Siemens B1105

Siemens B1105

Status	in progress
Counts	310000
IEC 61010-1	CAT III 1000 V, CAT IV 600 V
Connectivity	Infrared (RS232)
Measurements	voltage, current, resistance, capacitance, temperature, diode, continuity
Features	autorange, data hold
Website	[1]

The Siemens B1105 is a 310000 counts 1000V CAT III/600 V CAT IV handheld digital multimeter with IR (RS232) connectivity.

It is an OEM version of the Gossen Metrawatt  Metrahit 28S. The only differences seem to be the type, logo and color (light grey-blue print on knob, light grey-blue holster) and the voltage rating.

Hardware

• Power supply:
  • Battery: 2x 1,5 V IEC R 6, IEC LR 6 or corresponding NiCd rechargeable batteries
  • External power supply NA5/600 by Gossen Metrawatt, 5V, 600 mA
• Fuse:
  • Current 300 mA: FF (UR) 1,6 A/1000 V AC/DC (10 kA) 6,3 mm x 32 mm
  • Current 3A/10A: FF (UR) 10 A/1000 V AC/DC (30 kA) 10 mm x 38 mm

Photos

• 

  Package

• 

  Back

• 

  Inside

• 

  IR Interface

• 

  Display

Using the device with sigrok

The device is supported in Send Mode using a RS232 interface by the driver gmc-mh-sm-rs232 (in development) and will be detected as a Metrahit 28S. Set the multimeter to use the communication adaptor RS232.

The device might be not detected by the driver if it is in a mode where it sends data rarely, either with a huge send interval or with a measurement function that delivers a very low data rate, e.g. temperature measurements with K type sensor. Then it should be set to a mode with higher data rate during the initialisation of the driver.

Measurement functions and ranges

Measurement function	Range	Resolution	Accuracy	sigrok result	Remarks
V=	300 mV	1 μV	±(0,02% + 0,010% + 5)	mq V, unit V, mqflags DC
	3 V	10 μV	±(0,02% + 0,005% + 5)	"
	30 V	100 μV		"
	300 V	1 mV		"
	1000 V	10 mV		"
V≈	300 mV	10 µV	±(0,5% + 30) (> 500 Digit))	mq V, unit V, mqflags AC,RMS
	3 V	100 μV	±(0,2% + 30)	"
	30 V	100 μV		"
	300 V	1 mV		"
	1000 V	10 mV		"
V≃	300 mV	10 μV	±(0,5% + 30) (> 500 Digit))	mq V, unit V, mqflags AC,DC,RMS
	3 V	100 μV	±(0,2% + 30)	"
	30 V	100 μV		"
	300 V	1 mV		"
	1000 V	10 mV		"
V db≈	-48 - 63 dB	0,01 dB	± 0,1 dB	mq V, unit V, mqflags AC,RMS	Actually the 5 AC ranges, see there for accuracy.
V db≈ rel	-48 - 63 dB	0,01 dB	± 0,1 dB	mq V, unit V, mqflags AC,RMS	Actually the 5 AC ranges, see there for accuracy. To activate, press yellow button in dB mode, then do second measurement. Cannot be distinguished from non-rel measurement remotely.
A=	300.00 µA	1 nA	0,05% + 0,02% + 5	mq Curr., unit A, mqflags DC
	3.0000 mA	10 nA	0,05% + 0,01% + 5	"
	30.000 mA	100 nA	0,05% + 0,01% + 5	"
	300.00 mA	1 µA	0,1% + 0,01% + 5	"
	3.0000 A	100 µA	0,2% + 0,05% + 5	"
	10.000 A	1 mA	0,2% + 0,05% + 5	"
A≃	300.00 µA	10 nA	0,5% + 30	mq Curr., unit A, mqflags AC,DC,RMS
	3.0000 mA	100 nA		"
	30.000 mA	1 µA		"
	300.00 mA	10 µA		"
	3.0000 A	100 µA	0,7% + 30	"
	10.000 A	1 mA	0,5% + 30	"
Ω	300.00 Ω	1 mΩ	0,05% + 0.01% + 5	mq Res., unit Ω, mqflags -
	3.0000 kΩ	10 mΩ		"
	30.000 kΩ	100 mΩ		"
	300.00 kΩ	1 Ω		"
	3.0000 MΩ	10 Ω	0,1% + 0.02% + 5	"
	30.000 MΩ	100 Ω	1% + 0.2% + 5	"
Ohm/Cont.	300 Ω	100 mΩ	1% + 3%	mq Res., unit Ω, mqflags -
Diode/Cont.	300 mV	100 µV	0.2% + 3	mq V, unit V, mqflags DC,DIODE
Diode	3 V	100 µV	0.2% + 3	mq V, unit V, mqflags DC,DIODE
Cap. F	3.000 nF	1 pF	1.0% + 0.2	mq Cap., unit F, mqflags -
	30.00 nF	10 pF		"
	300.0 nF	100 pF		"
	3.000 µF	1 nF		"
	30.00 µF	10 nF		"
	300.0 µF	100 nF	±(5.0% + 6)	"
	3.000 mF	1 µF		"
	30.00 mF	1 µF		"
Hz≈, ≃	300.00 Hz	0.001 Hz	±(0.05% + 1)	mq Freq., unit Hz, mqflags AC,DC	To activate in AC, press yellow button twice.
	3.0000 kHz	0.01 Hz		"
	300.000 kHz	1 Hz		"
°C	Pt100/Pt1000 –200.0 - +100.0 °C	0.1 °C	±(0,5 K + 3)	mq Temp., unit °C, mqflags -
	Pt100/Pt1000 +100.0 - 850.0 °C		±(0,2% + 3)	mq Temp., unit °C, mqflags -
	K NiCr-Ni -270-+1372,0 °C		±(0,7% + 3)	"
	J Fe-CuNi -210 - +1200.0 °C		±(0,8% + 3)	"	Not tested yet due to lack of corresponding sensor.
°F	"	"	"	mq Temp., unit °F, mqflags -	Details and ranges like °C.
Event count				mq V, unit V, mqflags AC,RMS,REL	Counts events >= 2500 digits that last >=2s with a break >=2s. To activate, switch to voltage ACDC, press yellow button twice. Press up to 4 times to cycle parameters, press long to stop. See manual. Not useful remotely because the current measurement value is sent, not the counter.
Stop Watch		100 ns		(Time data)	Max. 100 Min. To activate, select a 3V-1000V≃ range manually, press yellow button, press AUTO for start/stop, DATA for reset. Using the stop watch delivers only voltage data and sometimes seems to bring the device into a mode where it even sends invalid data packets.
Data Hold				mqflags += HOLD	Disabled while IR interface is active on  Matthias' test device.
MIN				mqflags += MIN	Influences only display, via IR flag is set, but actual current value is delivered.
MAX				mqflags += MAX	Influences only display, via IR flag is set, but actual current value is delivered.

The column "sigrok result" contains in short form what the driver generates for the resp. data type.