Difference between revisions of "Hantek 6022BE"
(→Hardware: set hardware types) |
(→Protocol: Add protocol info) |
||
| Line 20: | Line 20: | ||
== Protocol == | == Protocol == | ||
The protocol was reverse engineered and documented in: https://github.com/rpcope1/Hantek6022API/blob/master/REVERSE_ENGINEERING.md | |||
Copied from that page the main data: | |||
{| class="wikitable" | |||
!|Oscilloscope Command | |||
!| bRequest Value | |||
!|Other Notes | |||
|- | |||
|Set CH0 voltage range ||0xE0 ||Possible values: 1,2,5,10 (5V, 2.5V, 1V, 500mV). | |||
|- | |||
|Set CH1 voltage range ||0xE1 ||Possible values: 1,2,5,10 (5V, 2.5V, 1V, 500mV). | |||
|- | |||
|Set Sampling Rate ||0xE2 ||Possible values: 48, 30, 24, 16, 8, 4, 1 (MHz) and 50,20,10 (*10kHz). | |||
|- | |||
|Trigger Oscilloscope ||0xE3 ||Clear the FIFO on the FX2LP | |||
|- | |||
|Read/Write EEPROM ||0xA2 ||Read or write the eeprom built into the scope. | |||
|- | |||
|Read/Write Firmware ||0xA0 ||Read or write the scope firmware. Must be done on scope initialization | |||
|- | |||
|} | |||
All commands are sent with index = 0x00, the calibration commands are sent with value 0x08, the 0xEx requests are sent with value 0x00, and the value for R/W command is dependent on the Cypress protocol for interacting with the firmware. | |||
Additionally, a bulk read from end point 0x86 reads the current contents of the FIFO, which the ADC is filling. The reference Python libusb code should give further insight into the means for which to interact with the device. | |||
== Extracting the firmware == | == Extracting the firmware == | ||
Revision as of 19:41, 27 May 2015
The Hantek 6022BE is a USB-based, 2-channel oscilloscope with an analog bandwidth of 20MS/s sampling rate.
Hardware
- Main chip + USB: FX2LP
- Main oscillator: unknown
Photos
Hantek 6022BE
Hantek 6022BE PCB
Hantek 6022BE PCB Back
Hantek 6022BE feedback resistor selector
Hantek 6022BE FX2LP mcu
Protocol
The protocol was reverse engineered and documented in: https://github.com/rpcope1/Hantek6022API/blob/master/REVERSE_ENGINEERING.md
Copied from that page the main data:
| Oscilloscope Command | bRequest Value | Other Notes |
|---|---|---|
| Set CH0 voltage range | 0xE0 | Possible values: 1,2,5,10 (5V, 2.5V, 1V, 500mV). |
| Set CH1 voltage range | 0xE1 | Possible values: 1,2,5,10 (5V, 2.5V, 1V, 500mV). |
| Set Sampling Rate | 0xE2 | Possible values: 48, 30, 24, 16, 8, 4, 1 (MHz) and 50,20,10 (*10kHz). |
| Trigger Oscilloscope | 0xE3 | Clear the FIFO on the FX2LP |
| Read/Write EEPROM | 0xA2 | Read or write the eeprom built into the scope. |
| Read/Write Firmware | 0xA0 | Read or write the scope firmware. Must be done on scope initialization |
All commands are sent with index = 0x00, the calibration commands are sent with value 0x08, the 0xEx requests are sent with value 0x00, and the value for R/W command is dependent on the Cypress protocol for interacting with the firmware.
Additionally, a bulk read from end point 0x86 reads the current contents of the FIFO, which the ADC is filling. The reference Python libusb code should give further insight into the means for which to interact with the device.