Difference between revisions of "Kingst LA5016"
Jump to navigation
Jump to search
(introduce Kingst LA5016 device page) |
(reference "the series" from the LA5016 device page) |
||
| (One intermediate revision by the same user not shown) | |||
| Line 7: | Line 7: | ||
| samplerate = 500MHz max. | | samplerate = 500MHz max. | ||
| samplerate_state = — | | samplerate_state = — | ||
| triggers = Level | | triggers = Level, Edge | ||
| voltages = -50V — 50V tolerant | | voltages = -50V — +50V tolerant | ||
| threshold = -4.0V—+4.0V, min step 0.01V | | threshold = -4.0V — +4.0V, min step 0.01V | ||
| memory = 2Gib RAM (256MiB) | | memory = 2Gib RAM (256MiB) | ||
| compression = Yes | | compression = Yes | ||
| Line 16: | Line 16: | ||
The '''Kingst LA5016''' is a USB-based, 16-channel logic analyser with 500MHz maximum sampling rate and 256MiB sample memory. | The '''Kingst LA5016''' is a USB-based, 16-channel logic analyser with 500MHz maximum sampling rate and 256MiB sample memory. | ||
It is part of | It is part of the [[Kingst LA Series]] and is supported by the '''kingst-la2016''' sigrok driver. | ||
The USB identification is | The USB identification is shared among Kingst LA devices. See [[Kingst LA2016]], the same VID:PID and the same USB endpoints are used. | ||
== Hardware == | == Hardware == | ||
| Line 35: | Line 35: | ||
<gallery> | <gallery> | ||
File:Kingst- | File:Kingst-la5016-size-compared.png|<small>Size comparison LA5016 and LA2016</small> | ||
File:Kingst- | File:Kingst-la5016-connectors.png|<small>Probe connectors LA5016 and LA2016</small> | ||
File:Kingst- | File:Kingst-la5016-case-open.png|<small>Case components (two U shaped symmetric halves, and faces)</small> | ||
File:Kingst- | File:Kingst-la5016-pcb-top.png|<small>LA5016 PCB, top side</small> | ||
File:Kingst- | File:Kingst-la5016-pcb-bottom.png|<small>LA5016 PCB, bottom side</small> | ||
</gallery> | </gallery> | ||
== Protocol == | == Protocol == | ||
See the [[Kingst | See the [[Kingst LA Series]] page, all devices communicate to the host in identical ways. | ||
== Firmware == | == Firmware == | ||
Device firmware must be extracted from vendor software before sigrok use. See [[Kingst | Device firmware must be extracted from vendor software before sigrok use. See [[Kingst LA Series]] for details. | ||
[[Category:Device]] | [[Category:Device]] | ||
[[Category:Logic analyzer]] | [[Category:Logic analyzer]] | ||
[[Category:Supported]] | [[Category:Supported]] | ||
Latest revision as of 14:25, 27 February 2022
 | |
| Status | supported |
|---|---|
| Source code | kingst-la2016 |
| Channels | 16 |
| Samplerate | 500MHz max. |
| Samplerate (state) | — |
| Triggers | Level, Edge |
| Min/max voltage | -50V — +50V tolerant |
| Threshold voltage | -4.0V — +4.0V, min step 0.01V |
| Memory | 2Gib RAM (256MiB) |
| Compression | Yes |
| Website | qdkingst.com |
The Kingst LA5016 is a USB-based, 16-channel logic analyser with 500MHz maximum sampling rate and 256MiB sample memory. It is part of the Kingst LA Series and is supported by the kingst-la2016 sigrok driver.
The USB identification is shared among Kingst LA devices. See Kingst LA2016, the same VID:PID and the same USB endpoints are used.
Hardware
TODO Add more details.
- Cypress FX2 MCU
- AT24C02 EEPROM
- Cyclone IV FPGA (Altera/Intel)
- U10 authentication device
- 2Gib DRAM
- a bunch of regulators
- opamp for input threshold control
Photos
Size comparison LA5016 and LA2016
Probe connectors LA5016 and LA2016
Case components (two U shaped symmetric halves, and faces)
LA5016 PCB, top side
LA5016 PCB, bottom side
Protocol
See the Kingst LA Series page, all devices communicate to the host in identical ways.
Firmware
Device firmware must be extracted from vendor software before sigrok use. See Kingst LA Series for details.