Difference between revisions of "Hantek PSO2020"
Jump to navigation
Jump to search
Martinloren (talk | contribs) |
Martinloren (talk | contribs) |
||
| Line 68: | Line 68: | ||
|} | |} | ||
'''Cypress FX2 pinout | '''Cypress FX2 pinout''': | ||
{| border="0" style="font-size: smaller" class="alternategrey sortable sigroktable" | {| border="0" style="font-size: smaller" class="alternategrey sortable sigroktable" | ||
|- | |- | ||
| Line 75: | Line 75: | ||
|- | |- | ||
| | | CTL0 | ||
| Connected to AD9288 ENC<sub>A</sub> | | Connected to AD9288 ENC<sub>A</sub>, to ENC<sub>B</sub> with an inverter. and to FX2 IFCLK. | ||
|- | |- | ||
| PB0-PB7 | | PB0-PB7 | ||
| Line 83: | Line 83: | ||
| PD0-PD7 | | PD0-PD7 | ||
| Connected to AD9288 D0<sub>B</sub>-D7<sub>B</sub>. | | Connected to AD9288 D0<sub>B</sub>-D7<sub>B</sub>. | ||
|- | |||
| PA0, PA1, PA5 (Inputs) | |||
| Connected to the 3 buttons | |||
|- | |- | ||
| PA7 | | PA7 | ||
| | | AC/DC Relay | ||
|- | |- | ||
| | | PA6 | ||
| Green LED | | Green LED | ||
|- | |||
| PE1 | |||
| Red LED + front light | |||
|} | |} | ||
Revision as of 05:58, 8 August 2018
 | |
| Status | |
|---|---|
| Source code | [1] |
| Channels | 1 |
| Samplerate | 96MHz |
| Analog bandwidth | 20MHz |
| Vertical resolution | 8bit |
| Triggers | none (SW-only) |
| Input impedance | 1MΩ‖25pF |
| Memory | none |
| Display | none |
| Connectivity | USB |
| Website | hantek.com |
The Hantek PSO2020 is a USB-based, 1-channel oscilloscope with an analog bandwidth of 20MS/s and 96MS/s sampling rate. Wide input rage, from ±100mV to ±50V.
See Hantek PSO2020/Info for more details (such as lsusb -v output) about the device.
Hardware
- USB: Cypress CY7C68013A-100AXC (FX2LP) (datasheet)
- 256-byte I²C EEPROM: Microchip 24LC02BI (datasheet)
- 1x 8-channel analog multiplexer/demultiplexer (U6): NXP 74HC4051D (datasheet)
- 1A low-dropout voltage regulator (3.3V): Advanced Monolithic Systems AMS1117-3.3 (datasheet)
- ?? 2W, fixed input, isolated & unregulated dual/single output DC/DC converter: Mornsun A_S-2WR2 (A0505S-2WR2) (datasheet)
- 8-bit, 40/80/100MHz, dual ADC: Analog Devices AD9288 (datasheet)
- ?? 4x 145 MHz FastFET Op Amp: Analog Devices AD8065 (datasheet)
- Crystal: 24MHz
- 1x Photocoupler (U100): Toshiba TPL280 (datasheet)
- 1x 4.5V Relay (used for AC/DC Coupling - U10): NEC UD2-4.5NU (datasheet)
- 1x ±5V DC/DC Coverter (U13): INOUT A0505S (datasheet)
Microchip 24LC02BI pinout:
| (Low, but not GND) A0 | 1- | O | -8 | VCC |
| (GND) A1 | 2- | -7 | WP (GND) | |
| (GND) A2 | 3- | -6 | SCL (FX2 SCL) | |
| VSS | 4- | -5 | SDA (FX2 SDA) |
Analog Devices ADS9288 pinout:
| AD9288 pins | Description |
|---|---|
| S1, S2 | Tied to VCC. "Data Align Enabled (data from both channels available on rising edge of Clock A. Channel B data is delayed a 1/2 clock cycle).". |
| DFS | Tied to GND. Data format select = "offset binary" (not "twos complement"). |
| REF_IN_A, REF_IN_B | Tied to REF_OUT. |
| AINA, AINB | Analog input channels. |
Cypress FX2 pinout:
| FX2 pins | Description |
|---|---|
| CTL0 | Connected to AD9288 ENCA, to ENCB with an inverter. and to FX2 IFCLK. |
| PB0-PB7 | Connected to AD9288 D0A-D7A. |
| PD0-PD7 | Connected to AD9288 D0B-D7B. |
| PA0, PA1, PA5 (Inputs) | Connected to the 3 buttons |
| PA7 | AC/DC Relay |
| PA6 | Green LED |
| PE1 | Red LED + front light |
Photos
Box Front
Box Back
Device
Inside Front
Inside Back
Inside Detail
Protocol
Firmware
Note: The firmware is not flashed into the device permanently! It will be automatically "uploaded" to the Cypress FX2's SRAM every time you attach the device to a USB port.
EEPROM layout
The device has a 256-byte I²C EEPROM with the following layout:
c0 b4 04 23 60 00 00 00 91 91 91 91 8a 8a 85 85 81 81 91 91 8a 8a 85 81 81 81 81 81 91 91 91 91 8a 8a 85 85 81 81 91 91 8a 8a 85 81 81 81 81 81 ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
Description:
| Bytes | Description |
|---|---|
| 0 | 0xc0: FX2 "c0 load" mode, i.e. VID/PID/DID are loaded from EEPROM (but not firmware). |
| 1-2 | 0x04b4: USB vendor ID (VID). |
| 3-4 | 0x6023: USB product ID (PID). |
| 5-6 | 0x0000: USB device ID (DID). |
| 7 | 0x00: FX2 configuration byte (see FX2 TRM for details). |
| 8-47 | Unknown. Possibly calibration data? |
| 48-255 | All-0xff. |