAC/30VDC, 12A @ 125VAC/28VDC |
| Connectivity | USB/Serial |
The ICStation USBRelay is a USB relay card with up to 8 relays. Models with 2 (ICSE013A), 4 (ICSE012A) and 8 (ICSE014A) relays exist.
See Info for USB details.
WARNING: When reconnecting to the device (e.g. with sigrok-cli or SmuView) the connect will fail and the "query device"-command (0x50) will be interpreted as a bit mask and will turn on relays 1-4, 6 and 8. You have to power cycle the device to be able to reconnect!
Photos
ICStation ICSE012A top
ICStation ICSE012A back
Hardware
- STM 8S003F3P6 microcontroller: datasheet
- Prolific PL-2303HX USB to UART Bridge: datasheet
- ULN2803AG relay driver: datasheet
Protocol
The relay boards have a very simple and limited protocol.
Note: Once the device is connected and has entered the command mode (0x51), every following byte will be interpreted as a bit mask for switching relays. There is no way to leave the command mode!
| Byte | Command | |||||||||
|---|---|---|---|---|---|---|---|---|---|---|
| 0x50 | Query the device model.
Response:
| |||||||||
| 0x51 0xnn 0xnn ... | Start command mode.
Every following byte will be interpreted as a bit mask for switching the relays. 0 will turn a relay on, 1 will turn a relay off. Note: You cannot leave the command mode! Examples for switching mask bytes (ICSE014A, 8 relays):
|
Example use
Detect the device and display its properties.
$ sigrok-cli -d icstation-usbrelay:conn=/dev/ttyUSB0 --show
Driver functions:
Multiplexer
Scan options:
conn
serialcomm
icstation-usbrelay - ICStation ICSE012A
Channel groups:
R1: channel
R2: channel
R3: channel
R4: channel
Supported configuration options across all channel groups:
enabled: on, off
Manipulate the state of relays.
$ sigrok-cli -d icstation-usbrelay:conn=/dev/ttyUSB0 --config channel_group=R1:enabled=off --config channel_group=R2:enabled=on --set