Difference between revisions of "PoLabs PoScope Mega50"

Revision as of 16:58, 5 January 2020

See PoScopeMega50/Info for lsusb information.

Cypress CY7C68013A-56: USB Microcontroller
Analog Devices AD9288: 8-Bit Dual A/D Converter
NXP LPC1111F: Cortex-M0 based microcontroller (For the output probably)
NXP PCA9555: 16 I/O CMOS device
4x Nexpia: 74HC4052: Dual 4-channel analog multiplexer/demultiplexer (two per analog channel)

Coming soon

The main communication when setting it up/changing configuration always goes like this:

The host sends a "URB_BULK out" command where there are 64 bytes of data.

The device sends a packet with 4 times 0x00 as data

The host returns the same data but with an 0x00 instead of an 0x01 at byte 16

The device returns a "URB_BULK in" command with a lot of data in the 64 bytes of data.

The setup:

// In the following examples, I'm only talking about the 64 bytes of data, because (I think) everything else gets handled by the driver itself

//I'm making assumptions about what the commands do

Booting:

the host sends 0xa2 followed by 63 0x00

the host sends 0xa8 followed by 63 0x00

the host sends 0xa4 + 0x30 + 0x00 + 0x20 + 60 * 0x00

now, the host counts bytes 1 and 2 up in 0x20 steps, always 0xa4 at byte 0 like that:

this is probably to clean out old values

byte 0	1	2	3	4-64
0xa4 +	0x30 +	0x20 +	0x20 +	60 * 0x00
0xa4 +	0x30 +	0x40 +	0x20 +	60 * 0x00
0xa4 +	0x30 +	0x60 +	0x20 +	60 * 0x00
0xa4 +	0x30 +	0x80 +	0x20 +	60 * 0x00
0xa4 +	0x30 +	0xa0 +	0x20 +	60 * 0x00
0xa4 +	0x30 +	0xc0 +	0x20 +	60 * 0x00
0xa4 +	0x30 +	0xe0 +	0x20 +	60 * 0x00
0xa4 +	0x31 +	0x00 +	0x20 +	60 * 0x00
0xa4 +	0x31 +	0x20 +	0x20 +	60 * 0x00

until byte 1 is 0x3f and byte 2 is 0xe0

then the host sends: 0xa4 + 0x40 + 0x00 + 0x00 + 60 * 0x00

Starting (setting modes and other stuff probably):

0xa5 +	0x28 +	0x01 +	0x01 +	0x00 +	0x00 +	58 * 0x00
0xa6 +	0x28 +	0x07 +	0x00 +	0x00 +	0x00 +	58 * 0x00
0xa5 +	0x28 +	0x01 +	0x06 +	0x00 +	0x00 +	58 * 0x00
0xa5 +	0x28 +	0x01 +	0x01 +	0x00 +	0x00 +	58 * 0x00
0xa6 +	0x28 +	0x07 +	0x00 +	0x00 +	0x00 +	58 * 0x00
0x06 +	0x00 +	0x00 +	0x00 +	0x00 +	0x00 +	58 * 0x00	maybe initializes mode change. always comes before b2
0xb2 +	0x00 +	0x00 +	0x01 +	0xe0 +	0x14 +	58 * 0x00	b2 could set the mode. it repeats with other data when switching modes
0x05 +	0xc7 +	0x00 +	0x00 +	0x00 +	0x00 +	58 * 0x00

after that you can ask for data with:

  0ad5ffff000000000900000100ff00860300000000

@@ Line 139: / Line 139: @@
 <th>0x01 + </th>
 <th>0x00 + </th>
-<th>59 * 0x00</th>
+<th>0x00 + </th>
+<th>58 * 0x00</th>
 </tr>
 <tr>
@@ Line 147: / Line 148: @@
 <th>0x00 + </th>
 <th>0x00 + </th>
-<th>59 * 0x00</th>
+<th>0x00 + </th>
+<th>58 * 0x00</th>
 </tr>
 <tr>
@@ Line 155: / Line 157: @@
 <th>0x06 + </th>
 <th>0x00 + </th>
-<th>59 * 0x00</th>
+<th>0x00 + </th>
+<th>58 * 0x00</th>
 </tr>
 <tr>
@@ Line 163: / Line 166: @@
 <th>0x01 + </th>
 <th>0x00 + </th>
-<th>59 * 0x00</th>
+<th>0x00 + </th>
+<th>58 * 0x00</th>
 </tr>
 <tr>
@@ Line 171: / Line 175: @@
 <th>0x00 + </th>
 <th>0x00 + </th>
-<th>59 * 0x00</th>
+<th>0x00 + </th>
+<th>58 * 0x00</th>
 </tr>
 <tr>
@@ Line 179: / Line 184: @@
 <th>0x00 + </th>
 <th>0x00 + </th>
-<th>59 * 0x00</th>
+<th>0x00 + </th>
+<th>58 * 0x00</th>
+<th>maybe initializes mode change. always comes before b2</th>
 </tr>
 <tr>
@@ Line 189: / Line 196: @@
 <th>0x14 + </th>
 <th>58 * 0x00</th>
+<th>b2 could set the mode. it repeats with other data when switching modes</th>
 </tr>
 <tr>
@@ Line 196: / Line 204: @@
 <th>0x00 + </th>
 <th>0x00 + </th>
-<th>59 * 0x00</th>
+<th>0x00 + </th>
+<th>58 * 0x00</th>
 </tr>
 </table>
+after that you can ask for data with:
+ad5ffff000000000900000100ff00860300000000