Sysclk LWLA1034/Protocol

Command messages sent to the device appear to be a sequence of 16-bit words with little endian byte order. The first word in a message identifies the command type. Different command types have different message lengths. Some command types include a length field and allow for messages of variable length, others are of fixed size.

There are read commands which trigger an immediate response from the device, and write commands without a response.

Command 0001: Read Register

This command appears to read a 32-bit wide control register.

Command

Fixed length of 2 words (4 bytes).

ID	Address
0001	aaaa

Response

The response has a fixed length of 4 bytes. It is likely the content of a 32-bit register in either little endian or mixed endian byte order.

Command 0002: Write Register

This command appears to write a 32-bit value to a control register.

Command

Fixed length of 4 words (8 bytes).

ID	Address	Data
0002	aaaa	dddd-dddd

The data is likely either in little endian or in mixed endian byte order.

Command 0005: Write ???

This command appears to write 8 64-bit words at once. It is issued once after a transfer of captured data to the host has finished, but only for immediate (not triggered) captures.

Command

Fixed length of 33 words (66 bytes).

ID	Data 1	Data 2	Data 3	Data 4	Data 5	Data 6	Data 7	Data 8
0005	dddd-dddd-dddd-dddd	dddd-dddd-dddd-dddd	dddd-dddd-dddd-dddd	dddd-dddd-dddd-dddd	dddd-dddd-dddd-dddd	dddd-dddd-dddd-dddd	dddd-dddd-dddd-dddd	dddd-dddd-dddd-dddd

Command 0006: Read Memory at Address

This command appears to read a block from the device memory (probably the SRAM). It allows for random access using a 32-bit start address, and variable length via a 32-bit length field. The software uses this command to read captured data from the device's buffer.

Command

Fixed length of 5 words (10 bytes).

ID	Address	Length
0006	aaaa-aaaa	nnnn-nnnn

Both the address and the length are apparently encoded with mixed endian (2-1-4-3) byte order: MSW (16 bit) followed by LSW (16 bit), with the two bytes making up each individual 16-bit word in little endian order.

Response

The memory is apparently 36 bit wide: The size of the response in bits is 36 times the value in the length field. The software reads chunks of 120 words @ 36 bit at a time, which works out to an integer multiple of 8 (i.e. 4320 bits = 540 bytes). The final six reads are done in chunks of 8 words @ 36 bit, which works out to 36 bytes. Judging from this behavior, it seems that reading partial bytes is likely illegal.

Note that the software always starts reading at address 4 rather than 0. Presumably the firmware uses the first four 36-bit words for internal bookkeeping.

Command 0007: Configure Channels ???

The software issues this command once during start-up, and once for each capture operation as part of the setup sequence. It also issued when clicking the Stop button to cancel a capture in progress. The message format appears similar to command 0008 and its response.

Command

Tentatively: variable length of 3 words (6 bytes), plus length times 8 bytes.

ID	Length?	Data 1?	Data 2?	...
0007	nnnn-nnnn	dddd-dddd-dddd-dddd	dddd-dddd-dddd-dddd	...

The two argument words in the header look like a 32-bit length field in mixed endian (2-1-4-3) byte order. However, the software never uses any value other than 10 for this field, so it could just as well mean something completely different. The header seems to match the format of command 0008, and the payload looks similar to the response to command 0008.

Command 0008: Read Channel State ???

This command appears to read data from a streaming source, as there is no apparent address information. The software issues 34 of those in sequence every second when idle, likely in order to read out the state of each input channel.

Command

Fixed length of 3 words (6 bytes).

ID	Length?
0008	nnnn-nnnn

The two argument words look like a 32-bit length field in mixed endian (2-1-4-3) byte order. However, the software never uses any value other than 10 for this field, so it could just as well mean something completely different.

Response

Tentatively, if the message does indeed carry a length field: The response is a sequence of 64-bit words, i.e. 80 bytes for a length of 10.