Difference between revisions of "Sysclk LWLA1034"
(Now supported!) |
(Link to correct item on AliExpress) |
||
| (4 intermediate revisions by 2 users not shown) | |||
| Line 3: | Line 3: | ||
| name = Sysclk LWLA1034 | | name = Sysclk LWLA1034 | ||
| status = supported | | status = supported | ||
| source_code_dir = | | source_code_dir = sysclk-lwla | ||
| channels = 34 | | channels = 34 | ||
| samplerate = 125MHz (max) | | samplerate = 125MHz (max) | ||
| Line 12: | Line 12: | ||
| memory = 256Kbit/channel | | memory = 256Kbit/channel | ||
| compression = RLE | | compression = RLE | ||
| website = [http:// | | website = [http://www.aliexpress.com/item/free-shipping-New-arrival-Powerful-100MHz-34-channels-LA1034-Logic-Analyzer-Timing-State-Logic-Analyzer/1227957767.html aliexpress.com] | ||
}} | }} | ||
| Line 24: | Line 24: | ||
* Cypress CY7C68013A-56 (FX2) USB interface chip | * Cypress CY7C68013A-56 (FX2) USB interface chip | ||
* Cypress 256k×36 SRAM (likely a [http://www.cypress.com/?mpn=CY7C1361C-133AXC CY7C1361C-133AXC] or similar) | * Cypress 256k×36 SRAM (likely a [http://www.cypress.com/?mpn=CY7C1361C-133AXC CY7C1361C-133AXC] or similar) | ||
* STC15F104E 8051-based microcontroller | |||
The not-installed 10-pin connector between the USB socket and the large capacitor seems to connect to the JTAG pins of the FPGA. | The not-installed 10-pin connector between the USB socket and the large capacitor seems to connect to the JTAG pins of the FPGA. | ||
| Line 63: | Line 64: | ||
== Firmware == | == Firmware == | ||
We have received permission from the vendor to distribute the FPGA bitstreams with sigrok. Thus, the bitstreams are now included in the sigrok-firmware module. | |||
* The FX2 firmware is loaded from an EEPROM on the board, so that the final USB device descriptor is immediately available on power-up. | * The FX2 firmware is loaded from an EEPROM on the board, so that the final USB device descriptor is immediately available on power-up. | ||
Latest revision as of 23:27, 28 February 2014
 | |
| Status | supported |
|---|---|
| Source code | sysclk-lwla |
| Channels | 34 |
| Samplerate | 125MHz (max) |
| Samplerate (state) | ? |
| Triggers | 34 + extern |
| Min/max voltage | 0-5V |
| Threshold voltage | ? |
| Memory | 256Kbit/channel |
| Compression | RLE |
| Website | aliexpress.com |
The Sysclk LWLA1034 is a USB-based, 34-channel logic analyzer with up to 125MHz sampling rate.
See Sysclk LWLA1034/Info for more details (such as lsusb -v output) about the device.
Hardware
- Altera EP2C5Q208C8N (Cyclone II) FPGA
- Cypress CY7C68013A-56 (FX2) USB interface chip
- Cypress 256k×36 SRAM (likely a CY7C1361C-133AXC or similar)
- STC15F104E 8051-based microcontroller
The not-installed 10-pin connector between the USB socket and the large capacitor seems to connect to the JTAG pins of the FPGA.
Photos
(Note: The yellow/greenish markings weren't there, they're added by the photographer)
PCB for another device:
PCB, top
PCB, bottom
PCB, close-up
Cypress FX2
SRAM (marking removed)
Software
Firmware
We have received permission from the vendor to distribute the FPGA bitstreams with sigrok. Thus, the bitstreams are now included in the sigrok-firmware module.
- The FX2 firmware is loaded from an EEPROM on the board, so that the final USB device descriptor is immediately available on power-up.
- Endpoint 4 is used exclusively for loading a new bitstream into the FPGA.
- Endpoint 2 is used for sending commands to the FPGA firmware, with responses (if any) coming in from endpoint 6.
Reverse engineering of the vendor's custom protocol has been completed. See Sysclk LWLA1034/Protocol for the documentation.