* along with this program. If not, see <http://www.gnu.org/licenses/>.
*/
-/* mostly stolen from src/hardware/saleae-logic16/ */
+/*
+ * This driver implementation initially was derived from the
+ * src/hardware/saleae-logic16/ source code.
+ */
#include <config.h>
-#include <glib.h>
-#include <libusb.h>
-#include <stdlib.h>
-#include <string.h>
-#include <math.h>
+
#include <libsigrok/libsigrok.h>
+#include <string.h>
+
#include "libsigrok-internal.h"
#include "protocol.h"
else
conn_devices = NULL;
- /* Find all LA2016 devices and upload firmware to them. */
+ /* Find all LA2016 devices, optionally upload firmware to them. */
devices = NULL;
libusb_get_device_list(drvc->sr_ctx->libusb_ctx, &devlist);
for (i = 0; devlist[i]; i++) {
break;
}
if (!l) {
- /* This device matched none of the ones that
- * matched the conn specification. */
+ /*
+ * A connection parameter was specified and
+ * this device does not match the filter.
+ */
continue;
}
}
if (des.idVendor != LA2016_VID || des.idProduct != LA2016_PID)
continue;
- /* Already has the firmware */
+ /* USB identification matches, a device was found. */
sr_dbg("Found a LA2016 device.");
sdi = g_malloc0(sizeof(struct sr_dev_inst));
sdi->status = SR_ST_INITIALIZING;
fw_updated = 0;
dev_addr = libusb_get_device_address(devlist[i]);
if (des.iProduct != 2) {
- sr_info("device at '%s' has no firmware loaded!", connection_id);
+ sr_info("Device at '%s' has no firmware loaded.", connection_id);
if (la2016_upload_firmware(drvc->sr_ctx, devlist[i], des.idProduct) != SR_OK) {
- sr_err("uC firmware upload failed!");
+ sr_err("MCU firmware upload failed.");
g_free(sdi->connection_id);
g_free(sdi);
continue;
}
fw_updated = g_get_monotonic_time();
- dev_addr = 0xff; /* to mark that we don't know address yet... ugly */
+ /* Will re-enumerate. Mark as "unknown address yet". */
+ dev_addr = 0xff;
}
sdi->vendor = g_strdup("Kingst");
continue;
if ((sdi->status == SR_ST_INITIALIZING) || (sdi->status == SR_ST_INACTIVE)) {
- /*
- * Check device by its physical USB bus/port address.
- */
+ /* Check physical USB bus/port address. */
if (usb_get_port_path(devlist[i], connection_id, sizeof(connection_id)) < 0)
continue;
- if (strcmp(sdi->connection_id, connection_id))
- /* This is not the one. */
+ if (strcmp(sdi->connection_id, connection_id)) {
+ /* Not the device we looked up before. */
continue;
+ }
}
if (!(ret = libusb_open(devlist[i], &usb->devhdl))) {
- if (usb->address == 0xff)
+ if (usb->address == 0xff) {
/*
- * First time we touch this device after FW
- * upload, so we don't know the address yet.
+ * First encounter after firmware upload.
+ * Grab current address after enumeration.
*/
usb->address = libusb_get_device_address(devlist[i]);
+ }
} else {
sr_err("Failed to open device: %s.", libusb_error_name(ret));
ret = SR_ERR;
ret = libusb_claim_interface(usb->devhdl, USB_INTERFACE);
if (ret == LIBUSB_ERROR_BUSY) {
- sr_err("Unable to claim USB interface. Another "
- "program or driver has already claimed it.");
+ sr_err("Cannot claim USB interface. Another program or driver using it?");
ret = SR_ERR;
break;
} else if (ret == LIBUSB_ERROR_NO_DEVICE) {
ret = SR_ERR;
break;
} else if (ret != 0) {
- sr_err("Unable to claim interface: %s.", libusb_error_name(ret));
+ sr_err("Cannot claim USB interface: %s.", libusb_error_name(ret));
ret = SR_ERR;
break;
}
if ((ret = la2016_init_device(sdi)) != SR_OK) {
- sr_err("Failed to init device.");
+ sr_err("Cannot initialize device.");
break;
}
devc = sdi->priv;
/*
- * If the firmware was recently uploaded, wait up to MAX_RENUM_DELAY_MS
- * milliseconds for the FX2 to renumerate.
+ * When the sigrok driver recently uploaded firmware, wait for
+ * the FX2 to re-enumerate. Deal with the condition that the
+ * MCU can take some 2000ms to be gone from the bus before it
+ * re-appears executing the recently uploaded firmware.
*/
ret = SR_ERR;
if (devc->fw_updated > 0) {
sr_info("Waiting for device to reset after firmware upload.");
- /* Takes >= 2000ms for the uC to be gone from the USB bus. */
- reset_done = devc->fw_updated + 18 * (uint64_t)1e5; /* 1.8 seconds */
+ reset_done = devc->fw_updated;
+ reset_done += 1800 * 1000; /* 1.8 seconds */
now = g_get_monotonic_time();
if (reset_done > now)
g_usleep(reset_done - now);
}
if (ret != SR_OK) {
- sr_err("Unable to open device.");
+ sr_err("Cannot open device.");
return SR_ERR;
}
if (!sdi->conn)
return SR_ERR_ARG;
usb = sdi->conn;
- if (usb->address == 255) {
- /* Device still needs to re-enumerate after firmware
- * upload, so we don't know its (future) address. */
+ if (usb->address == 0xff) {
+ /*
+ * Device still needs to re-enumerate after firmware
+ * upload, so we don't know its (future) address.
+ */
return SR_ERR;
}
*data = g_variant_new_printf("%d.%d", usb->bus, usb->address);
{
struct dev_context *devc;
- devc = sdi->priv;
-
switch (key) {
case SR_CONF_SCAN_OPTIONS:
case SR_CONF_DEVICE_OPTIONS:
return STD_CONFIG_LIST(key, data, sdi, cg, scanopts, drvopts, devopts);
case SR_CONF_SAMPLERATE:
+ if (!sdi)
+ return SR_ERR_ARG;
+ devc = sdi->priv;
if (devc->max_samplerate == SR_MHZ(200)) {
*data = std_gvar_samplerates(ARRAY_AND_SIZE(samplerates_la2016));
}
return SR_OK;
}
-static void send_chunk(struct sr_dev_inst *sdi,
- const uint8_t *packets, unsigned int num_tfers)
-{
- struct dev_context *devc;
- struct sr_datafeed_logic logic;
- struct sr_datafeed_packet sr_packet;
- unsigned int max_samples, n_samples, total_samples, free_n_samples;
- unsigned int i, j, k;
- int do_signal_trigger;
- uint16_t *wp;
- const uint8_t *rp;
- uint16_t state;
- uint8_t repetitions;
-
- devc = sdi->priv;
-
- logic.unitsize = 2;
- logic.data = devc->convbuffer;
-
- sr_packet.type = SR_DF_LOGIC;
- sr_packet.payload = &logic;
-
- max_samples = devc->convbuffer_size / 2;
- n_samples = 0;
- wp = (uint16_t *)devc->convbuffer;
- total_samples = 0;
- do_signal_trigger = 0;
-
- if (devc->had_triggers_configured && devc->reading_behind_trigger == 0 && devc->info.n_rep_packets_before_trigger == 0) {
- std_session_send_df_trigger(sdi);
- devc->reading_behind_trigger = 1;
- }
-
- rp = packets;
- for (i = 0; i < num_tfers; i++) {
- for (k = 0; k < NUM_PACKETS_IN_CHUNK; k++) {
- free_n_samples = max_samples - n_samples;
- if (free_n_samples < 256 || do_signal_trigger) {
- logic.length = n_samples * 2;
- sr_session_send(sdi, &sr_packet);
- n_samples = 0;
- wp = (uint16_t *)devc->convbuffer;
- if (do_signal_trigger) {
- std_session_send_df_trigger(sdi);
- do_signal_trigger = 0;
- }
- }
-
- state = read_u16le_inc(&rp);
- repetitions = read_u8_inc(&rp);
- for (j = 0; j < repetitions; j++)
- *wp++ = state;
-
- n_samples += repetitions;
- total_samples += repetitions;
- devc->total_samples += repetitions;
- if (!devc->reading_behind_trigger) {
- devc->n_reps_until_trigger--;
- if (devc->n_reps_until_trigger == 0) {
- devc->reading_behind_trigger = 1;
- do_signal_trigger = 1;
- sr_dbg(" here is trigger position after %" PRIu64 " samples, %.6fms",
- devc->total_samples,
- (double)devc->total_samples / devc->cur_samplerate * 1e3);
- }
- }
- }
- (void)read_u8_inc(&rp); /* Skip sequence number. */
- }
- if (n_samples) {
- logic.length = n_samples * 2;
- sr_session_send(sdi, &sr_packet);
- if (do_signal_trigger) {
- std_session_send_df_trigger(sdi);
- }
- }
- sr_dbg("send_chunk done after %d samples", total_samples);
-}
-
-static void LIBUSB_CALL receive_transfer(struct libusb_transfer *transfer)
-{
- struct sr_dev_inst *sdi;
- struct dev_context *devc;
- struct sr_usb_dev_inst *usb;
- int ret;
-
- sdi = transfer->user_data;
- devc = sdi->priv;
- usb = sdi->conn;
-
- sr_dbg("receive_transfer(): status %s received %d bytes.",
- libusb_error_name(transfer->status), transfer->actual_length);
-
- if (transfer->status == LIBUSB_TRANSFER_TIMED_OUT) {
- sr_err("bulk transfer timeout!");
- devc->transfer_finished = 1;
- }
- send_chunk(sdi, transfer->buffer, transfer->actual_length / TRANSFER_PACKET_LENGTH);
-
- devc->n_bytes_to_read -= transfer->actual_length;
- if (devc->n_bytes_to_read) {
- uint32_t to_read = devc->n_bytes_to_read;
- if (to_read > LA2016_BULK_MAX)
- to_read = LA2016_BULK_MAX;
- libusb_fill_bulk_transfer(
- transfer, usb->devhdl,
- 0x86, transfer->buffer, to_read,
- receive_transfer, (void *)sdi, DEFAULT_TIMEOUT_MS);
-
- if ((ret = libusb_submit_transfer(transfer)) == 0)
- return;
- sr_err("Failed to submit further transfer: %s.", libusb_error_name(ret));
- }
-
- g_free(transfer->buffer);
- libusb_free_transfer(transfer);
- devc->transfer_finished = 1;
-}
-
-static int handle_event(int fd, int revents, void *cb_data)
-{
- const struct sr_dev_inst *sdi;
- struct dev_context *devc;
- struct drv_context *drvc;
- struct timeval tv;
-
- (void)fd;
- (void)revents;
-
- sdi = cb_data;
- devc = sdi->priv;
- drvc = sdi->driver->context;
-
- if (devc->have_trigger == 0) {
- if (la2016_has_triggered(sdi) == 0) {
- /*sr_dbg("not yet ready for download...");*/
- return TRUE;
- }
- devc->have_trigger = 1;
- devc->transfer_finished = 0;
- devc->reading_behind_trigger = 0;
- devc->total_samples = 0;
- /* we can start retrieving data! */
- if (la2016_start_retrieval(sdi, receive_transfer) != SR_OK) {
- sr_err("failed to start retrieval!");
- return FALSE;
- }
- sr_dbg("retrieval is started...");
- std_session_send_df_frame_begin(sdi);
-
- return TRUE;
- }
-
- tv.tv_sec = tv.tv_usec = 0;
- libusb_handle_events_timeout(drvc->sr_ctx->libusb_ctx, &tv);
-
- if (devc->transfer_finished) {
- sr_dbg("transfer is finished!");
- std_session_send_df_frame_end(sdi);
-
- usb_source_remove(sdi->session, drvc->sr_ctx);
- std_session_send_df_end(sdi);
-
- la2016_stop_acquisition(sdi);
-
- g_free(devc->convbuffer);
- devc->convbuffer = NULL;
-
- devc->transfer = NULL;
-
- sr_dbg("transfer is now finished");
- }
-
- return TRUE;
-}
-
-static void abort_acquisition(struct dev_context *devc)
-{
- if (devc->transfer)
- libusb_cancel_transfer(devc->transfer);
-}
-
static int configure_channels(const struct sr_dev_inst *sdi)
{
struct dev_context *devc;
devc = sdi->priv;
if (configure_channels(sdi) != SR_OK) {
- sr_err("Failed to configure channels.");
+ sr_err("Cannot configure channels.");
return SR_ERR;
}
devc->convbuffer_size = 4 * 1024 * 1024;
if (!(devc->convbuffer = g_try_malloc(devc->convbuffer_size))) {
- sr_err("Conversion buffer malloc failed.");
+ sr_err("Cannot allocate conversion buffer.");
return SR_ERR_MALLOC;
}
devc->ctx = drvc->sr_ctx;
if ((ret = la2016_start_acquisition(sdi)) != SR_OK) {
- abort_acquisition(devc);
+ la2016_abort_acquisition(sdi);
return ret;
}
devc->have_trigger = 0;
- usb_source_add(sdi->session, drvc->sr_ctx, 50, handle_event, (void *)sdi);
+ usb_source_add(sdi->session, drvc->sr_ctx, 50,
+ la2016_receive_data, (void *)sdi);
std_session_send_df_header(sdi);
int ret;
ret = la2016_abort_acquisition(sdi);
- abort_acquisition(sdi->priv);
return ret;
}