+0.5.3 (2019-12-11)
+------------------
+
+Note: This release does NOT change the libsigrokdecode public C API in
+incompatible ways. This means existing frontends should not require any
+changes. However, individual PDs and their output changed, which may
+require some adaptations on the user's side in some cases.
+
+ * New supported protocol decoders:
+ - lin Local Interconnect Network (LIN) protocol
+ - x2444m Xicor X2444M/P nonvolatile static RAM protocol
+ - ds2408 1-Wire 8-channel addressable switch
+ - cc1101 Low-power sub-1GHz RF transceiver chip
+ - enc28j60 Microchip ENC28J60 10Base-T Ethernet controller protocol
+ - pca9571 NXP PCA9571 8-bit I²C output expander
+ - seven_segment 7-segment display protocol
+ - amulet_ascii Amulet Technologies LCD controller ASCII protocol
+ - tdm_audio TDM multi-channel audio protocol
+ - signature Annotate signature of logic patterns
+ - nes_gamepad NES gamepad button states
+ - flexray Automotive network communications protocol
+ - ir_rc6 RC-6 infrared remote control protocol
+ - ieee488 IEEE-488 General Purpose Interface Bus (GPIB/HPIB or IEC)
+ - hdcp HDCP protocol over HDMI
+ * All decoders must implement a reset() method now. It should reset all
+ PD-internal state and will be called when the decoder is restarted from
+ scratch (by frontends) with new data.
+ * Fix various memory leaks and bad memory accesses (e.g. bug #1374).
+ * Build system: Add support for Python 3.8 (bug #1438).
+ * Various compiler warning fixes.
+ * Slightly more detailed and easier to read log messages in some places.
+ * Fix incorrect decoder 'output' metadata.
+ * Improve annotation row ordering in various PDs.
+ * ook:
+ - Fix two typos causing decode issues.
+ * uart:
+ - Add support for break condition detection.
+ - Add 'FRAME' Python output type that communicates frame validity.
+ - Add '[rx|tx]_packet_delimiter' options.
+ - Add '[rx|tx]_packet_len' options.
+ - Communicate periods of idle frames to stacked decoders.
+ - Add 'ignore' parity type, remove unsupported 'check_parity' option.
+ - Shorten/rename various decoder option names.
+ * spiflash:
+ - Add support for Winbond W25Q80DV and Atmel AT25xxx.
+ - Add support for the chip erase commands (CE, CE2).
+ - Add support for write enable state tracking.
+ - Remember write protection latch from status registers.
+ - Fix WRSR incorrectly using MISO for register decodes.
+ - Add "EEPROM" to descriptions to increase discoverability in UIs.
+ * i2s:
+ - Fix incorrect channel assignment.
+ - Fix usage of the incorrect edge for the data sampling.
+ * ds1307:
+ - Fix incorrect unit for frequencies above 1Hz.
+ - Fix incorrect AM/PM flag handling.
+ * ir_rc5:
+ - Fix an incorrect command value.
+ - Massively improve performance via proper self.wait() usage.
+ * onewire_network:
+ - Add support for the 'Resume ROM' command.
+ - Add a 'Disable Test Mode' command for DS2408.
+ * sdcard_spi:
+ - Add support for CMD24 including payload data (bug #1365).
+ - Fix duplicated 'End bit' annotation emission.
+ - Fix incorrect handling of CMD17 (bug #1377).
+ - Add "Card is busy" annotations for CMD24 (bug #1376).
+ * spi:
+ - Add support for "transfer" annotations.
+ * atsha204a:
+ - Add support for ATECC508A.
+ - Display OtherData parameter correctly when Verify command is executed
+ in Validate mode.
+ - Only call output_tx_bytes() when the bytes buffer is not empty.
+ * usb_request:
+ - Append OUT data only if it has been ACK'd.
+ - Always keep IN and OUT transfers separate. In case the transfer is an
+ IN transfer, set the high bit as used in the endpoint descriptors (i.e.
+ 0x81 is IN enpoint 1, 0x01 is OUT endpoint 1).
+ - Use separate annotation rows for IN, OUT and CONTROL (bug #1046).
+ - Allow configuration of BULK IN transfer display via an option.
+ * modbus:
+ - Make C->S and S->C configurable via options.
+ - Add a 'framegap' option.
+ * mrf24j40:
+ - Add RX/TX frame annotations.
+ - Add TX retries/fails and CCAFAIL support.
+ * eeprom93xx:
+ - Add ASCII format support.
+ - Add OUTPUT_BINARY support.
+ * can:
+ - Add CAN-FD support.
+ - Add new 'fast_bitrate' option.
+ - More robust sample point position for low sample rates.
+ * gpib, iec:
+ - Removed in favor of the new ieee488 decoder.
+ * ir_nec:
+ - Fix decoder when running it multiple times (bug #1243).
+
+0.5.2 (2018-09-12)
+------------------
+
+Note: This release does NOT change the libsigrokdecode public C API in
+incompatible ways. This means existing frontends should not require any
+changes. However, individual PDs and their output changed, which may
+require some adaptations on the user's side in some cases.
+
+ * New supported protocol decoders:
+ - mcs48 Intel MCS-48 external memory access protocol
+ - st7735 Sitronix ST7735 TFT controller protocol
+ - atsha204a Microchip ATSHA204A CryptoAuthentication device
+ - cfp 100 Gigabit C form-factor pluggable (CFP) protocol
+ - jtag_ejtag MIPS EJTAG protocol
+ - swim STM8 Single Wire Interface Module (SWIM) protocol
+ - cec HDMI Consumer Electronics Control (CEC) protocol
+ - miller Miller encoding protocol
+ - ook On-off keying protocol
+ - ook_oregon Oregon Scientific weather sensor protocol
+ - ook_vis OOK visualisation in various formats
+ * Various minor performance improvements in the backend.
+ * Fix an issue causing decoder termination to take a long time.
+ * Fix multiple self.put() memory leaks (bug #329).
+ * Fix multiple memory leaks reported by scan-build.
+ * Show a backtrace when the decode aborts due to an error (bug #1158).
+ * Perform the log level check for non-default handlers as well (bug #698).
+ * Fix multiple compiler warnings.
+ * Compiler: Add -Wshadow -Wformat=2 -Wno-format-nonliteral -Wfloat-equal.
+ * Build system: Add Python 3.7 support.
+ * Fix a 'make install' issue that happens with Python >= 3.7.
+ * Add two missing Python GIL release operations.
+ * libsigrokdecode API changes:
+ - Add the srd_log_callback_get() API call.
+ - Add the SRD_ERR_TERM_REQ error code.
+ * dcf77:
+ - Annotate invalid dow and month fields, do not abort execution (bug #1173).
+ - Annotate unexpected bit numbers and values, do not abort execution.
+ * spiflash:
+ - Add basic Adesto AT45DBxx support (WRITE1/2, STATUS).
+ - Add Adesto AT45DB161E metadata.
+ * jtag:
+ - Fix shifting of registers (bug #1066).
+ * jtag_stm32:
+ - Fix handling of boundary scan TAP and incorrect state transitions.
+ * eeprom24xx:
+ - Add ON Semi CAT24C256 and CAT24M01 support.
+ * counter:
+ - Emit wider annotations to improve readability in UIs (bug #1210).
+ - Add support for user specified initial counter values (bug #1229).
+ - Add an option to ignore a certain number of edges.
+ - Let the user decide how to handle the initial dead_cycles state.
+ * mdio:
+ - Accept MDIO READ without previous ADDRESS command (bug #1258).
+ * edid:
+ - Add support for extension blocks.
+ - Various annotation improvements.
+ * spi:
+ - Fix an issue causing an AttributeError during certain decodes.
+ * usb_power_delivery:
+ - Emit more details in annotations (power, PDO type, RDO info).
+ - Add PPS support.
+ - Add better USB Power Delivery 3.0 support.
+
0.5.1 (2018-04-12)
------------------
* jitter:
- Avoid Unicode string literals (bug #569).
* jtag:
- - Fix/enable OUT_PYTHON output.
+ - Fix/enable OUTPUT_PYTHON output.
- Add more annotations, fix a SHIFT-IR/-DR issue.
* jtag_stm32:
- Fix incorrect handling of registers.
* pwm:
- Avoid Unicode string literals (bug #569).
* spi:
- - OUT_PYTHON docs: Fix order of MISO/MOSI data items.
+ - OUTPUT_PYTHON docs: Fix order of MISO/MOSI data items.
- Tell stacked decoders about missing CS# signal.
- Add binary output facilities for MISO/MOSI (bug #424).
- Don't decode data lines if CS# isn't asserted (bug #559).
projects / libsigrokdecode.git / blobdiff