Difference between revisions of "Rigol MSO5000 Series"
(Initial version. Copied from various wiki pages.) |
|||
| (2 intermediate revisions by the same user not shown) | |||
| Line 60: | Line 60: | ||
'''sigrok-cli -d rigol-ds:conn=vxi/192.168.1.250 --config data_source=Live -o live.sr -O srzip --frames=1''' | '''sigrok-cli -d rigol-ds:conn=vxi/192.168.1.250 --config data_source=Live -o live.sr -O srzip --frames=1''' | ||
See [[Rigol-ds data source]] for more information on data source. | |||
== Digital channels == | == Digital channels == | ||
| Line 104: | Line 106: | ||
|} | |} | ||
Signal generator [https://github.com/sigrokproject/libsigrok/pull/96 PR#96] [https://sigrok.org/gitaction/libsigrok.git/8da5cfc..70cdf23 has been merged 2024-09-28] | |||
[[Category:Device]] | [[Category:Device]] | ||
[[Category:Oscilloscope]] | [[Category:Oscilloscope]] | ||
[[Category:Mixed-signal oscilloscope]] | [[Category:Mixed-signal oscilloscope]] | ||
[[Category:In | [[Category:In progress]] | ||
Latest revision as of 12:00, 29 September 2024
 | |
| Status | in progress |
|---|---|
| Source code | rigol-ds |
| Samplerate | up to 8GSa/s |
| Analog bandwidth | 70-350MHz (depending on model) |
| Vertical resolution | 8bits |
| Triggers | edge, pulse, runt, window, nth edge, slope, video, pattern, delay, timeout, duration, setup/hold, protocol (optional: RS232/UART, I²C, SPI, CAN, FlexRay, LIN, I2S, MIL-STD-1553) |
| Input impedance | 1MΩ‖17pF 300V RMS CAT I |
| Memory | 100Mpts (mode/ch-dependent), Option 200Mpts |
| Display | 9" 1024x800 |
| Connectivity | USB host/device, ethernet (LXI), HDMI, trigger out, pass/fail out |
| Features | math: +, —, x, /, FFT, A&&B, A |
| Website | rigolna.com |
The Rigol MSO5000 Series are 2-/4-channel oscilloscopes with an analog bandwidth of 70-350MHz and up to 8GS/s sampling rate.
Devices
| Model | Analog channels | Bandwidth | Digital channels |
|---|---|---|---|
| MSO5072 | 2 | 70MHz | 16 |
| MSO5074 | 4 | 70MHz | 16 |
| MSO5102 | 2 | 100MHz | 16 |
| MSO5104 | 4 | 100MHz | 16 |
| MSO5204 | 4 | 200MHz | 16 |
| MSO5354 | 4 | 350MHz | 16 |
Protocol
The device uses USBTMC or LXI via its Ethernet port for communication with a host PC. The protocol is based on SCPI commands.
Resources
Example use
Depending on your type of connection you have to can either use the USBTMC connection parameter or the VXI connection parameter. Examples:
When connecting over TCP/IP need to specify ip address and port:
-d rigol-ds:conn=vxi/192.168.42.42
sigrok-cli -d rigol-ds:conn=vxi/192.168.1.250 --config data_source=Live -o live.sr -O srzip --frames=1
See Rigol-ds data source for more information on data source.
Digital channels
The MSO500 Series has dedicated memory for digital channels, which is smaller in size than the analog memory. To have the same capturing time, the digital sampling rate is lower than the analog sampling rate.
Note: The support is not in mainline, yet. See | PR#95
Signal generator (option)
The optional signal gnerator can be used with the rigol-dg driver. For usage see Rigol DG800 Series
Suported waveforms
| Waveform | min frequency | max. frequency |
|---|---|---|
| Sine | 100mHz | 25MHz |
| Square | 100mHz | 15MHz |
| Ramp | 100mHz | 100kHz |
| Pulse | 100mHz | 1MHz |
| Arb | 100mHz | 10MHz |
| Noise | - | - |
| DC | - | - |
| Sinc | 100mHz | 1MHz |
| ExpRise | 100mHz | 1MHz |
| ExpFall | 100mHz | 1MHz |
| ECG | 100mHz | 1MHz |
| Gauss | 100mHz | 1MHz |
| Lorentz | 100mHz | 1MHz |
| Haversin | 100mHz | 1MHz |
Signal generator PR#96 has been merged 2024-09-28